Centre For Cellular And Molecular Biology Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Costs
EMD
₹ 54,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Precision Ac System For Ngs Facility
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2020_CSIR_54143_1Bid Award Id
ViewTender No
CCMB/WKS-35/19-20Tender Authority
Centre For Cellular And Molecular Biology ViewPurchaser Address
-Website
http://https://www.csir.res.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Artificial load testing with Heater Bank for 12 Hours load bank for 60 KVA for continous running ( condenser load test procedure for 24 hours and submit the test reports/ complete in all respects as per the directions of the Engineer-in-Charge.
2
-
-
Loading, Unloading,Shifting and Erection of PAC Units in the Central Area First Floor.
2
-
-
Canvass ( between top discharge plenum and PAC on discharge and duct)
4
-
-
SITC OF MS STRUCTURE WORK:
-
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete in all respects/ as per the site conditions/ as per the directions of the Engineer - in - Charge including ( a) 2 Nos of Supply & Installation of MS stand for indoor unir. The stand should be coated with one coat of red oxide and one coat with rust proof epoxy paint. Height of the stand shall be 250mm, complete in all respects( 50x50x6mm MS angle, 1100mm x 850mm. MAKE : SAIL / VIZAG ( RINL) /TATA / JINDAL ( b ) 2 Nos. Supply & Installation of MS Fabricated platform/ Structural support ( for keeping ODU with cat walk & necessary support ) for Outdoor unit. The Stand should be coated with one coat of Red Oxide and One coat with rust proof epoxy paint ( Size: 3000mm x 1200mmx1000mm) with " C " channel ( 100 x 50 x 6mm ) for minimum 450Kgs loading capacity. Complete in all respects / as per the site conditions/ as per the directions of the Engineer-in-Charge. MAKE : SAIL / VIZAG(RINL)TATA / JINDAL
175
-
-
HARD DRAWN COPPER PIPE:
-
-
-
Supply & Installation of 18 G Hard Drawn Copper Piping between Indoor & Outdoor for Suction & Discharge line of suitable size including all fitting & accessories. Copper Piping should be suitable supported at regular intervals ( also include minor civil works, hot gas and liquid line to be painted with enamal paint and cable tray with top cover for copper pipe routing ). The Copper pipe should be insulated with 13mm thick nitrile rubber insulation inside the condition area complete in all respects/ as per the site condition/ as per the direction of the Engineer-in-Charge. Suction and discharge to be considered as one circuit. MAKE : MANDEV/ NIPPON/ NISSAN/TOTALINE.
-
-
-
Hard Drawn Copper Pipe 18G 5/8 ( for liquid line )
20
-
-
Hard Drawn Copper Pipe 18 G 7/8 ( for discharge line )
20
-
-
MCB AND DB (MAKE L&T / GE / SIEMENS / SCHNEIDER ELECTRIC ):
-
-
-
Supplying & Fixing following rating, four pole, 415 Volts, Isolator in the existing MCB DB complete with connections, testing and commissioning etc., as required.
-
-
-
63 A , 4 Pole Isolator
1
-
-
Supplying and fixing 32 Amps rating ( 3 Ph 8 way) 240/415 Volts, 10 kA, " C " , Curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB Complete with connections, testing and commissioning etc., as required.
-
-
-
Triple Pole and Neutral
2
-
-
Supplying & Fixing Cable end boxes ( IP 43 ) suitable for triple pole and neutral sheet steel, Vertical MCB distribution board , 415 Volts, on Surface/ recess, complete with testing and commissioning etc.,.
3
-
-
M V CABLES
-
-
-
Supplying and laying of the following size XLPE Insulated PVC sheathed Aluminium/Copper conductor U/G Cable of 1.1Kv grade as required confirming to IS specification and of approved make only. The cables shall be laid in existing cable trench / cable tray / open duct / surface / Hume pipes etvc., as required complete in all respects as per the site conditions and as per the instructions of the Engineer-in-Charge.
-
-
-
Supply & Installation of XLPE Copper Armoured Control cable between Indoor & outdoor units . Size 3 C x 2.5mm Sqmm. MAKE POLYCAB / FINOLEX.
35
-
-
Supply & Installation of 4C x 1 SQMM flexible cable for Sequential controller operation & water detector of both the units . MAKE: POLYCAB / FINOLEX.
20
-
-
Supply & Installation of XLPE Copper Armoured Power Cabling between isolator & indoor unit for bothe units. SIZE: 4c X 10 Sqmm .The scope of work also include making 3Phse connection from the existing source to PAC units. MAKE :Polycab / Finolex.
20
-
-
M V CABLES LAYING
-
-
-
Laying & Fixing of one number PVC insulated and PVC sheathed XLPE Power cable of 1.1Kv gradeof following size on Cable Tray as required.
-
-
-
UPTO 35 Sq.mm (clamped with 1 mm thick saddle)
75
-
-
MV CABLE JOINTING AND END TERMINATION :
-
-
-
Supplying & making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC shethered / XLPE Aluminium conductor cable of 1.1kv Grade as required.
-
-
-
4 x 10 SQMM ( 25MM )
6
-
-
CPVC PIPE
-
-
-
Providing & Fixing Chlorinated Polyvinyal Chloride ( CPVC) pipe having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00mt spacing and providing necessary supports etc., This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete in all respects as per the site conditions and as per the directions of the Engineer-in-Charge . Internal work - Exposed on Wall. NOTE: CPVC piping for humidifier line . MAKE: SUDHAKAR
-
-
-
25mm nominal Outer dia Pipes.
10
-
-
32mm nominal Outer dia Pipes
10
-
-
BALL VALVES:
-
-
-
Providing & Fixing ball valve ( brass ) of approved quality, High or low pressure, with plastic floats complete. MAKE : ZOLOTO / AUDCO ( L & T )
-
-
-
25 mm nominal bore
3
-
-
THERMAL INSULATION WORKS ( FOR COPPER PIPE AND DUCT )
-
-
-
Supplying, laying, fixing, testing and commissioning of following thickness XLPE CLOSED CELL elastrometic nitrile foam soft rubber faced with aluminium foil of Class " O " ( with necessary clamps, vibration isolators and fittings etc., ) duly insulated with following closed cell elastometic nitrile rubber of minimum 45Kgs/cum density, thermal conductivity 0.037 W/MK or better at 20 Deg. mean temperature class " O " insulation applied by suitable seals, taps, strips, adhesive, adhesive rolls, 3 " Al. Tape for longitudinal and transerve joints and matiblock glue etc., as per specifications and as required complete in all respects/ as per site conditions and as per the instructions of the Engineer-in-Charge. MAKE : TROCELLEN / L FLEX / SUPEREME / PARAMOUNT / AEROFLE /ARMAFLEX/ VIDOFLEX . INSULATION : ( NITRILE / EPDM ) MAKE PARAMOUT /SUPEREME /AEROFLEX/ARMAFLEX/SUPERION/VIDOFLEX / K FLEX.
-
-
-
6mm thick nitrile rubber insulation ( For drain line )
10
-
-
9mm thick nitrile rubber insulation ( for return air duct )
60
-
-
13mm thick nitrile rubber insulation ( for suction and discharge lines)
40
-
-
16mm thick nitrile rubber insulation ( for inside supply air duct )
60
-
-
25mm thick of nitrile rubber insulation ( for Outside supply air duct )
60
-
-
REMOVAL OF EXISTING DUCTS ALONG WITH DUCT MODIFICATIONS AND MAKING DUMMIES:
-
-
-
Removing of the existing ducts along with duct modifications and making dummies including shifting, fixing, modification works if required laying of old duct, re-routing etc., including GI Sheets, nut, bolts, GI supports, neoprene rubber gaskets, iron angles frames for all joints, vanes, hangers, silicon sealants for all longitudinal joints complete in all respects / as per the site conditions and as per the instructions of the Engineer-in- Charge.
1
-
-
AIR DISTRIBUTION SYSTEM:
-
-
-
Supply, Installation, Balancing and Commissioning of fabricated at site GSS GI Ducting sheet with cl VIII rectangular / round ducting complete with including providing GI supports, neoprene rubber gaskets, elbows, spliter dampers,iron angle frames for all joints, vanes, hangers, silicon sealants for all longitudinal joints, necessary support/ scaffholding, supports and necessary hardware for comfort application if required etc., as per the site requirements and conditions and as per the instructions of the Engineer-in-Charge, complete in all respects ( NOTE DUCTING WORK IS TO BE CARRIED OUT IN CENTRAL AREA FIRST FLOOR ). MAKE : SAIL / JINDAL / TATA
-
-
-
22G ( thickness 0.80MM sheet )
45
-
-
20G ( thickness 1.00mm )
45
-
-
GRILLS / DIFFUSERS / DAMPERS :
-
-
-
Supplying & Fixing of Powder coated extruded aluminium supply air grills with aluminium volume control dampers ( 150mm Liner Supply Air Gril with 15 Dge ( Deflection ) for supply of air terminals in comfort area as per the specifications and as per the requirements of site conditions and instructions of the Engineer-in-Charge complete in all respects. GRILL MAKE: CARRYAIR / COSMOS /DYNACRAFT/AIR PRODUCTS/RAVISTAR. VOLUME CONTROL MAKE: CARRYAIR /GEORGE RAO & CO /AIR PRODUCT / MHPPL.
4
-
-
Supplying & Fixing of Powder Coated extruded aluminium return air grills with louvers but without volume control damper for return air terminals in comfort area, as per specifications and asper the site requirement and instructions of the Engineer-in-Charge complete in all respects. GRILL MAKE: CARRRY AIR / COSMOS / DYNA CRAFTS / AIR PRODUCTS / RAVI STAR.
4
-
-
DOUBLE SKIN PLENUM:
-
-
-
Supply, Installation,Testing & Commissioning of Ceiling suspended modular double skin plenum with 25mm thick PUFF sandwich insulated panel with 24 G blue pre coated out side 24 G plain coated inside with required hat sections, screws, gaskets, hingers, bolts, nuts, and handless etc., ( Outer skin 0.8mm GI powder coated and inner skin 0.8mm plain GI double skin . AHU Plenum, Factory fabricated frame, Aluminium extruded penta post frame with nylon corners. Panels outer 22G GI pre-coated, inner 22G GI Plain sheet insulation PUFF thickness 25mm ) and in the PLENUM. VCD provision including supports, channels threaded down rods, anchor bolts, nuts, washers etc., as per the requirements of site conditions and instructions of the Engineer-inm-Charge complete in all respects. MAKE : BLUE STAR / VOLTAS / CARRIER / I CLEAN / SAGAR AIR / MSR
15
-
-
Supplying , Installation & Laying of double earthing out of GI wires of 8 SWG , Screws / nuts & bolts, clamps etc., as per the site requirements and instructions of the Engineer-in-Charge complete in all respects.
10
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements