Bharat Sanchar Nigam Limited Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Costs
EMD
₹ 7,300Document Cost
₹ 590Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_BSNL_190460_1Bid Award Id
ViewTender No
NIT No.07/NIT/CETSCZ/HYD/2024Tender Authority
Bharat Sanchar Nigam Limited ViewPurchaser Address
-Website
http://https://www.bsnl.co.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
2
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights:
-
-
-
Foundations, footings, bases of columns, etc. for mass concrete
13
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500 D or more.
100
-
-
Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand)
25
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. .
900
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. .
-
-
-
Hot finished welded type tubes.
325
-
-
Providing and fixing bolts including nuts and washers complete.
25
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade :
-
-
-
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).
25
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
-
-
-
Two or more coats on new work.
25
-
-
Extra for galvanising (of thickness not less than 120 microns) on M.S angles , flats, gussets plates, bolts, nuts and other fastners.
1225
-
-
Providing and fixing anchor fastners (expansion fastners) of approved quality including drilling holes in RCC and fixing complete
-
-
-
a) 16 mm dia and 100mm lenth
48
-
-
b) 12 mm dia and 100mmm lenth
20
-
-
Providing and supplying heavy duty injection adhesive for fixing threaded bolts in wet/dry conditions HILTI RE500 for dia upto 40mm of HILTI India Pvt. Ltd. The system to be made of two foils consisting of resin and hardener foil pack. The system can be used for fixing threaded bolts viz HAS-E-M8 to 39 rods. The cost inclusive of material, epoxy fasteners, drilling holes in concrete etc., complete as directed by Engineer-In Charge.
-
-
-
16mm dia epoxy based anchor fasteners
12
-
-
Drilling holes of 16mm dia in RCC slab/beam upto a depth 120 mm and embedding 12mm dia TMT bars of grade Fe 500D in the hole including grouting the hole with FOSROCK LOKFIX chemical or approved equivalent to anchor reinforcement excluding the cost of reinforcement as per direction of Engineer-in-Charge. ( the work shall be carried out as per manufactures specification through the Applicator approved by the manufacturer)
24
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements