Bharat Electronics Limited Tender

Supplying and stacking of soil suitable for filling at site (to be brought from outside and got approved) including transportation and stacking at site as per the direction of Engineer In Charge. Spreading, levelling and consolidation of brought out earth in layers not exceeding 20 cms in depth consolidating each deposited layer by ramming and watering complete including preparation of the surface spreading and leveling to the required grade/level in layers not exc. 20 cms In depth, breaking clods, watering and consolidated under optimum moisture conditions each layer of earth shall be carefully moisture to give field moisture content of about +1% to -2% of the optimum moisture content (OMC). The OMC shall be determined according to IS 2720 (Pt.VIII) Methods of Tests for Soils. Each layer shall then be compacted by earth compacter

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level/or above plinth level and Thermomechanically treated bars of grade Fe500D or more. Base Rate: Rs. 65 per Kg

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) :With Modular bricks

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 5.0 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Kota stone slab flooring of 25mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying Glazed Vitrified tiles Matt/Antiskid finish of different sizes (thickness to be specified by the manufacturer) in floor with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Make: Kajaria (Base Rate-Rs.800/Sq.m)

Providing and fixing Ist quality ceramic glazed wall tiles of different size conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete Make: Kajaria (Base Rate-Rs.750/Sq.m)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of specified colour and shade Area of slab over 0.50 sqm.

Fixing of factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing SUB HEAD : 9 - WOOD & PVC WORK 696 hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing 100 mm wide Roller blinds made out of 100 mm non-woven fabric. The fabric shall be scotch guard protected, antistitic and shall be sanitised to resist fungal growth. The head channel shall be of 33 mm wide and 30 mm deep with a minimum valve thickness of 1.2 mm extruded from aluminium alloy finished in clear anodising to a thickness of 10 microns (Note: Height of the blind will be measured from top of the head rail to bottom of slat. length of the head rail shall be measured to the length of the blind) etc., complete.

Providing Second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length.

Providing and fixing 32 mm thick factory made laminated glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick float glass panes for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, all as per directions of Engineer-in-charge.

Providing and fixing composite doors of required size of Fimen/ Suraksha conforming to IS: 4020 (latest) to the following specification. The single leaf shutter shall be of rigid GRP sandwiched composite structure of 30mm thick (min) laminated on all sides with GRP skin fabricated using UV stabilised isophthalic Gel coat and one layer of 450 gsm E-Glass chopped strand Mat (CSM), Impregnated with polyester resin. The thickness of the skins shall be not less than 1.5mm thick. Expanded polystyrene (EPS) structural foam panel of density 20kg/cum shall be used as core material for the whole area of door except the wooden frame structure. The wooden reinforcements shall be made of seasoned sal wood block of minimum cross section 70 x 26mm for lock side, 40 x 26mm alround forming the frame the work for shutter and a minimum of 75mm wide intermediate strip for the width of the door for fixing locks and fixtures. The finish of shutter shall be grains and of approved colour. The door frame shall be of 90 x 60mm (min) and of same colour of shutter made with GRP sheets of 1.5mm min. thickness and reinforced with 3 Nos. of 200mm long, salwood pieces of suitable size on each vertical side of frame for fixing of hinges and locks and the balance portion of the frame shall be filled with light weight concrete including providing and fixing 6 Nos. of 260 x 25 x 5 mm size MS hold fasts, 3 Nos of 100mm long SS heavy duty hinges with counter sunk screws, 1 No. of 200mm long powder coated aluminium aldrop bolts, 2 Nos. of 125mm long powder coated aluminium plain door handles, 2 Nos. of 100mm long powder coated aluminium tower bolt for each shutter etc all complete.

Providing and fixing Door Closer C102 Single Door Closer godrej 60kg Cat.No.8340

Providing and fixing Dorset Door aldrop , with necessary screws etc.Atom 12 inch fancy aldrop chrome plated silver stain finish(wsa333-cpss)

Providing and fixing 200mm SS pull handle-D type with necessary screws etc.,complete.make by Godrej make code No 2801 or equivalent as per direction of Engr-in-charge

Providing and fixing 200 x 10 mm SS tower bolts with necessary screws etc., complete.make by Godrej make as per direction of Engr-in-charge

Providing and Fixing of Godrej Stain Steel Door Handle NEH06 -200 mm With Lock Set 1CK (Stain Steel Silver) .

Providing and fixing Dorset Door Stopper DS HT Z or equivalent,with necessary screws etc. complete. Single rubber stopper

Providing and fixing 50mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing 75mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing 110mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes

Providing and fixing 100 mm inlet and 75 mm outlet PVC trap of FINOLEX / SUPREME with stainless steel grating (with or without hole for PVC waste pipe of CHILLY/NOWAY make) including the cost of cutting and making good the walls and floors.etc., complete.

providing & fixing of SS floor jali 100mm thick etc complete as per direction of Engineer In Charge

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, including flush , conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked pastel solid plastic seat and lid (Hindware Cat. No.: 20154 (S-22) and Hindware sleek fresh cisternHealth faucet with 8mm dia, 1.2m long flexible tube & wall hook(Hindware Cat.No.F160001CP)

Providing and fixing ORISSA PAN WHITE IWC with integral type foot rest of Cat. No. 20004-HINDWARE or equivalent make etc., with 'P' or 'S' trap and all fittings like 10 litres capacity hindware make PVC flushing cistern, cutting and making good the walls and floors wherever required etc., complete as per direction of Engineer-in-charge

Providing and fixing white vitreous wash basin over the counter (as per catalogue. No. 10105 of hindware) of size 370x310 mm with single 15 mm pillar tap (Jaquar make FLR-CHR-5021M) and waste coupling (cat.- ALD-CHR-709) and bottle trap (ALD-769L 300x190 Bottle Trap (with Internal Partition) 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange), angular stop cock CON-053KN and PVC connection pipe with brass unions of `Jaquar' make with necessary coupling etc. cutting and making good the walls wherever required etc., complete

Providing and fixing Hindware make urinal basin of cat no 96008 with standard inlet and outlet pipe connections conceled in the wall, providing and fixing 15mm dia push type Bib cock (PRS-077) etc., including cutting and making good the walls and floors wherever required and servicing the unit etc. complete.

Providing and fixing of glass urinal partition (jaquar make: JSE CHR 810UC450X) on the wall using SS clamps of jaquar make all complete as per directions of engineer in charge

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (Make:Saint Gobin, Modi)

Providing and fixing 2-way Bib Cock with Wall Flange KUB-35037F of jaquar make and Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) 15 mm nominal bore ALD-CHR-579 with necessary fittings complete as directed by engineer in charge

Providing and fixing liquid soap container of Jaguar make cat no SDR-WHT-DJ0010F with glass bottle with matching colout CP screws etc complete.

Providing and fixing Double coat hook of Jaguar make cat no. AKB-CHR-35761P with matching CP screws etc complete

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type; With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing of Bitumen washer/GI Washer & nut after Removal of existing Nut, Washser and laying of PU sealent(fosroc nitoseal pu40 / equivalent) over the nut, including cleaning of roof sheet as directed by engineer in charge.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (Base Rate 65.00 per Kg)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595 x 595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.. Make: Armstrong,Gyprock (Note: False ceiling required to be fixed under SHED of Height 5m, necessary arrangements should be made by contractor)

PART-B ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-B

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. Group-A.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet.

Supplying and fixing following modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 module (200mm x 75mm).

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 module (125mm x 125mm).

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess including associated civil works etc., as required. 12 module (200mm x 150mm).

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit with acessories as required. copper wire 2 X 2.5 sq. mm + 1 X 2.5 sq. mm for earthing.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying of below mentioned specification LED luminaire & fixing of the same in the ceiling by providing required down rod/chain, clampsscrews/anchor bolt-nuts, washers etc., making electrical connections, earthing etc., as required/directed by engineer-in-charge. Mounting Type:- Recess Mount, Type:- 2Ft*2Ft luminaire, Input Power: 36 watt Ref model:-Wipro: Elate LED-CRCO10R036HP57G2 or equivalent in approved makes.

Supplying and fixing of 18W Surface/Recess mount downlighter, LED Fitting and fixing of the same with clamps screws/anchor bolts-nuts, washers etc., as required directed by engr-in charge. Ref:- similar to wipro LD80-171-XXX-60-SM. or equivalent in approved makes.

Supplying & erecting of 250 mm sweep, single phase plastic body exhaust fan with mesh cover/automatted shutters & all acessories and installation of the same by providing suitable nut/bolts/screws and making good electrical connection, earthing, testing etc. as required. The electrical connection shall be made by providing suitable size PVC insulated flexible copper cable from already provided ceiling rose as required. Ref model :- Bajaj(MAXIMADxI 200) or equivalent in approved makes.

Supplying of fully automatic hand drier suitable for 230V, 50Hz AC supply, twin blower integreted with timer cum infrared sensing system and fixing of the same on wall by providing suitable TW guttas, screws, bolt-nuts etc., as directed. (Ref make: DOLPHY DAHD0011, 1800W or equivalent approved makes.)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door.

Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.125 A,36KA,FPMCCB.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm size.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (32mm).

Supplying of LT power cable with Aluminium conductor, XLPE/PVC insulated, PVC inner sheathed, armoured, 1.1KV grade (A2XFY), confirming IS:7098(part-1) with relevant standards. 3.5C X 35 Sq mm. (Ref make: Finolex, Havells,KEI).

Supplying and fixing of 25 mm size of Casing and Caping Patti along with accessories on the wall/ column/ ceiling/truss as surface/recess system including cutting the wall and making good the same in case with associated civil works as required.