Water Resources Department Tender

Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of Reinforced Cement Concrete etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

HGS SS.20.B. Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, hales,murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

Earthwork excavation for Foundation in all kinds of soils inclusive of shoring, strutting and bailing out water wherever necessary, refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated etc, as shown by the departmental officers and clearing, levelling the site etc. complete complying with standard specifications and as directed by the Departmental Engineers.

Conveyance of earth including earthwork in all soils except hard rock requiring blasting and conveying with a lead of 3 Km by deploying earth moving machineries and tippers for formation of bunds in layers of suitable thickness , shores prior to placement of earthfill including extra earth filling breaking clods, sectioning extra watering to Optimum Moisture Content (OMC) and compaction of each layer to 95% of proctor density through deployment of appropriate compaction equipment (8-10 T power roller / Vibratory power roller / short width (+ 0.90M width drum) power roller or vibratory power roller / Fuel operated or electric operated vibratory plate compactors ensuring compaction of designed bund section including side slopes compaction complete as per specification etc. complete with standard specifications and as directed by the Engineer in Charge of the works.

Refilling the excavated earth for formation of bund in layers of 23 cm thick including benching, formation of bunds, breaking clods, watering to Optimum Moisture Content (OMC) and compaction of each layer to 95% of proctor density through deployment of appropriate compaction equipment (8-10 T power roller / Vibratory power roller / short width (+ 0.90M width drum) power roller or vibratory power roller / Fuel operated or electric operated vibratory plate compactors) ensuring compaction of designed bund section including side slopes etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Supplying and filling the M.Sand including the cost and conveyance of materials, watering, compacting etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Supplying and Spreading 25 to 63 mm size HBG Graded metal metal as directed by the Engineer in charge of the works complying with technical specification.

Supplying and filling the gravel including the cost and conveyance of materials, watering, compacting etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Supplying suitable gravel and providing gravel packing for revetment including stacking the same for taking pre-measurement, the charges for spreading and working with water to plastic state complete as directed by the Engineer in Charge of the works.

Supplying and filling gravel in between the gaps of Cement Concrete blocks etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Plain Cement Concrete grade M10 using 40mm (HBG) hard broken granite stone jelly to attain the specfiied characteristic strength not less than 10N/mm2 at 28 days for foundation ect., Including dewatering if found necessary and laid in layers of not more than 15 cm thick and curing ect., complete complying with standard specifications and as directed by the Engineer in charge of the work.

Without Boom Placer

By Using Boom Placer

Supplying and erecting steel centering for sides and soffits With strutting upto 3 m height for plain surfaces with all cross bracings using mild steel sheets of size 90 cm X 60 cm and BG 10 stiffened with welded mild steel angles of size 25 X 25 X 3 mm for boarding laid over country wood joists of size 10 X 6.5 cm spaced at about 90 cm c/c and suppoted by casurina props of 10 cm to 13 cm dia spaced at 75 cm c/c etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Supplying and erection of steel centering for sides and soffits of plain surfaces such as a slab etc. including strutting above 3m height for plain surface with all cross bracings using Mild Steel sheets of size 90cm. X 60cm. thickness of and B.G.10 stiffened with welded Mild Steel angles of size 25 X 25 X 3mm for boarding, laid over silver oaks (country wood) joists of size 10cmX 6.5cm (spaced at 90cm. Centre to centre) and supported by casuarina props of 10 to 13cm dia (spaced at 75cm) Centre to centre complying with standard specification and as directed by departmental Engineers.

Supplying and erecting steel centering for sides and soffits Withoutstrutting upto 3 m height for plain surfaces with all cross bracings using mild steel sheets of size 90 cm X 60 cm and BG 10 stiffened with welded mild steel angles of size 25 X 25 X 3 mm for boarding laid over country wood joists of size 10 X 6.5 cm spaced at about 90 cm c/c and suppoted by casurina props of 10 cm to 13 cm dia spaced at 75 cm c/c etc. complete complying with standard specifications and as directed by the Engineer in Charge of the works.

Supplying, fabricating and placing in position of mild steel (MS) or ribbed tor steel grills for reinforcement of all RCC works including cost of steel, binding wire, labour charges for de-coiling, cutting, bending and tying the grills etc. complete complying with standard specifications and as directed by the Departmental Engineers.

Providing and Placing in position of Plain Cement Concrete of grade M15 design Mix for works with well graded hard aggregates and the nominal maximum of coarse aggregate of 20 mm gauge weigh batching the ingredients and mixing in batching plant (to produce concrete of the specified characteristic strength of 15N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers not more than 15cm thick and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing etc. complete complying with standard specifications and as directed by the the Engineer incharge of the work.

Providing and Placing in position of Plain Cement Concrete M20 design Mix for works with well graded hard aggregates and the nominal maximum of coarse aggregate of 40 mm gauge weigh batching the ingredients and mixing in batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position etc. complete complying with standard specifications and as directed by the Engineer in charge of the work.

Above sill Upto 4.50 M level & Below sill upto 1.5 M

Above sill Upto 4.50 M level & Below sill upto 1.5 M

Above 4.50 M level to 6.00 M level

Above 1.50 M level to 4.50 M level below sill

Providing and Placing in position of Plain Cement Concrete M20 design Mix for works with well graded hard aggregates and the nominal maximum of coarse aggregate of 20 mm gauge weigh batching the ingredients and mixing in batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position etc. complete complying with standard specifications and as directed by the Engineer in charge of the work.

Without Boom Placer

By Using Boom Placer

Providing and placing Reinforced Cement Concrete M20 design Mix with well graded hard aggregates and the nominal maximum of coarse aggregate of 20 mm gauge weigh batching the ingredients and mixing in batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specifications as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position etc. complete complying with standard specifications and as directed by the Engineer incharge of the work.

Providing and Placing in position of Reinforced Cement Concrete M25 grade Mix with well graded hard aggregates and the nominal maximum of coarse aggregate of 20 mm gauge weigh batching the ingredients and mixing in batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface, water curing so as to attain the profile and strength specified in the approved drawing and specification as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position etc. complete complying with standard specifications and as directed by the Departmental Engineers.

Providing and Placing in position of Reinforced Cement Concrete M30 grade Mix with well graded hard aggregates and the nominal maximum of coarse aggregate of 20 mm gauge weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 30N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification.

Rough stone dry packing using New rough stones revetment stone for launching apron including stacking charges for pre-measurement and finishing etc. complete complying with standard specifications and as directed by the Engineer in charge of the work.

Providing and Preparation of sub grade (as per technical specification) duly moisture and duly removing the surface irregularities including dewatering and laying plain cement concrete lining 100mm thick of M20 Grade mix concrete using hard course aggregate with nominal maximum size of 20mm downgraded to IS specified grading to have well graded aggregate weigh batching the ingredients along with Air Entraining Agent (200 ml per bag of cement) and mixing these in batch mixing plant (concrete mix to yield 28 days characteristic compressive strength of 15 N/mm2) transporting to placement site by transit mixer and mechanised placement of concrete over the sub grade on canal slope by using Concrete Paver including compaction , trimming, consolidation of concrete as per technical specifications and watering curing of the lining. The sub grade shall be well prepared, dressed and rolled to true surface of specified section to form a firm compacted base for the lining etc. complete complying with standard specifications and as directed by the Departmental Engineers. on canal Bed

Providing & Placing pre-cast cylindrical porous plug of 75 mm Dia and 300 mm in length in porous concrete CC 1:0:4, one in each panel in the bed @ 2.7m c/c, in filter having size 40 x 40 x 40 cm m M-Sand and 25 x 25 x 25 cm metal including excavation and separating filter material etc. complete complying with standard specifications and as directed by the Departmental Engineers.. (as per drawing of the porous plug enclosed)

Providing and filling sealant material in Transverse contraction joint after thoroughly cleaning all the joints @ 2.70m c/c and finishing the surface to match with lining face with contractors own material etc. complete complying with standard specifications and as directed by the Departmental Engineers. (as per drawing of the transverse contraction joint enclosed)

Supplying and fixing of weld mesh 75mm x 50mm x 10gauge cost and conveyance of weld mesh to site of work and Dowel bar and including drilling and fixing of 50cm intervals over the brick wall surface incluiding all other incidental charges etc., complete and as directed by the Engineer in charge of the works.

Clean removal of the dirts deposited over brick wall surfaces, rubbing, cleaning, water washing filling the joint with epoxy grout and guniting with cement mortor 1:3 to an average thicknes of 40mm under the presser of 3 to 3.50 kg/m2 and finishing including hire charges for all the toils and planting and including sand blasting and all other incidential charges etc., complete and as directed by the Engineer in charge of the works.

Centering for all sofits of reinforced Cement Concrete and all other concrete works including cost of materials for scaffolding strutting to centering etc and cost of nails etc and all other incidential charges etc complete complying with standard specification and as directed by the Engineer in charges of the work.

Fabricating, supplying and erection of Screw Gearing Steel Shutters of Size up to 1.00m width consist of Skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 65x65x6mm Mild steel angle at an interval not more than 0.50 m and vertical stiffeners made out of same section at an interval not more than 0.60 m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc.,Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipments.Erecting the new shutter and the shuttering arrangements in the vent in proper position using necessary hosting equipments. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red oxide primer. The rate including the cost of material , consumables , labours , power charges, conveyance charges, charges for all equpiments required conveying the dismantled material to the section stores, cost of petty civil works, trial operations of shutter and warranty for 5 years etc., complete.

Fabricating, supplying and erection of Screw Gearing Steel Shutters of Size above 1.00m and upto 2.00 m width consist of Skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50 mm steel channel (ISmC) at an interval not more than 0.50 m and vertical stiffeners made out of same section at an interval not more than 0.60 m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc.,Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipments.Erecting the new shutter and the shuttering arrangements in the vent in proper position using necessary hosting equipments. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red oxide primer. The rate including the cost of material , consumables , labours , power charges, conveyance charges, charges for all equpiments required conveying the dismantled material to the section stores, cost of petty civil works, trial operations of shutter and warranty for 5 years etc., complete.

Fabricating, supplying and erection of Screw Gearing Steel Shutters of Size above 2.00m and upto 3.00 m width consist of Skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50 mm steel channel (ISmC) at an interval not more than 0.50 m and vertical stiffeners made out of same section at an interval not more than 0.60 m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc.,Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipments.Erecting the new shutter and the shuttering arrangements in the vent in proper position using necessary hosting equipments. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red oxide primer. The rate including the cost of material , consumables , labours , power charges, conveyance charges, charges for all equpiments required conveying the dismantled material to the section stores, cost of petty civil works, trial operations of shutter and warranty for 5 years etc., complete.

Fabricating, supplying and fixing of Top beam made out of 150x75mm (ISMB 150) duly drilled to suit the Head set assembly with required bed bolt made out of 25 mm Mild Steel Round rod duly threaded with suitable anchorage arrangements to a height of 0.60 m with necessary Fish plate made out of 12 mm Mild steel plate of size 0.30x0.15m, 2 Nos with required holes.Conveying and leading the top beam arrangements to the worksite. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking at the section store. The top beam should be painted with two coats of Anticorrosive black paint over one coat of red oxide primer. The rate including cost of materilas, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc., complete.

Fabricating, supplying and fixing of Top beam made out of 200x100 mm (ISMB 200) duly drilled to suit the Head set assembly with required bed bolt made out of 25 mm Mild Steel Round rod duly threaded with suitable anchorage arrangements to a height of 0.60 m with necessary Fish plate made out of 16 mm Mild steel plate of size 0.30x0.20m, 2 Nos with required holes.Conveying and leading the top beam arrangements to the worksite. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking at the section store. The top beam should be painted with two coats of Anticorrosive black paint over one coat of red oxide primer. The rate including cost of materilas, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc., complete.

Fabricating, supplying and fixing of shutter Groove angle made up of 65 x 65 x 6mm Mild steel angle for required height including welding hold fast of size 25 x 25 x 6mm Mild steel angle of 2 Nos on both sides and conveying and leading the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The Groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and including all other taxes etc., complete.

Fabricating supplying and fixing of shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos. on both sides and coveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store . The Groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials , consumables, labours, charges for all fabricating and hoisting equipments , conveyance , petty civil works and including all other taxes etc., complete.

Fabricating, suppllying and fixing of 63 mm dia screw rod made up of Mild steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes .Conveying and leading the screw rod to the work site . Fixing the screw rods to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod , conveying and stacking at section store. The screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials , labours, charges for all fabricating and hoisting equipments , conveyance charges for labours and materials and including all other taxes etc., complete.

Fabricating, suppllying and fixing of 80 mm dia screw rod made up of Mild steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes .Conveying and leading the screw rod to the work site . Fixing the screw rods to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod , conveying and stacking at section store. The screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials , labours, charges for all fabricating and hoisting equipments , conveyance charges for labours and materials and including all other taxes etc., complete.

Fabricating, supplying and fixing of Head set assembly heavy duty with hexagonal nut (approximate 70 Kg ) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the screw rod provided with thrust bearing for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly, conveying and stacking at section store. The Head Set assembly supplied with operating key and the both should be painted with two coats of Anticorrosive black paint over one coat of Red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for all machining equipments, conveyance charges for labours and materials and warranty for 5 years., etc, complete.

Fabricating, supplying and fixing of Head set assembly heavy duty with hexagonal nut (approximate 120 Kg ) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the screw rod provided with thrust bearing for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly, conveying and stacking at section store. The Head Set assembly supplied with operating key and the both should be painted with two coats of Anticorrosive black paint over one coat of Red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for all machining equipments, conveyance charges for labours and materials and warranty for 5 years., etc, complete.

GST at 18%