Tidel Park Limited Tender

Ground Floor - VIP Waiting Room 3 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - VIP Waiting Room 2 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - VIP Waiting Room Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Auditorium Vip Chair The seat should be made up of 1.2 ± 0.1cm. thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. the back foam should be designed with contoured lumber support for extra comfort. the chair should be available in three models: back size: 53.0cm.(w) x 73.0cm.(h), seat size: 54.6cm.(w) x 49.0cm.(d) the hr polyurethane foam should be moulded with density = 45 ±2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the fixed type mechanism should be made with a 0.8 ±0.05 cm thk hr steel spine welded to it and black powder-coated ( dft 40-60 microns ). The understructure should be made up of m.s.e.r.w. elliptical tube of size 4.5 ± 0.03cm x 1.9 ± 0.02cm x 0.25 ± 0.025cm welded to m.s.e.r.w tube of ∅ 1.6 ± 0.02cm x 0.2 ± 0.016cm thk. the understructure should be powder coated ( dft 40-60 microns ) in silver metallic gray. Overall Dimensions of Chair - Seat Height -46.0cm. Height -99.5cm. Width & Depth of Chair as measured from pedestal - Width 63.0 cm and Depth 69.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Auditorium Chair The rate shall be quote as per the image mention in volume-I.

Ground Floor - Auditorium Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge Reception Table - (Length - 2400mm, Depth - 1770, 870mm, Height - 1080mm)Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Access Flap along with a Grommet is provided on work surface for wire management Wire Management - Power box made with 0.8mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lapping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lapping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lapping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lapping. **Drawer bottom is made of 5.5thk MDF whiteboard, Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge Chair - PULSE MID BACK (Mb Seat, Adj. Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX, PULSAL): 45.0 cm. (W) x 65.3 cm.(H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE) {PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort. •Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. Overall Dimensions of Chair-WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge 3 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge 2 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge Flower Table Teakwood made of 25mm Thickness Solid Wood With Made out of with 8mm round toughened glass top with edging Size - 1ft Dia. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Reception Cum Waiting Lounge Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Officer Cabin Officer Table - Size - 2100mm x 2250mm x 750mm Primary Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Secondary Work Surface: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel: Made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under-structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400mm long metal Panel Drawer Slides. Drawer extension is 325mm. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Officer Cabin Officer Chair - SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H), Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression.BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type, • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position, • 5 position Tilt limiter giving option of variable tilt angle to the chair, • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm.LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors.The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter.The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2°.Overall Dimensions of Chair Seat Height - min 45.5 to max 55.5cm., Height - min 95.5 to max 105.5 cm., Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm.

Ground Floor - Officer Cabin Chair - PULSE MID BACK (Mb Seat, Adj. Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX, PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE) {PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort. •Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Officer Cabin Side Table - Size - 2350mm x 500mm x 750mm Top Panel: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Conference Hall Conference Table Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. MINGLE TABLE PLT - 22 SEATER, MINGLE MODULAR PLT_2 STR MAIN ST-2nos, MINGLE MODULAR PLT_2 STR SHARED ST (Size - 1350 X 600 X 740)-1nos, MINGLE MODULAR PLT_1 STR SHARED ST (Size - 675 X 600 X 740)-2Nos, MINGLE MODULAR PLT 1800W ST (Size - 1800 X 850 X 740)-1No Accessories - Dsk 2 way Name Plate, Dsk Mod Doc Shelf, Dsk HDMI wire Man (One packet Contain 8 Qty)-1No. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Conference Hall Officer Chair - PULSE Hi BACK (Mb Seat, Adj, Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX,PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE){PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm. The complete neckrest assembly is retro fit to the main chair. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Work Station Work Station Table Providing and placing UPBEAT DESK based modular workstation with System ht - 1200mm SCREENS: Main Fabric screen on stud. UNDERSTRUCTURE: Comprising of metal cross member between legs, DFINE PLUS legs made up of metal finish on end and shared leg with wire tray raiser the entire assemply is fixed to the worktop. Wire Management : Shared leg with wire tray raiser is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s wire tray assembly is provided below worktops. MODESTY PANEL: Porforated metal modesty 0.8 mm thk.modesty is mounted under neath the worktop with the help of the brackets. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w X 600 mm d. Pedestals- Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Work Station Officer Chair - PULSE Hi BACK (Mb Seat, Adj, Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX,PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE){PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm. The complete neckrest assembly is retro fit to the main chair. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - Work Station Side Table - Size - 2350mm x 500mm x 750mm Top Panel: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD PA Table - Size - 2100mm x 750mm x 750mm Primary Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Secondary Work Surface: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel: Made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under-structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400mm long metal Panel Drawer Slides. Drawer extension is 325mm. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD PA Chair - PULSE MID BACK (Mb Seat, Adj. Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX, PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE) {PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort. •Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD PA Side Table - Size - 2350mm x 500mm x 750mm Top Panel: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Waiting Lounge 3 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Waiting Lounge 2 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Waiting Lounge Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Waiting Lounge Flower Table Teakwood made of 25mm Thickness Solid Wood With Made out of with 8mm round toughened glass top with edging Size - 1ft Dia. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room MD Table The Main table shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in Smart Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be coated of MDF (medium density fiber ) with veneer coating and PU coating.The ERU Top shall be of MDF (medium density fiber) board duly finished with veneer and final PU coating. Size of ERU top 1900 Width mm x 480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management system also there is perfect storage side unit. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room MD Chair The seat should be made up of 1.2 ± 0.1cm. Made out of 18mm thick BWP plywood for seat and rest with high quality leather finish rexine with 5 prong powder coat leg. thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. the back foam should be designed with contoured lumber support for extra comfort. the chair should be available in three models: back size: 53.0cm.(w) x 73.0cm.(h), seat size: 54.6cm.(w) x 49.0cm.(d) the hr polyurethane foam should be moulded with density = 45 ±2 kg/m³ and hardness load 16 ± 2 kgf. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. .PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room Officer Chair The seat should be made up of 1.2 ± 0.1cm. thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. the back foam should be designed with contoured lumber support for extra comfort. the chair should be available in three models: back size: 53.0cm.(w) x 73.0cm.(h), seat size: 54.6cm.(w) x 49.0cm.(d) the hr polyurethane foam should be moulded with density = 45 ±2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the fixed type mechanism should be made with a 0.8 ±0.05 cm thk hr steel spine welded to it and black powder-coated ( dft 40-60 microns ). The understructure should be made up of m.s.e.r.w. elliptical tube of size 4.5 ± 0.03cm x 1.9 ± 0.02cm x 0.25 ± 0.025cm welded to m.s.e.r.w tube of ∅ 1.6 ± 0.02cm x 0.2 ± 0.016cm thk. the understructure should be powder coated ( dft 40-60 microns ) in silver metallic gray. Overall Dimensions of Chair - Seat Height -46.0cm. Height -99.5cm. Width & Depth of Chair as measured from pedestal - Width 63.0 cm and Depth 69.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room 2 Seater Sofa & 1 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 146.0CM. Depth (D): 90.5CM. Height (H): 85.5CM. Seat Height (SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Room Side Table - Size - 2350mm x 500mm x 750mm Top Panel: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

Ground Floor - MD Dining Room MD Dining Table with 4Nos of Chair. The rate shall be quote as per the image mention in volume-I.

First Floor - Reception Cum Waiting Lounge Reception Table - (Length - 2400mm, Depth - 1770, 870mm, Height - 1080mm) Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Grommet is provided on work surface for wire management Wire Management - Power box made with 0.8mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lapping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lapping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lapping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lapping. **Drawer bottom is made of 5.5thk MDF whiteboard, Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. The rate shall be quote as per the image mention in volume-I.

First Floor - Chair - PULSE MID BACK (Mb Seat, Adj. Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX, PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE) {PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort. •Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Reception Cum Waiting Lounge 3 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Reception Cum Waiting Lounge Flower Table Teakwood made of 25mm Thickness Solid Wood With Made out of with 8mm round toughened glass top with edging Size - 1ft Dia. The rate shall be quote as per the image mention in volume-I.

First Floor - Reception Cum Waiting Lounge Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

First Floor - Officer Cabin Officer Table - Size - 2100mm x 2250mm x 750mm Primary Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Secondary Work Surface: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel: Made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under-structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400mm long metal Panel Drawer Slides. Drawer extension is 325mm. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

First Floor - Officer Cabin Officer Chair - PULSE Hi BACK (Mb Seat, Adj, Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX,PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE){PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm. The complete neckrest assembly is retro fit to the main chair. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Officer Cabin Chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair - Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. The rate shall be quote as per the image mention in volume-I.

First Floor - Officer Cabin Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

First Floor - Business Center 3 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Business Center 2 Seater Sofa Seat foam: The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back foam: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under Structre: Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. Leg Assembly: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width(W): 206.0CM. Depth(D): 90.5CM. Height(H): 85.5CM. Seat Height(SH): 45.0CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Business Center Center Table Glass: It is 10 ±0.3 mm thick black tinted Toughened glass top. Understructure: Made out of 18mm BWR plywood, 1mm Laminate sheet. Width of table= 126.0 cm, Depth=60.0 cm, height=35.0 cm. The rate shall be quote as per the image mention in volume-I.

First Floor - Business Center Side Table - Size - 2350mm x 500mm x 750mm Top Panel: Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. The rate shall be quote as per the image mention in volume-I.

First Floor - Conference Hall Conference Table Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. MINGLE TABLE PLT - 22 SEATER, MINGLE MODULAR PLT_2 STR MAIN ST-2nos, MINGLE MODULAR PLT_2 STR SHARED ST (Size - 1350 X 600 X 740)-1nos, MINGLE MODULAR PLT_1 STR SHARED ST (Size - 675 X 600 X 740)-2Nos, MINGLE MODULAR PLT 1800W ST (Size - 1800 X 850 X 740)-1No Accessories - Dsk 2 way Name Plate, Dsk Mod Doc Shelf, Dsk HDMI wire Man (One packet Contain 8 Qty)-1No. The rate shall be quote as per the image mention in volume-I.

First Floor - Conference Hall Officer Chair - PULSE Hi BACK (Mb Seat, Adj, Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX,PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE){PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm. The complete neckrest assembly is retro fit to the main chair. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Co-Working Space Work Station Table Providing and placing UPBEAT DESK based modular workstation with System ht - 1200mm SCREENS: Main Fabric screen on stud. UNDERSTRUCTURE: Comprising of metal cross member between legs, DFINE PLUS legs made up of metal finish on end and shared leg with wire tray raiser the entire assemply is fixed to the worktop. Wire Management : Shared leg with wire tray raiser is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s wire tray assembly is provided below worktops. MODESTY PANEL: Porforated metal modesty 0.8 mm thk.modesty is mounted under neath the worktop with the help of the brackets. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w X 600 mm d. Pedestals- Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. The rate shall be quote as per the image mention in volume-I.

First Floor - Co-Working Space Officer Chair - PULSE Hi BACK (Mb Seat, Adj, Arms Larger Seats) 1.SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ± 0.1cm thk. hot pressed plywood measured. The Back is made up of injection moulded glass filled polypropylene & upholstered using Net fabric with high tenacity yarn. *SEAT SIZE (Larger Seat Depth) {PULSAL}: 47.0 cm. (W) x 51.5 cm. (D) *BACK SIZE (PULSAX,PULSAL): 45.0 cm. (W) x 65.3 cm. (H) 2.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m3 and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. 3.ARMRESTS (ADJUSTABLE){PULSAX, PULSAL}: The adjustable armrest is designed with the following features: •Up-Down adjustment- 6 steps (7.2 ± 0.5cm range), Armrest top is mounted on Armrest structure made of glass filled Nylon. •Armrest Top is PU moulded over glass filled Nylon insert. 4.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. 5.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. •360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. •4-position locking with anti-shock feature. - Seat/back tilting ratio of 1:2. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. 7.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors). 8.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm. The complete neckrest assembly is retro fit to the main chair. Overall Dimensions of Chair - WIDTH (W): 76.1 CM, DEPTH (D): 76.1 CM, HEIGHT (H): 98.0 - 108.0 CM SEAT HEIGHT (SH): 45.8 - 55.8 CM. The rate shall be quote as per the image mention in volume-I.

First Floor - Breakout Space Round Table Wooden Table made of 25mm Thickness Solid Wood With MS Black Powdered Coated Base With Size - 4ft Dia. The rate shall be quote as per the image mention in volume-I.

First Floor - Breakout Space Chair 4Nos - The rate shall be quote as per the image mention in volume-I.

First Floor - Dining Area Dining Table : Length : 210cm Width : 97cm Height : 75.5cm Under structure: Made out of first quality rubber wood without knots & defects on all faces. Legs frames are connected with SS-202 cross members. Table also has shelf which is made of MDF (12mm thick). Finish: Chocolate (Indoline shade) with P.U. coat of Hardness 4H on all faces of legs. Cross members are mirror finished. Shelf has membrane (Indoline make) with shade of white cedar exclusive (PVC membrane). Top: 12 mm thick frosted & toughened glass. Assembly, joinery & Hardware: Knock down assembly with high quality standard hardware (Dining Table -1Nos with Chair -8Nos). The rate shall be quote as per the image mention in volume-I.