Tamil Nadu Road Development Company Limited Tender

Providing and laying 50mm consolidated thick Dense Bituminous Macadam as per design mix using VG30 bitumen for premixing including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to work site, spreading the mix to uniform thickness of 50mm with paver to the specified grades and cross sections and compacted by Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver at site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory / Pneumatic rollers and all other tools and plant required, including all other incidental charges etc., complete as per specification using CMP as per clause 505 of MORTH

Providing and fixing reflective road studs of 'Category A' Raised pavement markers made out of poly carbonate/ methyl methercrylate/ ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro-reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MoRTH circular No RW / NH. 33023/10/97- DO.III dt 11.06.97 . The height, width and length shall not be less than 15mm, 90mm and 100 mm and with minimum reflective area of 13 Sq.cm on each side and the slope to the base shall be 35+/5 degree. Each reflector shall have a CIL not less then values specified in table 2 of said MoRT&H circular. The strength of detachment of integrated cylindrical shanks, (of diameter not less than 19+/-2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 500kg f. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturers recommendation and complete as directed by the Engineer. The marker shall support a load of 13635 kg tested in accordance with ASTM D4280 and confirming to IRC 35-2015 guidelines and MORT&H specification 804 etc., complete

Earth work excavation in all classes of soils and sub soils to full depth or as may be directed except in rock requiring blasting inclusive of shoring strutting, bailing out water wherever necessary and disposal of the excavated earth with a lead of 5 Km from site etc. complete complying with standard specifications of clause 304 of MoRTH and as directed by the Engineer in charge

Providing and laying of Hot Applied Thermoplastic compound 2.5 mm thick including reflecting glass beads @ 250 gms per sqm area, thickness is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes, with all lifts and leads etc complete as per MoRT &H Technical specification clause No.803

Providing and laying Tack Coat over Existing BT surface using 2 Kg of Bitumen Emulsion (RS1) per 10 sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per Clause 503 of MORTH

Painting old CC surface with two coats of synthetic enamel paint of approved quality and colour including through scraping, clean removal of dirt etc complete complying with standard specifications and as directed by the engineers incharge for kerb

Construction of granular sub-base by providing close graded Material as per Grading-3 (Table 400-1), mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density etc., complete as per clause 401 of MoRTH

Providing and laying Prime Coat over WMM surface using 7 Kg of Emulsion Bitumen (SS1) per 10 sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per Clause 502 of MORTH Rev-5

Providing and laying Bituminous Concrete to 40 mm thick as per design mix using VG30 bitumen for premixing including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc. including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory / Pneumatic roller and all other tools and plant required, including all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH