Tamil Nadu Maritime Board Tender

Supplying, fabricating, erecting and Fixing MS Suspended Hanging (10 mm Dia suspended Rod and 25×25×2.6 mm MS Square Tube) Supports for Fixing False ceiling for Passenger Terminal Station as per standard specification and as directed by the departmental officers

Supplying, fabricating, erecting and fixing Hilux (or) equivalent board false ceiling upto a ceiling height of 4.5m from floor level,etc., complying with standard specification and as directed by the departmental officers

Supplying and fixing Fully openable Patch Fitting toughened glass partition and door of ' DORMA' or equivalent with "SM" range Fittings to get a clear height with top & Side Fixed panels. In general the openable/sliding door cum Fixed panel consists of sliding channel with all fitting and Corner Fittings SM1090/91, Top pivot SM1001,Top patch SM1020A,Bottom patch SM1010, with BTS 75 V Floor spring with SS cover plate, Standard Spindle SM1049E, corner lock at top & bottom, Euro profile cylinder with 3 keys, lock strike plate SM1052 , Pull handle(TGDI35025) SS Satin Finish and 12mm thick clear toughened glass as per design and all confirming to manufacturers specification. SS fixtures shall conform Grade SS 304 to BS 7352. The rate shall be inclusive of wastage and necessary hardware's etc; as required for complete the works

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 2.70 mx 2.10 m.The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 4 mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column, masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be got approved by Executive Engineer before use

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Aluminium Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete. Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.