Tamil Nadu Generation And Distribution Corporation Limited Tender

Dismantling the existing damaged brick cupboard,shelves, removing the doors and clearing the debris away from the site including cost of all the materials, labours, lead, lift, etc., complete.

Providing P.C.C 1:2:4 using 12 - 20 mm HBS to the damaged ceiling, lintel including cost of all the materials, labours, lead, lift, etc., complete.

Plastering the ceiling with CM 1:3- 12 mm thick with water proofing compound including cost of all materials labour lead lift etc complete.

Plastering the wall with CM 1:5- 12 mm thick with water proofing compound including cost of all materials labour lead lift etc complete.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification 1868/1962 / and should be got approved by Executive Engineer before use.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick MDF both side laminated board of exterior grade at bottom and half glazed using plain glass at top with automatic door closure B3538and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Engineer incharge.

Flooring with approved stain free nano polish vitrified tiles 600mm x 600mm x 8mm of approved quality, design & colour (Standard or equivalent make) laid in cement mortar 1:3 - 20mm thick including pointing with same colour cement using 0.4 Kg/Sqm finishing the joints including cost of all materials, labour, lead, lift etc., complete.

Supplying , fabricating and fixing in position Aluminium Anodised natural colour mat finish Two track sliding window in all floors with Aluminium sections of outer Frame bottom 62x37mmx1.50mm at 1.218 kg/m,the Side & Top 62x31.50x1.50mm at 0.778 kg/m,Shutter Top 40x18x1.5 at 0.38 kg/m,Bottom 40x18x1.5 at 0.38kg/m, Side Vertical 40x18x1.50mm at 0.493 kg/m, Vertical locking section 40x29x1.5mm at 0.632 kg/m, with necessary accessories such as rubber beadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials , labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962 for an average anodic film thickness 15 microns etc., complete.

Supplying and fixing of wash basin of size 550x400mm of approved quality Neycer/Parryware with all accesseries including cost of wash basin with pedestal cock fixing with rug bolt and nuts, 15mm dia PVC connecting hose and outlet using 40mm dia PVC waste pipe, CP valve tap etc, complete.

Supply and fixing of solid PVC door with frame made out of rigid thermo vinyl polymer extruded section ofsize 62mmx51mm with 2mm wall thickness,shall be reinforced with special polymeric rods of size 255mmx30mmx25mm and with EPDM gaskets along the frame. The door shutter frame of 40mm thickmade out of one piece moulded rigid thermo vinyl polymer extruded sectionof size 25mmx40mm with 2mm wall thickness is mitered and joinedat corners by stainless steel/ aluminium screws. The infill of the door shutterconsists of a seamless one piece multichamber hollow rigid thermo vinyl polymer sectionof size 762mmx35mm with 1mm wall thickness and with prelaminated glossy finish on either side of door shutter of suitable size including cost of all materials lead lift etc., complete.

Dismantling the existing damaged European water closet and clearing the debris away from the site, cleaning the IB including cost of all the materials, labour, lead, lift etc., complete.

Supply and fixing of European water closet with "P" & "S" trap with double flapped seat coverwith brass hinges and 10 litre capacity PVC low level flushing tank with all internal fittings including cost of all materials, labour lead ,lift etc., complete.

Labour charges for racking out the joints of the pressed terrace tile and cleaning the racked joints with brushes without any loose debris including cost of all materials, labour, lead, lift etc., complete.

Mazdoor I cat

Mazdoor II cat

Pointing the pressed terrace tiles using CM 1:3 mix with water proofing compound including scraping of existing old pointing including cost of all materials, labour,lead,lift etc, complete.

Applying white cement wall putty to the ceiling & wall surface including cost of all materials, lead, lift, etc., complete.

Painting inside & outside walls with two coats of Exterior Emulsion paint over a one coat of primer of approved colour and quality including cost of all matreials, lead and lift etc., complete.

Painting two coats with good quality of enamel painting over a coat of a primer in the steel door including cost of all materials, labour, lead, lift, etc., complete.