Tamil Nadu Civil Supplies Corporation Tender

Supplying and filling in foundation and basement with clean M.SAND in layers of 150mm thick, well watered, rammed and consolidated including watering etc., complete complying with standard specifications and as directed.

CEMENT CONCRETE 1:4:8(one cement, four sand and eight aggregate)using 40mm gauge hard broken granite stone jelly for foundation including de-watering, side shuttering , strutting, wherever necessary including curing etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and filling in foundation with Gravel in layers of not exceeding 150mm thick well watered, rammed and consolidated including watering etc., complete complying with standard specification and as directed.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling with 40mm gauge HBG stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc., complete complying with standard specification.

supplying and filling in basement with wetmix 250mm thick in layers of not exceeding 250mm thick, well watered, rammed and consolidated including machineries for hire and running charges leader 5 Cum capacity, hire charges for tipper,water sprinkler,vibratory roller all labour charges etc., complete complying with standard specification and as directed by the departmental officers.

CEMENT CONCRETE 1:5:10(one cement, five sand and ten aggregate)using 40mm gauge hard broken granite stone jelly for foundation including de-watering, side shuttering , strutting, wherever necessary including curing etc., complete complying with standard specifications and as directed by the departmental officers.

BRICK WORK in cement mortor 1:5(one cement, five sand) using best quality Country bricks of size 8" 3/4"x4 ¼ x 2 ¾ “ for walls including cost of scaffolding curing, finishing etc., complete complying with standard specification and as directed by the departmental officers. In foundation and basement

In Ground floor (Upto 4.50M height)

Above 4.50M height from basement

Supplying and laying of Ready mix M15 grade of concrete having characteristic strength not less than specified in the IS 456 - 2000 using Ordinary Portland cement with minimum cement content of 366 Kg / cum confirming to IS 8112. Coarse aggregate having a specific gravity of 2.60 using 20 mm down graded hard blue granite broken stone jelly and fine aggregate without fly ash as per IS 383 - 1970 (2007) with suitable water cement ratio not less than 0.45 of water quality confirming to IS 456 - 2000 including use of plasticizer of approved make & dosage of required grade at all location and levels with specified high workability as per IS 1199 - 1959 (2004). The initial & final setting time confirming IS 12269 - 1987 (2004) .The admixtures affecting the quality and strength of the confirm IS 9103 - 1979 [ usual admixture - Air entraining & water reducing).

Providing and laying in position, Standardised Concrete Mix M20 Grade in accordance with IS:456-200 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/M3 and mazimum water cement ratio of 0.55, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improvement workability without impairing strength and durability with about (5 Cu.m) 7730 Kg of 20mm machine crushed stone jelly and with about (3.3 Cum)5156 kg of 10-12mm machine crushed stone jelly and with about (4.7 Cum) 7670 kg of sand, but excluding cost of reinforcement gril and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, cutting etc., and Providing fixtures like fan clams in the RCC floor/ roof slabs wherever necessary without claiming extra etc., complete complying with standard specfication and as directed the departmental officers. The coarse and five aggregates to be used should comply with the requirements of 15 Standards. (No separate payment will be made by the Department for the excess usage of materials. In foundation and basement.

In Ground floor (Upto 4.50M height)

Above 4.50M height from basement

Providing FORM WORK for centering the soffits of all reinforcement concrete work including strutting to the required (3 metre) height with mild-steel sheets of size 90cmx60cm 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm laid with country wood joist of average of size 10cmx6.50cm at about 90cm centres with casurina props of 13cm dia at 75cm centre to centre with all nails coir, wedges complete and removing the form work after necessary curing period as directed by the corporations officers. The rates should inclusives of cutting , bending, welding , charges of M.S sheets, M.S. angles etc., Complete Column footing, Plinth beam , top tie beam etc.,

For Plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall etc.,

Rectangular beams and floor slabs, tie beams, lintels, landing slab, loft etc.,

Columns, ratguard slab, curtain slab and sun shades etc.,

Supplying, fabricating and placing in position MS/RTS grills for reinforcement for all R.C.C.works including cost of steel, labour for straightening, bending, cranking, tying grills with 18 gauge galvanized binding wire and placing grills in position complete complying with standard specification and as directed..

Supplying and fixing(under lintel grove) cold rolled ROLLING SHUTTERS of approved quality of 18 gauge 7.5 cm wide cold rolled lathe section in one piece interlocked together with specially designed pipe shaft with adequate number of high tensile steel wire springs of approved quality complete with brackets side guides and arrangements for inside and outside locking arrangements with push and pull operations and pulling back handle with all accessories in best workmen ship and the entire shutter painted with two coats of best quality anti-corrosive paint over one coat of red oxide primer and clear opening of 1.80M width 2.60M height. The rolling shutter shall be placed below the lintel and behind the RCC curtain slab of 7.5 cm thick and 45 cm depth. Each rolling shutter shall be provided with one pair of approved quality of ball bearing complete. Rolling shutter should confirm to I.S.6248-1979and should be got approved by the Executive Engineer before fixing .[This specification consists of the following component materials required for erection of rolling shutter.(1).18 G 3" lathe section 1.90M long-29 Nos. (2)10 G guide channel 2.6Mlong-2 Nos.(3).13 G bottom plate for 1.8M long with angle.(4).M.S.pipe 40mm dia. C'class -2M long.(5).10SWG side plate 13"x12"-2 Nos.(6).2 SWG spring 3" bore. (7).'U'-clamp.(8).ball bearing suitable for 2 1/2 "pipe.(9).18 SWG clip suitablefor 4"lathe.(10).20 SWG M.S.sheet. Etc.

Supplying and fixing of Steel glazed AIR INLET WINDOWs of size 0.6m x 0.6m using extruded angles (Z-section) alround for frame with centre mullion T-section) and shutter with the same Z-section properly fixed with hinges 2 nos. for each shutter. The panel of shutter fixed with G.I. sheet of'18 gauge and necessary locking arrangements including weld mesh cover using weld mesh 25mm x 25mm x 10mm gauge and welded with iron square bars of 10mm size - 3nos. horizontally and 2nos. vertically welded together to form a grill and welding grill to the main frame with 4mm thick and 12mm wide MS flats. The rate is also inclusive of one coat of steel primer and two coats of ANTI CORROSIVE METALLIC paint and quality, 2 nos. 20cm long stays for shutters etc complete (The paint should be got approved by the Executive Engineer before use on work ) The shutters should open inside.

Supplying and fixing steel N-Type VENTILATOR of size 1.20m x 0.60m using extruded angle (Z-section 25mmx25mmx3mm) for outer frames with center mullion (T-section)and with weld mesh of 25mmx25mm 10guage on all three sides ( 2 verticals 1 horizontal) and 10mm size MS square bars horizontally one at top and one at bottom welded to the frames with necessary MS flats of size 20mmx4mm thick and with necessary FRP plain sheets properly fixed with teakwood fillets MS hold fast 20cm long and necessary ring. The rate shall be inclusive of one coat of steel red oxide primer and two coats of anti corrosive paint of approved quality paint (N-Type Ventilator should be got approved by the Executive Engineer before use on works). Undert weld mesh 75x25mm.

Providing and laying in position, Standardised Concrete Mix M20 Grade in accordance with IS:456-200 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/M3 and mazimum water cement ratio of 0.55, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improvement workability without impairing strength and durability with about (5 Cu.m) 7730 Kg of 20mm machine crushed stone jelly and with about (3.3 Cum)5156 kg of 10-12mm machine crushed stone jelly and with about (4.7 Cum) 7670 kg of sand, but excluding cost of reinforcement gril and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, cutting etc., Placing of concrete and surface hardner finishing with power floated and power trawler to obtain the hard surface including provision of expansion joints at 6Metre intervals across the platform by Groove cutting 6mm wide with polysulphide sealant in full depth of concrete etc., The coarse and fine aggregates to be used should comply with the requirements of 15 Standards. (No separate payment will be made by the Department for the excess usage of materials.

Providing and laying in position, Standardized Concrete Mix M20 Grade in accordance with IS:456-200 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/M3 and mazimum water cement ratio of 0.55, including admixture (Plasticizer / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improvement workability without impairing strength and durability with about (5 Cu.m) 7730 Kg of 20mm machine crushed stone jelly and with about (3.3 Cum)5156 kg of 10-12mm machine crushed stone jelly and with about (4.7 Cum) 7670 kg of sand, but excluding cost of reinforcement gril and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, cutting, Placing of concrete and surface hardner finishing with power floated and power trawler to obtain the hard surface including provision of expansion joints at 6Metre intervals across the platform etc, complete complying with standard specification and as directed the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of 15 Standards. (No separate payment will be made by the Department for the excess usage of materials.)

PLASTERING with cement mortor 1:5 (one cement and five sand) 12mm thick including cost of scaffolding, finishing, curing etc., complete complying with standard specification and as directed.

PLASTERING with cement mortor 1:3 (one cement and three sand)10mm thick including cost of scaffolding, finishing, curing etc., complete complying with standard specification and as directed.

Painting the walls with two coats of Interior emulsion paint of first class approved quality and colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed.

Painting the walls with two coats of Exterior emulsion paint of first class approved quality and colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed.

Supplying and fixing in position 100mm x 50mm x 9.4 kg channel for the face of RAT GUARD EDGING SLAB with MS bolts 16mm dia 45cm long at 2m centres forming protection to the loading platform finishing in flush with the slab with C.M. 1:3(one cement and three sand) etc., complete including painting the exposed surface of MS channel with two coats of ANTI-CORROSIVE METALLIC PAINT over one coat red oxide primer etc., complete complying with standard specification and as directed.

Supplying and laying of High profile colour galvalume sheet with combination 55A1:43 4Zn:1:6SI of TCT bent type 0.47mm thick not less than 150 GSM and standard width of 1.06m with yield strength of 550 MPA made from high tensile/ CR sheets of approved quality for roofing with necessary fixing arrangements like 65m abd long hexagonal head screws with EPDM rubber seal etc., complete, complying with standard specification and as directed by the departmental officer. (Test certificate for quality should be furnished on receipt of material at site)

Supplying and laying of High profile colour galvalume sheet ridges 55A1:43 4Zn:1:6SI of TCT bent type 0.47mm thick not less than 150 GSM and standard width of 1.06m with yield strength of 550 MPA made from high tensile/ CR sheets of approved quality for roofing with necessary fixing arrangements like 65m abd long hexagonal head screws with EPDM rubber seal etc., complete, complying with standard specification and as directed by the departmental officer. (Test certificate for quality should be furnished on receipt of material at site)

Supplying and fixing corrugated Poly Carbonate sheet of size 3mx1.06m of 3mm thick on the roof in-between the colour coated Galvalume sheets for proper lighting with necessary G.I screws and EPDM rubber washers, Complying with standard specification and as direct and specified by the departmental officers including cost of loading unloading and transportion charges etc., complete.

Supply and fixing of 40x6mm G.I flat over the Galvalume sheet roofing which is placed on the top of purlin in the longitudinal direction to avoid the lifting of roofing due to wind, the rate inclusive of neccesary G.I screw, Rubber, Aluminium washer with necessary adhesive flashing tap fixed directly over the galvalume sheet, labour charges for fixing, conveyance loading, unloading and cutting, etc. complete for 42m length.

Supplying fabricating, hoisting and erection of ROOF TRUSSES PURLINS AND WIND BRACING with structural steel member like angle and channel iron and M.S.plates for all truss, purlin members including all cutting drilling holes, and welding and fixing of member with necessary bolts and nuts, of approved quality and hoisting, aligning and placing the trusses in position etc., complete the trusses will be manufactured as per the detailed plan. The rate should include the cost of painting with one coat of red oxide primer with two coats of best quality of aluminium paint over priming coat.

Supplying and fixing of Rotary Ventilators over the roof with necessary bolt and nut arrangement to withstand the wind velocity as specified by the departmental officers.(Size 600mm x 600mm).

Supplying and fixing RCC PRECAST Slab of 50mm thick in cement concrete 1:2:4 (one cement, two sand, four HBGS jelly) using 20 mm HBG Stone jelly as per design and specification, including cost of steel rods and fabrication charges cost of moulding, labour charges for finishing, curing, fixing in position etc., complete.

Providing and laying WBM Gr II of 75mm compacted thickness using 1 Cum of 63mm to 45mm IRC metal and 0.24 m3 gravel for blindage for 10 Sqm. for bottom layer including cost and conveyance of all materials from approved quarry to work site and stacking them to departmental gauge for premeasurement, as directed by the department officers including labour for spreading metal and gravel, hand packing to camber watering with all leads for good water slurring and rolling and consolidation by power roller and finishing as per MORD 405 including hire and fuel charges for power roller and water sprinkler and all other tools and plants employed and all other incidental charges etc., complete.

Providing and laying WBM Gr III of 75mm compacted thickness using 1 Cum of 53mm to 22.40mm IRC metal and 0.24 m3 gravel for blindage for 10 Sqm. for top layer including cost and conveyance of all materials from approved quarry to work site and stacking them to departmental gauge for premeasurement, as directed by the department officers including labour for spreading metal and gravel, hand packing to camber watering with all leads for good water slurring and rolling and consolidation by power roller and finishing as per MORD 405 including hire and fuel charges for power roller and water sprinkler and all other tools and plants employed and all other incidental charges etc., complete.