State Industries Promotion Corporation Of Tamil Nadu Limited Tender

Supplying and Filling in foundation and bore holes with "Sand lime mix 1:1 " in layers, well watered, rammed and consolidated etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing and laying in position, Standardised Concrete Mix M 30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for the all RCC items of works but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary without claiming extra etc., complete complying with relevent standard specification and as directed by the the officers. The coarse and fine aggregates to be used should comply with requirements of IS standards. (No separate payment will be made by SIPCOT for the excess usage of materials)

Brick work in CM 1: 5 (One of cement and five of sand) using Chamber burnt bricks of size 9” x 4 3/8” x2¾” (23 x 11.2 x 7cm) in basement including dewatering wherever necessary proper setting, curing etc., complete complying with standard specification and as directed by SIPCOT officers. (For basement and upto plinth beam level)

Brick work in CM 1: 6 (One of cement and six of sand) using Chamber burnt bricks of size 9” x 4 3/8” x2¾” (23 x 11.2 x 7cm) for Superstructure including dewatering wherever necessary proper setting, curing etc., complete complying with standard specification and as directed by SIPCOT officers. ( Inner wall above basement)

Filling in foundation and basement and other similar works with conveyance earth /stone dust in layers of 150mm thick well watered rammed and consolidated etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for vertical surfaces as detailed below with all cross bracings using mild steel sheets of size 90cm x 60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the R.C.C works etc., complete complying with standard specification and as directed by SIPCOT officers. a.For Column footings,plinth beam,Grade beam, Raftbeam, Raft slab etc.,

upto basement plinthe level

Above plinth level

Plastering with CM 1:5 (One of cement and five of sand) 12mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete complying with standard specification and as directed by SIPCOT officers.

Ceiling Plastering with CM 1:3 (One of cement and three of sand) 10mm thick finished with neat cement including providing band cornice, ceiling cornice, curing, scaffolding, etc., complete complying with standard specification and as directed by SIPCOT officers.

Floor Plastering with CM 1:4 (One of cement and Four of sand) 20mm thick finished with neat cement including curing etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels for reinforcement for all floors including cost of binding wire, bending tying etc., complete complying with standard specification and as directed by SIPCOT officers.

PROVIDING ANTI-TERMITE TREATMENT for flooring etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and laying of polished Rajastan Kota Stone slab with machine cut edge of size 600 x600x20 mm with required cement moratar 1:3including Grout joint filler etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing Painting TWO COATS OVER NEW plastered surface with water Emulsion paint with primer etc., complete complying with standard specification and as directed by SIPCOT officers.

Fabricated Mild Steel PEB building structure with drawings & Materials: Scope of work : Fabrication, Sand blasting, one coat Primer painting, Two coats Enamel painting, Fasteners, Bolts, Nuts, Erection,Transport, Labours including all required tools , Machinerys, Consumables related to fabrication, erection & Paintings work etc., complete complying with standard specification and as directed by SIPCOT officers. Materials: MS - HR Plates,Foundation Bolts, Brazzing Rods,Bolts, Nuts,Washers, Primer, Enamel Paints and necessary fittings. Make : Jindal / Sail / Jsw or Equalent

Fabricated G.I.steel C-Purlin with drawings & Materials. Scope of work: Fabrication, Fasteners, Bolts, Nuts, Erection, Transport, Labours - All required tools, Machinerys, Consumables related to fabrication & erection work etc., complete complying with standard specification and as directed by SIPCOT officers. Materials: G.I. C-Purlin (Size -200 x 60 x 20 x 2.0mm), Sag Rods,Bolts, Nuts,Washers and necessary fittings. Make : Jindal / Sail / Jsw or Equalent

Supply and fixing of Pre painted Galvanium roofing sheet, Cladding and Flashing Sheets with drawings & Materials etc., complete complying with standard specification and as directed by SIPCOT officers. Scope of work : Fabrication, Fasteners, Roofing Screws, Erection, Transport, Labours - All required tools, Machinerys, Consumables related to fabrication & erection work. Materials: PPGL Single skin Profile sheets & Flashing sheets ( 0.47mm / AZ 150 / 550 MPA ), Roofing screws,Roofing sealents and necessary fittings. Make : Jindal / Sail / Jsw or Equalent

Supply and fixing of Fabricated G.I.steel Roof Ventilator with drawings & Materials etc., complete complying with standard specification and as directed by SIPCOT officers. Scope of work : Fabrication, Fasteners, Erection, Transport, Labours - All required tools, Machinerys, Consumables related to fabrication & erection work. Materials: G.I.Roof Ventilator (Size -600mm), Alluminium profile sheet base(Size-1600mm),Fasteners and necessary fittings. Make : Jindal / Sail / Jsw or Equalent

Providing and fixing of Hollow metal fire door as per NFPA from Steel Tech or equivalent at all levels from ISO 9001-2000 certified Manufacturer. Fire door should be as per NFPA 80 and NFPA 252. All fire doors should be tested at UL for maximum the rquired rating and should pass both UL10B and UL10C. Pressed Galvanized steel Single /Double leaf to required sizes for approved rating and make shakti met-dor or equivalent which consists of frame, shutter, infill and finish as detailed below. Door frame shall be double rebate profile of size 143 x 57 mm made out of 1.60mm thick galvanized steel sheet (16 gauge ). Frames should be MITERED and field assembled with self tabs. Door frames should be prepared for suitable hardware as scheduled and should have necessary reinforcement to withstand regular wear and tear. All provision should be mortised, drilled and tapped for receiving the hardware. Rubber door silencers should be provided on the striking jamb. All door frames should be provided with SOFIT bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening.Door leaf should be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 1.2mm (18guage) thick galvanised steel sheet. The internal construction of the door should be rigid with steel stiffeners/ pads for receiving appropriate hardware. In addition the door should have infill of honeycomb core or steel fibres as per manufacturer's specification to suit the location of door and also for structural rigidity. All doors shall be factory fitted with labelled type hardwares from DORMA/ INGERSOL or equivalent for fire - Size of Fire Door 2.40 x 2.10 M, etc., complete complying with standard specification and as directed by SIPCOT officers.

UPVC Window - Specification : Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the SIPCOT officers before use on work etc., complete complying with standard specification and as directed by SIPCOT officers.

"Supplying and fixing of rolling shutters with ISI Monogram of required size with Gear operated type made of 18 gauge, 80mm wide rolled MS lathe interlocked throughout their entire length and jointed together by end locks and mounted on pipe shaft with superior flet spring (enclosed on suitable boxes) complete with brackets, side guides and arrangements for inside and outside locking with mechanical devices for operation.The rate should include cost of providing necessary holes in the Masonry/RCC with pipe sleeve of suitable dia to facilate both side operation etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing of Manually operated Rolling grills with ISI Monogram including painting on both sides etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying and laying 80 mm thick mix vibro compacted heavy duty road paver interlocking block with super embedded anty skid with texture design meeting their international standard size with Zig Zag design with higher loading capacity rate including cost and conveyance all required materials for sand cushion - 40 mm thick at site and all labour charges for laying, compacting with paver vibrator and all taxes etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing Rain water harvesting pit of 1m dia and 600mm depth and filling the pit with 40mm stone jelly to a depth of 300mm from the top of the augering portion and filling with filling sand to a depth of 300mm over the stone jelly and covered with the pre-cast RCC perforated slab of 40mm thick excluding the cost and fabrication of reinforcement grills but including precasting, moulding, curing, finishing and fixing in position etc., complete complying with standard specification and as directed by SIPCOT officers.

Augering 30cm dia bore hole - 1 m depth in all soils and sub soils required depth to providing rain water harvesting from the centre of the rain water harvesting pit already excavated and filling the augering portion with 40mm size stone jelly etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing of 110mm dia PVC SWR pipe with ISI mark confirming to IS 13952:1992 Type 'A' for Rainwater Down fall pipe with relevant specials such as gratings, shoes, bends, offsets confirming to IS 14735 including jointing with seal ring confirming to IS 5382 with leaving a gap about 10mm to allow thermal expansion with necessary clamps, teak wood plugs etc., of approved quality and including fixing CI gratings at the junction of parapet and floor or roof slab including finishing etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and fixing of water CO2 stored pressure type - 9 Litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, Gun Metal cap, Pressure gauge, Operation sticker, discharge hose, wall mounting bracket, safety clip as per FIRE dept. norms etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing in position Indian water closet Oriya type of size 580x440mm white glazed earthen ware of approved quality with ‘P’ trap or ‘S’ trap conforming to IS: 2556-part XII with sand cushion and forming flooring all-round the closet using 40mm broken brick jelly in lime concrete 1:2:5(one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes by dismantling brick masonry, reinforced cement concrete roof/ floor slab and making good the dismantled portion to original condition without leakage, birck work in cm 1:5 for cross wall etc., complete complying with standard specification and as directed by SIPCOT officers. (The water closet should be got approved by SIPCOT officers before use on work.)

Supplying and fabricating and fixing MS grill gate/MS Angle of various sizes including priming coat as per type design drawing given by SIPCOT and as directed by SIPCOT officers.

Supply and fixing in position best quality PVC Soil/ waste pipes of size 160 mm OD having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever necessary and making good the dismantled portion to the original condition etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and fixing of 2 ply barbed wire fencing including cost of fencing wire and all labour charges for tying etc., complete complying with standard specification and as directed by SIPCOT officers.

Construction of Solid cement block masonry with following size of solid cement blocks with cement mortar 1: 5 including cost and conveyance of all required materials at site and labour charges for finishing work etc., complete complying with standard specification and as directed by SIPCOT officers.

Using 400 x200 x 200 mm for base course

Using 400 x200 x 150 mm above plinth beam level

Supply and fixing in position of RCC precast slab - 50 mm thick using RCC 1:2:4 with 3 to 10 mm HBG jelly, cost of sand, stel fabrication including cost and conveyance of all other required materials and all labour charges for fixing in position etc., complete complying with standard specification and as directed by SIPCOT officers.

Solid panel PVC door shutter with frame SoR 23-24-M 0391

Construction of UG sump (capacity 50000 litres) including other allied water supply works in Kitchen block

Earth work excavation for foundation work in all classes of soils such as hard stiff clay, stiff black cotton soil, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc. except hard rock requiring blasting as per SS 20-B and depositing the same to the place shown by SIPCOT Officers within inital lead and lift etc., complete complying with standard specification and as directed by SIPCOT officers.

For 2.00 m depth UG Sump

For 2m to 3m depth UG Sump

Supplying and filling of stone dust for filling including cost and conveyance of stone dust and all labour charges for filling etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing PCC 1:4:8 using 40mm size HBG ISS stone jelly for foundation concrete including cost and conveyance of all materials at site and labour charges for mixing of concrete, laying, compacting, curing etc., complete complying with standard specification and as directed by SIPCOT officers.

Providing RCC M30 using 20mm ISS HBG including cost and conveyance of all materials at site and all labour charges for mixing, laying and curing etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, fabricating and placing in position of steel reinforcement grills using Fe 415- R.T.S rods for all sizes of reinforcement for all reinforced cement concrete works including cost of steel, binding wire, labour charges for cutting, Fabricating, tying, lifting, placing in position of rods, etc., complete complying with standard specifications and as directed by SIPCOT officers.

Providing centering for soffits for RCC Slabs, beams, including strutting 3 m height using M.S.Sheets of size 90 cm x 60 cm xBG10 and M.S. angles of size 25 mm x 25 mm x 3 mm laid over silver Oak joists of size 10 cm x 6.50 cm (spaced at 90 cm c/c ) etc., complete complying with standard specification and as directed by SIPCOT officers.

Plastering with C.M. 1 : 3 - 10 mm thick inclduing cost and conveveyance of all materials at site and all labour charges etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and delivery of Manhole cover slab of size 0.60m x 0.60m (heavy duty) with frame as per Standard Specification (TWAD) etc., and as directed by SIPCOT officers.

Supplying, and fixing of open well submersible pumpset with duty range of 100 LPM x 40 m head, with ISI mark - IS 14220 with single phase panel board with two level guard and auto start as per TWAD specification including conveyance to work site and fixing in position etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, and fixing in position 1000 litres capacity of HDPE materials ready made SYNTEX or equivalent water tank in places shown by SIPCOT officials including cost and conveyance to work site and fixing in position etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, laying and joining PVC pipes of approved quality and best variety conforming to ISS with ISI mark, of the following size above ground level up to 4 M hight laid properly to alignment including cutting, threading and fixing the required PVC specials but excluding the cost of such specials and fixing to the wall with necessary TW plugs, clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete complying with standard specification and as directed by SIPCOT officers.

32 mm dia PVC pipes - 15 Kg/cm2

25 mm dia PVC pipes - 15 Kg/cm2

Supplying, and fixing in position brass chromium plated Screw down Tap 15 mm dia heavy duty material in places shown by SIPCOT officials including cost and conveyance of all other required specials to work site and fixing in position etc., complete complying with standard specification and as directed by SIPCOT officers.

Internal and External Electrification arrangements

Supply and fixing of 7 Segment - (3 TIER) 3 Phase Distribution Board with MCB 12 way TPMCB sheet steel distribution Boards flush type/surface type fited with bus bars and neutral links with sibgle /three phase MCB outgoings and separate 4 way provision for acomodating One No. 4 pile incoming MCB /Isolator and another seperate 4 way provsion for acomodating One No. of 4 Pole ELCB/RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and seperate provisions for MCB /Isolator (totaaly 12 Nos.) for sub incomers in 3 segments with label holder and provisions for taking up cable for size not less than 35 Sqmm. - TPMCB DB with Metal /Acrylic Door Cover with IP 42 protection. - - 12 ways 3 phase DB - No. of ways Incomer MCB/Isolator - 4, No. of ways incomer ELCB/RCD - 4, No. of sub incomer - 12, No of outgoings ways - 36 etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, erecting, connecting and commissioing 63 Amps 4 pole MCB in weather proof type MS enclosure with necessary adopter boxes, interconnections etc., complete complying with standard specification and as directed by SIPCOT officers - (The box shall have a provision for connecting 4 c x 16 sqmm Alu cable on both sides without any problem).

Supplying, erecting, connecting and commissioing 32 Amps 4 pole MCB in weather proof type MS enclosure with necessary adopter boxes, interconnections etc., complete complying with standard specification and as directed by SIPCOT officers. - (The box shall have a provision for connecting 4 c x 16 sqmm Alu cable on both sides without any problem).

Supply and fixing of 20 A DP plug and socket in sheet enclosure witjh 32 A DP MCB in flush with wall with earth connections (For AC Plug ) etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and fixing in position of following electrical fittings with approved brand etc., complete complying with standard specification and as directed by SIPCOT officers.

20 W LED tube light fittings

48 " Ceiling Fan with electronic regulator - SD No. 107

450 mm dia Exhaust fan with wall opening and making good - SD No. 118

200 W LED dome light fitting

150 W LED Outer Street light fitting

7W/9W LED Bulb with holder

Wiring with 2x1.5 Sqmm (22/0.3) PVC Insulated unsheathed SC copper conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5 A FT switch inflush with wall covered with Hylum sheet of 3 mm thick painting of suitable colour with continuous earth wire connections of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concelaed Light point/5 A Power plug/ Fan point - (Electronic regulator ) etc., complete complying with standard specification and as directed by SIPCOT officers.

For Light point

For FAN Point

For Exhaust Fan Point

5 A 3 pin and 2 pin combined flush type wall socket with 5 A Flush type switch

Supply and fixing of DUMMY Conduit pipes as detailed below.

MS conduit pipe - 25 mm dia

PVC conduit rigid pipe - 19 mm

Supply and run of 2 of 4 Sqmm (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V in 25 mm dia GI Pipe (class "B") suitably bent at both ends with necessary angle Iron upright and end supports for mains etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying, laying , connecting and commissioing 3.5 C x 95 sqmm Alu. Ug Cable in a trench to be excavated at a depth of 0.75 m putting 0.15 m layer of sand and covering the thre sides of the cable with bricks and refilling the earth to make good etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and fixing of 5 A /15 A 3 pin combined flush type wall socket with 15 A flush type switch concealed in suitble MS box flush type with wall with painting etc., complete complying with standard specification and as directed by SIPCOT officers.

Supply and fixing of 125 KVA Generator set withj Auto main failure (AMF) Panel including all accessories and Silencer pipes etc., complete complying with standard specification and as directed by SIPCOT officers.

Sub Total of Total Amount in Column BA (ie. Qty x Unit Rate)

Added GST of 18%