Rural Development And Panchayat Raj Department Tender

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Plastering in CM 1:4 20mm thick including cost and conveyance of all materials and labour charges etc. complete

Supplying & fixing with cuddapah slabs 38 / 40mm Thick for cup board thick and pointed with cement mortar 1:3 -10 Sqm etc completed

Service connection bearer wire

Towards labour charges for Fixing Window

Finishing the top of roof with one course of PRESSED TILES of size 20 cm X 20 cm X 2 cm laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to I.S. at 2% by we

Window - W

Painting two coats with ready mixed paint including cost and conveyance charges etc.

Ventilator - V1

Dadooing walls with glazed tiles of size 0.15 x 0.15 set with CM 1:3, 10 mm thick etc., complete

Towards the Cost & Supply Of Indian Water Closet White

Plug Point (3x3)

Supplying and fixing P.V.C rainwater down fall pipe of 110mm dia with necessary shoes, bends,& clamps etc.,

Supplying & Fixing of Tube Light

Supply and fabrication of steel for RCC works including cost and conveyance charges etc

Exterior Emulsion painting two coats with best approved quality and colour paint over one coat of Base coat including cost and convyance of all materials to work site and labour charges etc., complete.

CFL at toilet

Brick work in CM 1:5 mix using country Bricks including cost and conveyance labour charges etc.

CFL Bulk Head

Above GL

Power Plug

Provision for Ground level earthing

Meter Board

Cost and Supply & Fixing of Fan

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing,laying and curing etc complete

Supply and errection of steel centering for RCC works using MS sheets and angles and strutting upto 3.00 in height including cost and conveyance of all materials to site and all labour charges etc complete

Construction of Multi Purpose Hall at Paneerkulam Village and Panchayat

Fan Point

Filling River Sand including cost and conveyance loading unloading from approved quarry to work site and labour charges for filling, ramming, etc. complete

RCC 1:1/2:3 mix using 20mm metal including cost of all other charges etc., complete

Light point

Provision for Electrification arrangements

Service connection Pipe 20mm

Below GL

Brick jelly Lime concrete by using 20 mm brick jelly with lime in the ratio of 32 : 12.5 including cost conveyance of all materials and labour charges for mixing laying compacting well beaten with wooden batens etc complete

16A DP Switch

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package} 18%

Earth work excavation and depositing on bank with initial lead and lift in Hg soil for foundation etc. complete.

Supplying and applying of two coats of putty of 3 mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinting machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for alteast 48 hrs. Its shall then be sand papered the same after dry and finishing the surface smoothly, etc complete complying with sandard specifications and as directed by the departmental officers (the rate are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet) cost of Putty blade labour charges gor grinding the joints and sand papering,two coat of Putty scrapping the putty area to level the surface smooth,etc complete. Theputty should be got approved by the executive engineer before use on work(based on SOR (2023-24)

Towards the Cost & Supply Of European Water Closet White

Towards labour charges for Fixing Doors