Rural Development And Panchayat Raj Department Tender

Towards centering charges inclusive of all materials and labour charges etc., complete as per standared specification

Plain cement concrete in C.C.1:3:6 mix using 20mm ISS HBG Metal including cost and conveyance of all materials to site and all labours etc., complete

Plain cement concrete in C.C.1:2:4 mix using 20mm ISS HBG Metal including cost and conveyance of all materials to site and all labours etc., complete

Plastering with cement mortar 1:4 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 Sqm

Provision for Tarpad

Provision for Name Board

2)Construction of Threshing Floor Karambiyam road SF.No:78/2 @ Elanthankuzhi Panchayat Panchayat. Earth work excavation in hard gravelly soil with initial lead and lift as per SS20 B for Foundation in narrow trench.

Supplying and filling in foundation, basement, etc with filling Crushed stone sand(M.Sand) in layers of not more than 15 cm thick well watered, rammed and consolidated etc., complete.

Plain cement concrete 1:4:8 mix using 40 mm ISS HBG metal including cost and conveyance to site and all labour charges etc ., complete.

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,

Supplying and erection centering for sides and soffits inculding cost and conveyance of all materials to site and all labour charges, etc., complete.

Towards cost supply and fixing of 50mm dia GI pipe including cost and conveyance of all materials to site and all labour charges etc complete

Roofing with roof ridge sheet standard accessories Colour coated A1 Zn alloy coated steel (550 Mps) 0.50 mm TCT Conveyance loading, unloading best quality using J or U clamps with bitumen washers etc., complete as per standard specfication., etc., complete.

Plain cement concrete in 1:3:6 using 40mm ISS HBG metal including cost and conveyance of all materials to site and all labour charges, etc., complete.

Plain cement concrete in 1:2:4 using 20mm ISS HBG metal including cost and conveyance of all materials to site and all labour charges, etc., complete.

Brick work in cement mortar 1:5 mix using country bricks 83/4"x41/4"x23/4" and conveyance of all materials to site and all labour charges etc., complete.

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and labour charges for curing etc.,Complete.

Provision for Tar Pad Inculding Cost and conveyance of all materials to site and all labour charges etc complete.

Provision for Name Board

3)Construction of PDS Shop Type-I @ Elanthankuzhi Panchayat. Earth work excavation in all classes of soils except hard rock requiring blasting depositing on bank with initial lead of 10M and lift of 2M including all labour charges and incidental charges such as shoring, strutting, providing coffer dams, bailing out of water etc

Supplying and Filling foundation and basement with filling sand in layers not more than 15cm . Thick well rammed, watered and compacted Complete complying with standard specification.

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Filling in Basement with conveyed earth in layers of not more than 15cm. Thick well rammed, watered and consolidated complying with standard specifications etc., complete.

Brick work in CM 1:5mix using country bricks ground molded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. For foundation and basement

For superstructure in ground floor

Supplying and Fabricating and placing in position MS steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with standard specification.

Supplying & Erecting centering for sides & soffits including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casuarinas props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items Centering below Ground level

Rate for column post

Rate for Grade beam,Lintel

Rate for Roof beam ,Slab

Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcemeat and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary and bearing surfaces of walls , sides and bottom of the slabs, beams etc., shall be finished smooth with cement mortar 1:3, 12mm thick. and with Kraft paper without claiming extra as directed by the departmental officers complete complying with standard specifications For foundation and basement

For superstructure in ground floor

Paving the Top of roof with Solar reflective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three M.Sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Supply and fixing of Cuddapah slab including cost and supply of work site etc complete.

Finishing the exposed surface of RCC item of work such as slabs, beams, sunshade, facial, canopy slab, staircase waist slab, landing slab etc., with CM 1:3, 10mm thick. including raking the surface. The rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps, landing slabs etc., complete complying with standard specifications.

Plastering with CM 1:5,12mm thick. over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers.

Granolithic Floor finish 1:2:4 mix of 40mm thick HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Paving the flooring with special type of flooring tiles (Cement based Hydraulically pressed Anti skid tiles (20mm thick) in CM 1:3, 20mm thick complying with the standard specifications and as directed by the departmental officers.

Dadooing walls with Glazed tiles of any color and any size laid in CM 1:2, 10mm thick. and pointing with white cement 0.4 Kg per sqm mixed with coloring pigment to suit the color of the tiles including finishing the joints neatly complying with the standard specifications and as directed by the departmental officers. The Glazed tiles should be got approved from the Departmental officers before execution.

Distempering two coats with best approved oil bound distemper including cost of painting priming coat over new plastered surface and conveyance of all materials to site and all labor charges

Exterior Emulsion Two coats over priming coat including cost and conveyance of all materials and labor charges etc complete.

Painting two coats over new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with best approved best quality of synthetic enamel paint of approved color over the existing priming coat etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fabrication of the following rolling Shutters including cost and conveyance and all charges etc complete.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,

Supplying and fixing PVC sliding door with Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames, 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter including slidng arrangements.

Fabricating, Supplying and fixng in position of steel sheeted windows ( Two Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.

Fabrication, supply and fixing in position of 'N' type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm 'T' section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising as directed by the departmental officers.

Supply and fixing of 15 A Aerial Fuse unit (500A) unsuitable 100 x 100 Teak Wood Board Concealed box Using Clamps SD-128

Supply and fixing of 16 Amps DPIC switch of 500V grade with Fuse and Neutral on suitable T.W. board with painting of suitable color with PWD Earthling (SD No.154)

Supply and run of 2 of 6 sq. mm ( 84/0.30) polythene insulated and PVC unsheathed S.C. Alu cable of 1100 V on 7/20 Gi bearer wire for Service Connection Main - SD.64

Supply and run of 2 x1.5sq. Mm(22/.3) PVC insulated SC unsheathed CU. Conductor of 1100Grade in 25mm Dia GI PIPE (Glass"B")suitably Bent at both ends with necessary angle iron upright and end supports for Mains SD 69

Supplying and fixing of CFL including all cost and conveyance to work site etc complete

Supply and fixing of W.T. Bulk head fitting complete with guard suitable for lamp with 40 W bulb with PVC unsheathed leads from terminal to the fitting - SD. 83

Wiring with 2 x 2.5 Sq.mm PVC unheated SC allocable of 650V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with T.W. Switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable color for Concealed PVC light point / Fan Point SD 25

Wiring with 2 x 2.5 Sq.mm PVC unheated SC allocable of 650V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm T.W. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 Amps 3 pin non - interlocking C.S. Plug top with painting of suitable color for open PVC plug point.- SD -36.

Supply and Fixing of Ceiling fan including cost and conveyance of all materials and labor charges etc complete.

Wash basin

IWC For Toilet

EB Service connection

Provision for Name Boards including all charges etc complete

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}