Rural Development And Panchayat Raj Department Tender

Supplying and filling the foundation and basement with earth in layers of not more than 15cms thick, well rammed, watered and consolidated etc. complete complying with standard specification as directed by the departmental officers

Cement concrete 1:4:8 (one of cement five of sand and ten of aggregate) using 40mm size hard broken granite stone jelly for flooring including well rammed and rendering the top surface rough to receive the floor finish, curing etc. complete..

Brick work in cement mortar 1:5 (One of cement and five of sand ) using country bricks of size 8 3/4" X 4 1/4" X 2 1/4" including proper setting, curing, shoring and strutting, bailing out water etc., complete in all respects.

Below Basement

Basement to Lintel

Litel to Roof

Supplying and erecting, centering for sides and soffits including necessary supports and strutting up to 3.30m height for the following surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size.90cm.x 60cm and 10 B.G

upto Basement

Lintel and Sunshade

Roof Slab

Reinforcement Cement Concrete 1:1.5:3 using 20 mm ISS HBG metal for all RCC item of works excluding cost of reinforcement and fabricating charges, centering and shuttering but icluding curing and providing fixtures like fan clamps in the RCC floor or roof

upto Basement

Lintel and Sunshade

Roof Slab

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grills for all RCC works as per the design given including cost of steel and binding wire in all floors etc.complete complying with standard specifications.

Plastering the surface of walls with cement mortar 1:5 (one of cement and four of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing 25mm thickness of Granolithic pattern for floor finish with cemernt concrete 1:2:4 ( one of cement, two of sand ,and four of hard broken stone jelly) using 10to 12mm HBG stone jelly on top Surface Shall be rubbed smooth finishing and curing etc

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

STEEL Window Manufacturing, supplying and fixing in position of steel windows with the following specifications. Outer frames of windows made of "Z" section F7D of size 33 x 25 x 3mm at 1.419kg/m and mullion "J" section (F4B) of size 46 x 25 x 3mm at 2.28kg/m and shutter section of made of F7D of 33 x 25 x 3mm at 1.419kg/m as specified in IS 7452/1990. ach openable shutter should not exceed a width of 600mm to enable separate operations and easy maintanenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18 x 5mm MS flat at 0,70kg/m at 3Nos. for each shutter and additional diagonal stiffeners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR sheets in position firmly.

Supply of Steel Window of size 0.90X0.60

White washing the newly plastered wall surfaces with two coats using shell lime icluding all charges etc complete.

Colour washing two coats in all floors using best freshly burnt white shell lime and best quality of approved variety of colouring pigment including cost of lime, colouring pigments, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification. Mineral colouring pigments not affected by lime should only be used (stainers and colour solutions should not be used.)

Painting new iron works such as steel doors, windows,ventilator, with two coats of approved quality and colour of synthetic enamel paint including all charges etc Complete…..,

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 110mm dia 4KSC PVC PIPE

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone M.Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone M.Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Solid PVC Door shutter with frame using 19 gaug 19mm MS sq. tubes for styles and outer frames, 15mm MS sq. tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over a size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. (0.75 *1.8)

Towards supply and delivery of RCC Jolly (20 cm x 20 cm) including cost and conveyance of materails and all labour charges for fixing in position as per std. Specification

Provision for Cudappa Slab20/30mmthick for Shelf 0.90 x 0.30 x 0.025 thk Arrangement including cost and conveyance of materails and all labour charges for fixing in position (Rate as per Page no 17 Sl no 75(III) )

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Provision for Leach Pit Arrangement ( 2 x 3 Nos of 900 mm Dia RCC Rings including cost of materials and fixing charges)

Construction of inspection Chamber 0.45X 0.45X 0.60 m Brick work and inner and outer plastering and Covered with Rcc Cover slab including all labour charges

Supplying and fixing in position best approved of BIS quality PVC Sanitary pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Providing Rain Water harvesting Structure including earthwork excavation and filling with brick jelly ,40mm jally and sand including cost of all material and all labourb acharges

Provision for electrification

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 1.50 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and Fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit on TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit SD125

Supply and fixing for 9W LED Bulb SD80

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}