Rural Development And Panchayat Raj Department Tender

1/0-1/8

Earthwork Excavation for foundation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring and strutting and bailing out water wherever necessary and refilling the side of foundation with excavated earth in layers of not more than 15cm thick, well rammed and consolidated and depositing the surplus earth in all places shown by the departmental officers with initial lead and lifts etc. site etc complete complying with standard specification and as directed in sand, silt and loose soil, wet sand and silt not under water light black cotton soil, sandy loam and ordinary soil including excavated earth as per SS20A KM 0/0-1/8

0/0-1/0

1/0-1/8

Providing and Laying Gravel Soling to compacted thickness including cost & conveyance of gravel from approved sources to work site including labour for spreading, watering and compacting by Power roller to achieve the required Proctor density at 100% compaction at optimum moisture content and hire & fuel charges for power roller , water sprinkler and all other incidental charges such as traffic barricading and providing danger lights etc, complete. KM 0/0-1/8

0/0-1/0

1/0-1/8

Picking the existing mettalled BT surface up to 50-100mm deep etc, including all labour charges etc., complete complying with standard specifications and as directed.. KM 0/0-1/8

0/0-1/0

1/0-1/8

Providing 75mm consolidated thickness WBM for bottom layer using 1 cum of grade II metal of 5% of 75mm, 45%of 63mm, 42.5% of 53mm and 5% of 45mm ,2.5% of 22.4mm IRC size HBG metal 0.24 cum of gravel whose PI values is less than '6' for blindage and filler for 10 sqm. area (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 20 & 6% respectively) including cost and conveyance of all materials from approved quarries to road side and stacking of materials to departmental standard metic gauge for pre - measurements including labour for laying,spreading new metal, hand packing to camber gravel blinding, watering with all leads of good water even if the season is worst drought forming edge bunds and consolidation by 8 to 10 tone power roller and finishing to the total thickness with lines grades and cross sections as specified in the departmental specifications including hire charges for all T&P fuel cost and other running charges for power roller and other tools and plants employed and all other incidental charges etc., complete. SSRB 203-05,203-03,502 MOST 401,402 0/0-1/8

Providing 75mm consolidated thickness WBM for top layer using 1 cum of grade III metal of 2.5% of 63mm, 20%of 53 mm, 72.5% of 45mm and 2.5% of 22.4mm ,2.5% of 11.2mm IRC size HBG metal 0.24 cum of gravel whose PI values is less than '6' for blindage and filler for 10 sqm. area (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 20 & 6% repectively) including cost and conveyeance of all materials from approved quarries to road side and stacking of materials to departmental standard metic gauge for pre - measurements including labour for laying,spreading new metal,hand packing to camber gravel blinding, watering with all leads fro good water even if the season is worst drought forming edge bunds and consolidation by 8 to 10 tone power roller and finishing to the total thickness with lines grades and cross sections as specified in the departmental specifications including hire charges for all T&P fuel cost and other running charges for power roller and other tools and plants employed and all other incidental charges etc., complete. SSRB 203-05,203-03,502 MOST 401,402. KM 0/0-1/8

0/0-1/0

1/0-1/8

Applying tack coat over WBM surface using 4Kg of bituminous emulsion per 10sqm including cost of bituminous emulsion which will be supplied departmentallly at section stores and cost of which will be recovered at the rates as per special conditions appended herewith including conveyance of bituminous emulsion to actual work spot handing charges including labour charges for brushing cleaning and preparing the surface for laying the tack coat and labour and machinery charges for applying the required quantity of bituminous emulsion including hire fuel and running charges for all tools and plants employed for the work including all other charges such as barricading and providing danger lights flags etc., complete. KM 0/0-1/8

0/0-1/0

1/0-1/8

Providing and laying open graded premix carpet of 20mm compacted thickness using IRC size machine broken HBG metal 0.18 cum, 13.2mm and 0.09 cum of 11.20 m with 13.432 kg of bitumen and 1.168 kg of Plastic Waste for premixing for 10sqm of premix carpet and 0.09 cum of 6.7 mm IRC size HBG metal with 9.80kg of bitumen for 10sqm for seal coat including cost and conveyance of all materials from approved quarry to work site and stacking them to departmental gauge for pre measurement including cost of bulk bitumen the rates specified in the special conditions appended herewith and including conveyance of bitumen to work spot handling charges for the same at both ends including labour charges for heating the bitumen to required temperature and mixing the required quantity of metal and bitumen using Mini Hot Mix Plant conveying the mix by wheel borrows including labour charges for spreading the mix to grades, lines and profiles and compacting with power roller rolling etc., including all labour charges application of bitumen for seal coat and power roller rolling separately as per MoRT & H specification 509 and 513 including all incidental charges such as barricading providing danger lights etc., complete KM 0/0-1/8

0/0-1/0

1/0-1/8

Supply and fixing of KILOMETRE STONE (three faces two lines dressed) of size 1.65 x 0.45 x 0.15m from approved sources including cost and conveyance to work site and fixing in position as directed by the Departmental Officers including labour and all other incidental charges etc., complete.

Supply and fixing of HECTOMETRE STONE (three faces two lines dressed) of size 0.75 x 0.23 x 0.10m from approved sources including cost and conveyance to work site and fixing in position as directed by the Departmental Officers including labour and all other incidental charges etc., complete.

Fabrication and Supply of Information Name board of size 1200mmx900mmx43mm gauge with Leg channel of size 100mmx50mmx3mm and 3.6 mm long including painting the whole unit with one coat best quality primwr and two coats with approved color sinthetic enamel paint over the primer and lettering as per the Engineers instruction, design and specification etc.complete

Providing and Fixing of Retro Reflectorised cautionary mandatory and informatory sign (with or with out definition board) made out of high indencity prismatic grade sheeting confirming ti IRC 67-2010 and ASTM D 4956- 09 type IV Specification and fixed over 1.50mm thick aluminium Sheet fixed on back supporting frame of 25mm x 25mmx25mmx 3mm miled steel angle and supported on a miled steel angle iron post 75mmx75mmx6mm Firmly Fixed to the ground by means of properly designed foundation with M15 grade Cement concrete 45cm x 45cmx 60cm, 60cm below ground level etc complete including 5 year warrenty for the rectro reflective sheeting Retro - Reflectorised traffic signs ( With definition Board)

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}