Public Works Department Tender

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Renewing and refixing the damaged aluminium anodized natural colour matt finish fully PLB partition with 63.50 x 38.10 x 1.28mm extruded box section at bottom, vertical and horizontal members. The vertical members are spaced at 80mm centre to centre to horizontal members are spaced at 0.80M, 1.60M and 2.40M height from the floor level. Panels should be covered with 9mm thick both side PLB exterior grade with necessary accessories like rubber beedings, aluminium clips, screws etc. The aluminium surface is to be anodized with matt finish under electrically controlled condition in accordance with ISI 1868 / 1962 specificaitons for an average wall thickness of not less than 15 microns. The rate is inclusive of cost of materials, conveyance, scaffolding charges if any required etc and necessary dismantling making holes in RCC (or) masonry works with power drill and redoing the same to the original condition after fixing the partition etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing of New Aluminium doors fully PLB without frame by using anodized natural colour matt finished aluminium door and 9mm thick novopan board including necessary assessories like aluminium clips, rubber beedings, door handle, door closer, furniture fittings, screws etc., and also inclusive of labour charges for fixing of door etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing Health faucet with Two way bib cock tap with flexible hose 15mm dia parryware of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Renewing and fixing Angle Cock with new one of approved quality Metro or Equal Brand and approved make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing position CI Nahani Trap / Floor Trap of the100 x 75mm sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Renewing the damaged wall panelling using 2"x1" Aluminium Channel 2"-0" intervals on single directed and fixing to the existing wall portion and fixing 8mm thick anti termites water proofing plywood using screws etc., and finishing with 1mm thick special texture super matt laminate sheet of approved quality and colour with grooves using fevicol etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Renewing and laying and jointing UPVC Pipe(Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance.(schedule-40) but excluding cost of such specials and fixing in position dismantling masonry and make the same to original condition etc complete complying with standard specification and as directed by the departmental officers at site of work.

20mm dia upvc

Renewing and refixing following UPVC/CPVC special of approved aulity and make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Elbow

Tee

coupling

Reducer

FTA

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

63mm dia pvc

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

Elbow 75mm dia

Supply of best quality and approved make following carpentary material as directed by departmental officers.

Door Closer DYNA make

Door stopper

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Reconstruction of damaged Manhole chamber of following with a base concrete of by new on of a base of concrete of Plain cement concrete 1:5:10, 10cm thick over a 10cm sand cushiion & brick work in CM 1:5 for chamber wall with 20mm thick 1:3 CM plastering for walls flooring including cost of labour charges curing cost of sFRC cover slab of size 0x60x0.60 including labour charges for fixing the slab inposition etc.,

Paving the floor with fine polished cuddapah stone slab of 20/30mm thick laid over Cement Mortar 1:3 (One Cement and Three Sand) 20mm thick over the existing bed of Cement Concrete 1:5:10, (One Cement, Five Sand and Ten aggregate) and pointing the joints to full depth of slabs with same mortar mixed with black oxide and the top surface rendered smooth, curing, etc., The cuddapah stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete complying with standard specification.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying storage unit of size 900mmx2400 (H) and 450mm width fabricated out of 18mm thick water proof plywood and top sides and port portion with laminated with 1mm thick including finishing neatly edges laminated with 2mm thick PVC beading with swing type door providing hinges hand lock and painting interior portion with 2 coats of SEP over primer etc., complete complying with standard specification and as directed by the departmental officers.

Supplying storage unit of size 900mmx450mm x1250 (H)and 450mm width fabricated out of 18mm thick commerical plywood finishing duly edges banded with 2mm thick PVC beading with swing type door providing hinges, lock & key arrangement and painting interior portion with 2 coats of SEP over primer etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of table of size: 1200mm X 600mm X 750mm(H)- 25mm thick particle board duly postformed edge with flex laminate. Leg & Modesty panel 18mm thick prelaminated particle board. Mobile pedestal of size 400mm x 450 mm x 640mm (H) - gabricated out of 18mm thick prelaminated particle board duly edge banded. Having 2 drawer one filing drawer.

GST at 18%