National Bank For Agriculture And Rural Development Tender

c) 90 cm equilateral triangle (Pedestrian Crossing ahead)

d) 90 cm high octagon (STOP)

e) 60cm circular (overtaking prohibited)

f) 60 cm circular (Speed Limit))

g) 60 cm equilateral triangle (Speed Breaker Ahead)

h) 60 cm equilateral triangle ( Roundabout)

i) 60 cm x 45 cm rectangular (Facilities information sign board)

j) 60 x 45 cm Chevron Sign boards

k) 60 cm equilateral triangle ( Gap in Median)

Hazard marker Traffic signs - Type - IV

Providing and erecting of Retro Reflectorised hazard marker traffic sign made out of High Intensity Prismatic de Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge High intensity Retro Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall he obtained as per IRC 67:2012-(as per MORT&H Specification No 801)

30cm x 90x cm One Way Hazard Marker (Object Marker at culverts facing)

Direction and Place Identification signs type XI

Providing and erecting of Direction and Place Identification Retro-Reflectorized Sign made out of cube corner Micro Prismatic grade sheeting of type XI standards of IRC 67-2012 and ASTM D 4956-09 specification, and fixed over 2mm thick aluminium sheet fixed on back supporting frame of size 25mm x 25mm x 3mm mild steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge micro prismatic grade Retro Reflection sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.9 of IRC 67-2012. The retro reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall he obtained as per IRC 67:2012- (as per MORT&H Specification No 801) (for location of black spot, sharp curve, bend, junction, ghatroads and critical zone applications)

Direction and Place Identification signs more than 0.9 sqm size board(1.5m x 0.9m)

Road Markings

Providing and laying of hot applied thermoplastic compound 2.5 mm. thick including reflectorising glass beads @ 250 gms. per sqm. area, thickness of 2.5 mm. is exclusive of surface applied glass beads as per IRC: 35. The finished surface to be level, uniform and free from streaks and holes etc. complete. (as per MORT & H specification No.803). (Annexure - II to Minutes of Meeting of the Board of Engineers held on 24.09.2021)

Lane, Centreline, Edge and other marking along strips, Hazard Marking, Pedestrain marking, stopline, Junction marking, Directional arrows and letters

Road Delineators

Supplying and installation of delineators (road way indicators, hazard markers and object markers), 80-100 cm high above ground level, painted at alternatively black and white in 15 cm wide strips,fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 etc., complete (as per MORT&H specification No.806)

At Junctions

Reflective Pavement Markers (Road Studs)

Providing and fixing reflective road studs of category-A raised pavement markers made out of poly carbonate/methyl methecrylate/ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectane and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular no RW/NH.33023/10/97-DO.III dt 11.06.97. The height, width and length shall not be less than 15mm, 90mm and 100 mm and with minimum reflective are of 13 sq.cm on each side and the slope to the base shall be 35+/- 5 degree. Each reflector shall have a CIL not less than values specified in table 2 of said MORTH circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19+/-2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 500kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635/ Kg tested in accordance with ASTM D4280 and confirming to IRC 35-2015 guidelines and MORT &H specification 804 etc. complete.

Reflective Road studs

Metal beam crash barrier type A W Double Gaurded

Cantilever Gantry Informatory Sign Board

Providing and fixing Digitally printed Retro-Reflectorized Cantilever Gantry Informatory Sign Board made out of cube corner Micro Prismatic grade sheeting of type XI standards of IRC 67-2012 and ASTM D 4956-09 specification, and fixed over 2mm thick aluminium sheet fixed on back supporting frame mild steel L angle of size 50mm x 50mm x 6mm. The vertical support post for the installation of overhead sign gantry shall be made of 300 NB (Nominal Bore) MS pipe with 12mm thick with a ground clearance of 6 metres along with 80NB (Nominal Bore) MS pipes with 4mm thick and 40NB (nominal Bore) MS pipes with 3.20mm thick support posts. MS Base Plate of size 1200mmx 1200mm x25mm MS Top plates of size 900mm x 900mm x 16mm to be used. to hold the sign board at the bottom and top respectively.MSstiffener plates 8mm thick of sizes 420 x 420, 682 x 420, 288 x 288, 288 x 927 & 44 x 130 are to be used. Anchor bolt of dimension 25mm dia and 1000mm length are to be used as fixtures. The approved direction information should be digitally printed and should have 70% of the co- efficient of retro -reflection values against the values as mentioned in talble 6.9 of IRC 67b -2012. The latex printer used for digital printing should use inks with low VOC emissions and should have green guard, eco logo certificates as per UL 2801 standards The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three year outdoor exposure report shall be obtained as per as per IRC 67-2012 (As per MoRt &H specification No.801). Cantilever sign shal be installed at the site as per approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment , Machineries to work site, including all labour charges for fixing the gantry in position with all lead and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer - in charge etc., complete

Cantilever Gantry Informatory Sign boards

Providing and erecting single side double guard metal beam crash barrier system 1.70m high, comprising of 3mm thick wall W beams post and spacer channels shall be made byhigh, comprising of 3mm thick wall W beam post and spacer channel shall be made by cold roll forming using HR conform to IS 5986 Fe 410/360 and dip galvanised having zinc mass of 550 gms /sqm, minimum 950m above road/ground level fixed on ISMC series channel vertical post 150 x 75 x 5 mm spaced 2m centre to centre 312mm x 83mm flange width x 3mm thick, 4318mm long post directly embedded in the concrete (M15) pit size 350 x 350 x 800 mm for a depth of 750mm below ground. All fixing bolts and nuts hot dip galvanized confirming to IS 1367 clause 4.60 all complete as per technical sanction and as directed by the engineer in charge

Single side double guard metal beam crash barrier at Km 1/8, 2/2, 2/4 Required location

Calculation of SubTotal, GST and Total carried out by system automatically

Sub Total Amount for above all items (excluding GST)

GST 18% for above SubTotal Amount

Total in Figures (SubTotal + GST)