Municipal Administration And Water Supply Department Tender

Providing and laying 50 mm compacted thick dense bituminous macadam using 0.24 cum of 26.5-13.2 mm graded metal and 0.25 cum of 13.2-2.36 mm graded metal and 0.23 cum of 2.36 mm & below metal with 53.20 kgs of 60/70 bitumen for premixing per 10 sqm including cost and conveyance of all materials to C M P site, heating the bitumen and agregates to required temperature and mixing them in required temperature in central hot mix plant 20- 30 tonnes capacity conveying the mix by tipper trucks to paver site,spreading the mix in required temperature for uniform thickness of 50 mm with mechanical paver to the specified grades and cross sections and compaction by 80-100 KN power roller to the required density etc.,including labour charges for loading bitumen in to bitumen tank and metal to feeder unit,labour for attending to paver site etc., including hire charges and fuel charges for 20-30t C M P with bitumen boiler,tipper trucks,paver finisher, power rollers and all other tools and plants required,including all other incidental charges etc.,complete using C M P clause 505 of MORTH Rev-5 specifications.

Providing and laying Bituminous concrete to 30mm thick using 0.13 cum of 19.00-9.50 mm graded metal and 0.17 cum of 9.50-2.36 mm graded metal and 0.26 cum of 2.36 mm & below metal with 45.27 kgs of 60/70 bitumen & 5.03Kg of Plastic waste (Total-50.30 kg) and for premixing per 10 sqm including cost and conveyance of all materials to C M P site, heating the bitumen and agregates to required temperature and mixing them in required temperature in central hot mix plant 20- 30 tonnes capacity conveying the mix by tipper trucks to paver site, spreading the mix in required temperature for uniform thickness of 40mm / 30mm with mechanical paver to the specified grades and cross sections and compaction by Vibratory roller to the required density etc., including labour charges for loading bitumen in to bitumen tank and metal to feeder unit,labour for attending to paver site etc., including hire charges and fuel charges for 20-30t C M P with bitumen boiler,tipper trucks, paver finisher, Vibratory rollers and all other tools and plants required,including all other incidental charges etc.,complete using C M P clause 507 of MORTH Rev-5 specifications.

Providing and fixing reflective road studs of 'Category A' Raised pavement markers made out of poly carbonate/methyl methecrylate/ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal rfelection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D 4280. The reflective raised pavement markers shall also confirm to the MORTH circular No RW/NH., 33023/10/97-DO.III dt.11.06.1997. The height, width and length shall not be less than 15mm, 90mm and 100 mm and with minimum reflective area of 13 Sq.cm on each side and the slope to the base shall be 35+/-5 degree. Each reflector shall have a CIL not less than values specified in Tablw 2 of said MORTH circular. The strength of detachment of the integrated cylindrical shanks. (of diameter not lesthan 19+/-2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635 Kg tested in accordance with ASTM D 4280 and confirming to IRC 35 - 2015 gudelines and MORT&H specification 804 etc., complete

Providing and Laying of hot applied Thermoplastic compound 2.5mm thick including reflectorising galss beads @ 250gms per sqm area, thickness of 2.5mm exclusive of surface applied galss beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes. Morth 803 Rev - V

Manufacturing, Supply and fixing of Retro Reflective Road name Sign Board Single Arrow of size 1.30x0.6 made out of Wide Angle cube comer micro prismatic grade sheeting conforming to IRC 67:2010 & Type XI standards of ASTMD D 495609 specifications and fixed over 2mm thick Aluminum sheet & back support frame of 25x25x3mm MS angle frame supported by 32MB stainless steel pipe all around and 65NM pipe vertical post firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 30cmx30cmx45cm etc complete., The information message shall be made out of cut out letters in Blue color transparent overlay film as per IRC 67-201 Guidelines. 7 years pre qualification warranty for Retro Reflective sheeting from the origional sheeting manufacturer & a certified copy of three years out door exposure report from an independent test lab for the product offered shall be submitted by the customer. IRC 67-2012