Municipal Administration And Water Supply Department Tender

Removal of Excavated Excess Earth away from the site to 5 KM including loading and transportation charges etc, complete as per standard specification

Centering for sides and soffits for plain surface such as slabs lintels sunshades staircase waist slabs etc., including strutting 3m high using M.S sheet of size 90cm X 90 cm and 10 Gauge fitted with M.S Angle of size 25x25x3mm laid over silver work (C.Wood) joists of size 10x6.50cm spaced at about 90 c/c and supported by casurina props . 10 to 13 cm dia spaced at about 75 c/c complying with standard specification.

Grade Beam

Reinforced Cement Concrete 1:1.5:3 (One Cement , One and half sand & Three coarse aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc.,complete.

Second Floor

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Second Floor

Supplying, fabricating, Erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Fabrication ,Supply and Fixing of Weld Mesh Screen using 'L' Angle alround of size 40x40xx5mm vertically and horizontally welded with 'L' Angle Frame and fully covered with Weld mesh of size 7.5x2.5mm including cost and conveyance of all material and lab

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 x 35 x 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 x 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 x 31 x 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 x 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers

Plastering with Cement mortar 1:5 mix, 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Paving the floor with kotta stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Painting two coats for Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of colour for open PVC light point / fan point (for electronic regulator) (5 points per coil) including cost of all material charges and labour charges etc, complete as per standard specification SD 18

Wiring with 2 x 1.5 sq.mm (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5A 3 pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point including cost of all material charges and labour charges etc, complete as per standard specification SD 36

Supply and fixing of single box type 4' x 40 W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting including cost of all material charges and labour charges etc, complete as per standard specification SD 89

Supply and fixing of 1200mm (48") AC Ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp including cost of all material charges and labour charges etc, complete as per standard specification SD 107

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains including cost of all material charges and labour charges etc, complete as per standard specification SD 65

Supply,Delivery and fixing of 20mm dia GI Service Pipe including cost of all material charges and labour charges etc., complete as per Specifications (L.R)

Supply and delivery of Gym materials for ISI standard mark best in quality including cost and conveyance of all materials and labour charges for stacking materials etc., complete as per standard specification

Hexagon Thumbles 3 kg

Hexagon Thumbles 4kg

Hexagon Thumbles 5kg

Hexagon Thumbles 6kg

Hexagon Thumbles 8kg

Weightlifting rod 5 ft

Weightlifting rod 6 ft

Weightlifting plate 3kg

Weightlifting plate 4kg

Weightlifting plate 5kg

Weightlifting plate 8kg

Thumbles Stand

Supply and delivery of imported LEG PRESS / HACK SQUAT with ISI standard mark in best quality including cost and conveyance of all materials and labour charges for stacking materials at gymnasium etc., complete (LR)

Supply and delivery of imported 6 way Multigym with ISI standard mark in best quality including cost and conveyance of all materials and labour charges for stacking materials at gymnasium etc., complete (LR)

Supply and delivery MULTI WEIGHT BENCH - INDIAN Structure : 100 mm x 50mm– 12 Gauge 50mm x 50mm – 12-Gauge Standard Hardware L.N.K Bolt Leather Seat 2” Thickness (OLYMPIC FLAT BENCH) (LR)

Supply and delivery ADJUSTABLE BENCH Structure : 100MM x 50MM – 12Gauge 50mm x 50mm – 12Gauge Standard Hardware L.N.K Bolt Leather Seat 2” Thickness (LR)

Supply and delivery PLATE STAND Heavy Duty including all labour and material charges etc., complete

GST 18%