Municipal Administration And Water Supply Department Tender

Dismantling the existing Plain cement concrete including removing the debris from the site and stacking useful material at work site for reuse etc., complete complying with standard specification.

Earthwork excavation for foundation in all soils and sub soils except in hard rock requiring blasting and depositing on bank with initial lead of 10m and initial lift of 2m inclusive of shoring, shuttering, bailing out water wherever necessary, refilling the foundation with excavated earth other than sandy soil in layers of not more than 150mm thick layers well rammed and depositing the surplus earth within the compound in place shown by the departmental officers and clearing and levelling the site etc,. complete.

Plain Cement concrete 1:4:8 [one cement, four sand and eight course aggregates] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification.

Random rubble masonry in CM 1:5 [one cement and five sand] for foundation and basement using best new rough and bond stones including simultaneous pointing above ground level with the same mortar etc., complete complying with standard specification.

Brick work In CM 1:5 mix using best Second Class Table Moulded Chamber Burnt Bricks 9"x4½"x3" having 350 kg/cm² compressive strength and 15% or less water absorbent in the period of 24hours immersement and confirming to ISI specifications including finishing, curing etc., complete complying with standard specification.

Supplying and filling Well gravel in layers of not more than 15cm thick well rammed, watered and compacted etc., complete complying with standard specification.

Plastering with cement mortar 1:5 mix, 12mm thick in all floors using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

Providing and laying of 80mm thick Interlocking Paver Block (TAMIN) in uniform shape of approved make to be laid in flurring bond pattern with 150mm thick quarry rubbish cushion below the uniform shape of approved non-skitting surface in the top and the rates including levelling the base, preparation of pavers as sub base, quarry rubbish cushion 150mm thick, laying out of pavement, cut the pieces to fix the edge, vibring the pavers, sweeping, transporting, loading and unloading etc., complete complying with standard specification.

Finishing the top of the roof slab with one course of Machine pressed tiles of size 20cm x 20cm x 2cm of approved quality laid in cement mortar 1:3 [one cement and three sand] 12mm thick mixed with waterproofing compound 2% by the weight of cement used and the top pointed with same mortar etc., complete complying with standard specification.

Paving the floor with 10mm thick Double Charged Vitrified Tiles in all floors over a base layer of cement mortar 1:3 [one cement and three sand] 20mm thick of walls and floors and pointed with the same colour cement neatly, including polishing with electric polishers to a high degree so as to make it perfectly smooth and showing etc., complete complying with standard specification.

Paving the floor with 8mm thick Joint free Rectified Glazed Ceramic Flooring Tiles of all colours in all floors over a base layer of cement mortar 1:3 [one cement and three sand] 20mm thick laid in-situ and pointed with the same coloured cement neatly, including polishing with electric polishers to a high degree so as to make it perfectly smooth and showing etc., complete complying with standard specification.

Dadooing the walls with 10mm thick Ceramic Tiles of size 300mm x 600mm of approved make and quality in cement mortar 1:2 mix [one cement and two sand] over 10mm base layer plastering and pointing with white cement neatly etc., complete as per standard specification.

Supplying and fixing in position of Aluminium anodised partition with 62x38x2mm extruded box section at bottom, vertical and horizontal members. The vertical members are spaced at 90cm c/c and to horizontal members are spaced at 1.20m, 2.10m and 2.40m height and the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick clear glass with necessary glassing clips, rubber beadings etc., including cost of labour for electrical consumption required for the fabrication, drilling holes in RCC columns with power drill to the required extent and make good to the original condition etc., complete and as directed by the departmental officers. The aluminium for frame to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns.

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish Single leaf door (with frame) half glazed and half PLB board using extruded aluminium section for frame and shutter with necessary accessories such as PLB 12mm thick, 5.50mm thick plain sheet glass, Alu. 'L' angles, Rubber beading, aluminium clips, best double action floor springs / door closer, handles, tower bolt, hinges, pivot and locks including labour and power consumption charges required for fabrication, if necessary chipping, dismantling, making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc., complete. The aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868 / 1962 of anodic film thickness of not less than 15 microns for all sections.

Supply and fixing FRP door shutter with frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of hold fasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., complete complying with standard specification.

Supply and fixing of M.S Grills with Doors, Windows, Ventilators and Gates of required size suitable to site condition with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc., complete as per standard specification.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc., conforming to IS specification including primer coating and enamel painting as per design given by the departmental officers etc., complete as per standard specification.

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 gauge having width 1050mm. The sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws and plastic washer. The washer and screws to be fixed by using minute power machine drilled without damaging the sheets paint coating to be regular modified polyester coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like Malabar Mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 75mm thickness in RCC 1:2:4 (one cement, two sand and four course aggregates) using 20mm size Hard Broken/Machine crushed Granite Stone Jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification.

Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster of paris, putty wherever required etc., complete as per standard specifications.

Painting two coats for New iron work surface using best quality synthetic enamel paint etc., complete complying with standard specification.

Painting two coats for old iron work surface using best quality synthetic enamel paint etc., complete complying with standard specification.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylem sheet of 3mm thick with painting of suitable colour for open PVC light point / fan point. (for electronic regulator)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18").

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box in flush with wall with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point.

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 63mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point.

Supply and fixing of 4' 18W Crystal Glass LED Tube Light Fitting with necessacry clamps etc., complete. (Havells / Equivalent)

Supply and fixing of LED Outdoor 48W LED Street Light Fitting including wall bracket with necessary fastners and fitting charges etc., complete.

Construction of Inspection Chamber of 0.60m X 0.60m X 0.60m clear size including earth work excavation, base concrete of 50mm thick CC 1:5:10, 11.50cm thick brick work in cement mortor 1:5 using best quality second class ground moulded bricks of size 9" x 4½" x 3", Inner, top and outer sides should be plastered with CM 1:3, 12mm thick and 50mm thick wearing coat 1:3:6 using 20mm metal should be laid over the inner flooring and the top covered with 50mm thick precast slab etc., complete complying with standard specification.

Supplying and fixing in position of Indian make Colour glazed earthenware WASH HAND BASIN of size 550x400mm with a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waste water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specification.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.