Municipal Administration And Water Supply Department Tender

For with strutting

Reinforced Cement Concrete 1:1.5:3 mix using 20mm ISS gauge HBBG metal from the approved quarry including mixing, laying, consolidating, curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Above 4.50m ht 1st Floor

Brick work in cement mortar 1:5 (one cement and five parts of crushed stone m.sand) using II class ground moulded bricks of size 9 " x 43/8 "x2 3/4 " including finishing curing etc., complete complying with standard specification

For First floor

Plastering with Cement Mortar (1:5) mix (one cement and five P.sand) 12mm thick in all floors including cost and conveyance of all materials to site and labour charges etc., complete as per standard specification

Flooring with Stain free Nano polish Vetrified flooring tiles of size 600 x 600 x 8mm of approved colour and quality of required size laid in cement mortar 1:3 mix 20mm thick and pointing with the same mortar complete and finish very neatly etc complete.

Aluminium Two Track window size 1.20 x 1.30m Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in two track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an average anodic film thick of not less than 15 microns. ( All materials should be got approved by the Exe.Engr before fixing in position)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch boc 5A F.T. switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable color for concealed PVC light / fan point (for electronic regulator) SD-24.

Wiring with 2X 1.5 sqmm (22/0.3) PVC insulated Sc unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150x100x113mm TW switch box and 5A 3 pin non inter locking CS plug with painting of suitable color with continuous earth wire connection of 14SWG TC wire for Open PVC plug point ( SD-38)

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15 A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire , and making good of the concealed portion, with suitable colour for Open power plug point (SD.No.40)

Supply and fixing of 40W 4 Feet LED Fitting with LED with TW round blocks on wall or ceilig with flu tube with PVC unsheather copper leads from terminals

Supply and of 1400mm sweep ( 56") AC ceiling fan complete with stepped electronic 300 W regulator with 1 metre down rod on the existing clamp.

Fabricating,supplying and fixing and inposition of MS roof truss work using necessary Pipes,Hollow section,L angle and Flats of required size including cost of all materials,fabrication,labour charges with one coat of red oxide priming etc.,complete

Supplying and fixing inposition of pvc painted Galvanium sheet corrugated roofing with 0.47mm FRB thick with painted coat lncluding cost of bolt,nut and washer etc.complete.

Providing and laying of 63mm thick high strength type of interlocking pavement block in required sizes of minimum compressive strength of 400 kg/cm2 in unipaver shape of approved make to be laid in lorrying bone pattern with approved nonsticking surface in the top the rate is including levelling the base, preparation of sub base with sand cushion 100mm thick, laying out the pavement, cut the pieces to fit the edge, vibrating the pavers, sweeping the sand grouting, providing transporting, loading, unloading and laying of paver block and Priming coat of red oxide painting as per standard specification

Painting with Enamel paint over the new iron works of approved quality and colour with priming coat including the cost all materials etc complete.

Painting two coats with ready mixed plastic emulsion paint approved quality and color over a priming coat including through scraping clean removal of dirt etc., complete and including of necessary plaster of paris putty wherever required etc., complete as per standard specifications.