Municipal Administration And Water Supply Department Tender

Supply and fixing Perculated gypsum board false ceiling using 18 mm thick of approved Quality and design suspended from the ceiling using ‘U’ shaped Galvanised Iron channel of size 25 x 25 x 0.55 mm thick at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing ‘U’ shaped G.I. Channel of size 50 x 30 x 0.55 mm thick at 0.60 m centre to centre on cross direction and fixing of ‘U’ shaped G.I. channel of size 50 x 10 x 0.55 mm thick at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W. reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design/pattern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using kit ply 12 mm thick and opening should be covered with Acrylic panel etc. complete complying with standard specification and as directed by the dept officers. All the materials should be got approved before use work.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter and should have provision to fix AL drops, tower bolt hinges and lock plates inclusive of cost of all materials etc. complete complying with thew standard specifications.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light/fan point (for electronic regulator) (5 points per coil)(SD 22)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm(18")(SD 106)

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3 pin non inter locking wall socket with 5A Flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC Plug point. (SD36)

Supplying and fixing of Exhaust fan fitting

Supplying and fixing of 1.5 Ton AC fittings

Provision for Curtain

Floor mat

Provision for Curtain

Floor mat

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.

Supply and fixing of single box type 4'36 W flu fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting(SD 87)

Supply and fixing of WALL MOUNTING FAN

Spot lights

3 watts Spot lights