Municipal Administration And Water Supply Department Tender

Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).(QUOTATION)

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.(QUOTATION)