Municipal Administration And Water Supply Department Tender

4. Reinforced Cement concrete 1:1.5 :3 (one cement, one and half M Sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rec works wherever necessary as directed by departmental officer etc., complete.

Supplying and fabricating and placing in postion MS or RTS Bar reinforcement to all RCC Works as per the design given including cost of steel and bending wire also all floors.

Flooring with Ellis pattern using 6mm chips (No sand to be used including all cost etc complete

Fly ash Brick work in CM 1:5 (one cement & five sand) using size 9"X4 3/8"X 2 3/4" including finishing, curing, etc., complete complying with standard Specification

Plastering in CM 1:5 to 12mm thick including all cost etc complete

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.1.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated.cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supply and fixing of mild steel door using all round "L" angle 25 X 25 X 6mm thick, cross bracing 20 X 6mm M.S.Flat with necessary locking arrangements including cost and conveyance etc., Size : 0.60 X 1.85 = 1.11 m2

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal

12. Painting with enamel paint two coats over one coat of primer coat for iron doors layer by layer with equal intervals using good quality approved colour paint including all cost etc complete.

Conveyance of excavated earth and dismantled depreeze from site to 15 km including all cost etc complete

Supply and run of 2 of 4 sq mm(56/.3) PVC insulated SC unsheathed Cu.Conductor of 1100 v Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

15. Wiring with 2x1.5sq.mm (22/3.0) PVC insulated unsheathed single core unsheathed copper Conductorcable of 1100V grade in suitableheavy gauge MS conduit pipeon wall and celling with M.S accessories inflush with wall with 150mm x 100mm x 75mm MS swithbox with 3mm thick hylum sheet cover for 5A 3pin non interlocking CS plug with continuos earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point.

16. Wiring with 2x1.5sq.mm (22/3.0) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessorie in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A switch with continous earth wire connection of SWGTC wire for making good of the concealed portion with suitable colour for PVC open light/Fan Point (For electronic regulator) (5 Points per coil)

Supply and fixing of Double pole 32 Amps MCP 240V/415 V 50 HZ-AC supply on suitable TW board including all cost etc complete.

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condenser with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting etc, complete as  per standard specifications SD-83

19. Painting with first quality emulsion paint two coats over a priming coat including through cleaning, scrapping, removal of dust and including necessary plaster of paris putty works wherever required etc., completed.

upply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading,unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including  cutting threading and fixing charges etc.,