Municipal Administration And Water Supply Department Tender

Curved Surfaces 17.30m to 18.30

Curved Surfaces 18.30m to 19.30

Curved Surfaces 19.30m to 20.30

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - For Circular surfaces such as Circular RCC columns etc. Circular Column 13.30m to 14.30m

Circular Column 14.30m to 15.30m

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. For 14.64m to 18.30m from G.L

For 18.30m to 21.96m from G.L

Supply and fabrication of steel required for all RCC items of works involved in the schedule, cost of steel at site fabrication, labour charges for cleaning the rods straightening, cutting, bending, tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as as per design given and specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc complete as per standard specification

Colour washing two coats in all floors using best Cement Paint and best quality of approved variety and burshes, scaffolding charges etc. complete complying with standard specification.

Supplying and fixing in position C.I.Manhole covers (light or heavy duty) of 600mm X 600mm sizes of best approved quality and as per standard specifications etc.,complete. PWD SOR SL.NO.234, P.NO.55

Providing and fixing of RCC inner access ladder in RCC 1:1.5:3 (One cement, one and half sand, three aggregates) using 20mm HBG stones for OHT including grill in position, centering, shuttering charges, mixing concrete curing etc, to required height and clear width of 45cm consisting of two nos of vertical post of 10cm X 15cm and step salb of 25mm X 25mm etc,complete and as directed by Municipal Officers.

Fabrication, supply, delivery and fixing of outside MS Ladder of 45cm clear wide made out of 50 mm x 50mm x 6mm MS angle for both sides and for steps at 30cm C/C welded jointed etc ., for I staging from GL to 1st level brace (weight 4.5kg/m) IInd and IIIrd staging upto floor slab and IVth staging from floor slab to roof top. Supply, delivery and fixing of 32 mm GI pipes medium for hand rails from I stage to IVth stage. RCC M30 Grade mix for Landing slab 5 nos. at Ground Level- 1No. and above Ground Level - 4Nos. Supply and fixing of 32mmGI pipe medium for hand rails for the Landing slab. Supplying and fixing of MS Base plate of 100mm X 100mm X 6mm thick for fixing Anchore fastener bolt forfixing of hand rails at Landing slab and MS Ladder providing locking arrangements with two coats of approved enamel paint over one coat of red oxide paint as per approved Type Design and as directed by TWAD board officers. For OHT Capacitie 1.00 lakh 12m stage

Providing and fixing of RCC 1:2:4 (one cement, two sand and four course aggregate of 20mm size hard blue granite broken stone) for ventilators of approved pattern including cost of cement, reinforcement, centering, shuttering, strutting etc., complete as generally shown in plan and as directed.

Providing Cut stone set in CM 1:3 (one cement and three sand) using well dressed cut stone supporting inlet pipe of size 0.30 x 0.30 x 0.15m for service reservoir etc., complete as per standard specifications and as directed by Engineer-in-charge

Providing and fixing in position of PVC water bar 150mm wide with single bulb for horizontal joints necessary holders fabrication, the rate inclusive of cost of water bar, holders fabrication and fixing in position etc complete as per standard specification and as directed by the Engineer.PWD SOR SL.NO.65, P.NO.38

Supply and delivery of CI D/F sluice valves with cap along with specials of the 150mm dia in size confirming to IS 14846 / 2000 (PN1) including flanged tail piece and other specials as required, loading, unloading, transportation charges and stacking and jointing including cost of jointing materials etc, complete as per standard Specification.TWAD SOR SL.NO.234, P.NO.55

Provision for pipe connection arrangements for inlet, outlet, scour and overflow etc, including cost of pipes, specials, valve, labour charges for lifting, aligning, fixing of DI pipes etc, complete as detailed below

Supply and delivery of CI D/F sluice valves for Scour with cap along with specials of the 100mm dia in size confirming to IS 14846 / 2000 (PN1) including flanged tail piece and other specials as required, loading, unloading, transportation charges and stacking and jointing including cost of jointing materials etc. complete.

Goods and Service Tax @ 18%