Municipal Administration And Water Supply Department Tender

R.C.C. 1:1.5:3 Mix (One cement one point sand Three hard broken granite stones) for all the reinforced cement concrete works using 20mm gauge hard blue granite stone jelly including cost and conveyance of all materials to site including all labour charges for concrete mixing, laying, watering curing properly excluding cost of steel and centering etc., complete complying with standard specification.

Supply fabrication and placing imposition of mild steel for steel rod of various sizes as directed including all labour charges for cutting and binding and tying with cost of binding wire, etc., complete as per standard specification.

Brickworkin CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 9" X 43/8" X 2 3/4" including finishing, curing, etc.,complete complying with standard specification

Fillling with well gravel layers of not more than 30cm thick,well rammed, watered and compacted, complying with standard specification etc., complete.

Ceiling Plastering with C.M. 1:3 Mix (one cement and three sand) 10mm thick finishing including cost and conveyance of all materials to site and all labour charges, watering curing and all other incidental charges etc., complete complying with standard specification.

Plastering with C.M. 1:5 Mix (one cement and five sand) 12mm thick finishing including cost and conveyance of all materials to site and all labour charges, watering curing and all other incidental charges etc., complete complying with standard specification.

Paving the floor with Vitrified Floor Tiles of size 60 X 60cm of approved brand and colour Marbonite tiles in all floors base layer of cement mortar 1:3 (one cement and three sand) 20mm thick using first quality Marbonite tiles of size 60 X 60cm and point with colour cement neatly and fixed in position so as to make perfectly smooth and to alignment etc., complete complying with standard specification

Flooring finishing with first quality design ceramaic tiles of all colours of size 305cm X 305cm X 6mm laid in cement mortar 1:3 mix to 20mm thick and painting with white cement using 0.30 kg/1m2 including finishing the jointing and painting flush with tiles surface etc., complete - 10 m2

Flooring (No sand to be used) using with 6mm chips C.M.1:2 mix using 20mm thick including cost of materials to work site and all other labour charges

Terrace flooring with pressed tiles using CM 1:3 (One Cement, three sand) mix including the cost for Pointing as per the Direction of the departmental officers etc. complete

Solid PVC door shutter using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fix in position including necessary furniture and fittings. The cover all size of top rail, Lock rail and bottom rail shall be 70mm x 45mm, with suitable rebate for housing the shutter

Daddoing the walls with first quality approved colour Glazed tiles of size 150X150X6 mm laid in cement mortar 1:2 mix to 10mm thick and painting with white cement using 0.40 kg/1m2 including finishing the jointing and painting flush with tiles surface etc., complete

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

European Water Closet (Colour) with 'P' or 'S' Trap with Double Flapped seat and seat cover with Brass Highes and 10 litre capacity PVC low level flusing tank with all internal fittings with necessary connection as per standard specification

Supply and fixing of mild steel door,Truss and Purlins including cost of cutting, welding and conveyance etc.

Painting with enamal paint two coats for new Iron work including one coat of priming coat and using the best quality Iron primer and best quality synthetic enamel paint etc complete complying with standard specification

Painting with plastic emulsion paint two coats over base coat for new plastered surface for using best quality and aproved colour of oil bound distemper conforming to ISI specification etc., complete complying as directed by the departmental officers as per standard specification.

Wiring with 2 x 1.5 sqmm (22 / 0.3) PVC insulated SC sheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe cealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For electronic regulator).

wiring with 2x1.5sq mm (22/.3) PVC insulated SC unsheathed copper conductore cable of 1100V Grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories in flush with wall with 150mmx100mmx75mm MS switch box with 3mm thick hylem sheet cover for 5A 3pin interlocking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed Plug point. (SD 12)

Supply and run of 2 of 4 sq.m (56/0.3)PVC insulated SC unsheathed CU.Conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(SD 44)

Supply and fixing of WT bulk head fitting with guard (Phillips/Bajaj/Crompton/K.Lite) Suitable for incandescent lamp with 11 Watts CFL Bulb Bulb(SD 83)

Supply and fixing of single box type 4"40W flu fitting completed with copper choke and condensor,with condult pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting with Tube (SD 87)

Supplying and fixing of 1200mm(48")sweep AC ceiling fan complete with stepped electronic 300W Regulator with 1 metre down rod with fan clamp with side plates and crpss arm of size 450mm(16") (SD 106)

Supplying and fixing of HDPE Water Tanks with suitable specials including cost of materials to site and all other labour charges.etc

Supplying and Laying Hydraulic Pressed Paver Block Providing and laying of 63 mm thick high strength of Hydraulic Pressed Paver Block in size of minimum compressive strength of 40 N/mm2 In uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including leveling the base perpareation of pavers as sub base, stone dust cushion 150 mm thick laying out of pavement cut the pieces to fix the edge vibring the paversl sweeping transporting loading unloading of laying paver block as per the standard specifications

Supplying and fixing with Galvalume Colour Sheet of size 0.47mm thick including necessary bolt, nuts and bitumen washed etc., completed - 10 m2

Supply and Fixing in position of Indian make White glazed earthware WASH BASIN 550mmx400mm with all accessories such as costIron brackets , 32mm dia C.P waste coupling 15mm dia G.M wheel valve ,15mm dia Nylon connection , 15mm dia Brass Nipples, 15mm C.P Pillar tap etc., complete.

Supply and Fixing of 48W LED Street light Fitting with necessary Bowl and Bracket and Bulp as per Standard Quality as per the Direction of the Departmental officers etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supply and Fixing of 1HP Motor with pumpset as per Standard Quality as per the Direction of the Departmental officers etc., complete.

Conveyance of Surplus earth from work site to City outer with average lead of 15 km