Municipal Administration And Water Supply Department Tender

Rein forced Cement Concrete 1:1.50;3 (One Cement, one and half sand and three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Brick work in CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT In Cement Mortar 1:5 (one cement and five sand)

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Fabricating, Supplying and erection of iron vertical post made with 150 x 150 size square tube of 3.00m height and one number of 150 x 150 x 16mm size m.s plate is used on base plate and same is welded at bottom of the vertical post and one number of 150 x 150 x 16 mm size m.s plate is used as gueset plate is welded at top of the same post and necessary holes are provided at the base plate and gueset plate at an appropiriate places. the iron post is erected vertically in correct alignment position used with hydralic power crane and the post embeded on the R.C.C. Concrete bed and tightend with base plate in anchor rod using with heavy type nut. the rate including cost of materials, laboure charges such as cutting, welding, drilling, Power consumbtion charges etc complete., and the iron members are painted with one coat of anti corrosive at sincromat primer and with two coat of best enamal paint, and loading and unloading charges conveyance and any other I.C etc. complete., as directed by the departmental officers.

Fabricating, supplying and erecting special type iron Truss made up of 50 x 50 x 6 mm M.S Double Angle one at roof top 2.50 m length another at bottom 3.00 m length The height of the ridges at one side is 0.90m and another one is in front side is 0.90m .The intermediate and slope angle isto be same as 50x50x6mm angle necessary clit plate are provided on trus top at an appropiriated places . necessary holes are provided in the angle for connecting the vertical post. the special type truss may be erected on face of the vertical post in correct alignment of position used with hydralic power crane of including cost of heavy type bolt, nut washers etc complete And including cutting, drilling, Grinding, power consumption charges etc., complete the iron membrs are painted with one coat of anticorrosive sincromate primer and two coat of best enamel paint, loading and unloading transportation charges and any other incidental charges etc., complete.

Supplying and fixing in position of Special type Zinc sheet of 0.50mm thick of approved quality and best varitey with necessary ridge sheet and rate including cost of necessary bolt,nut,washers etc., complete and ercting the Galvanished Sheet in correct alignment in position used with hydraulic power crane or necessary scoffolding etc., and the rate is including cost of Loading, unloading,Transportation charge and any other I.C etc., complete as directed by the departmental officers.

Supplying,fabricating and fixing of Iron purline made with 75 x 40 mm M.S Tube and necessary holes,clit plates are provided on the M.S Tube at an appropriate places as directed . And including cost of bolt,nut,washrs etc,. Complete The iron members are painted with one coat of red oxide primer and two coat of enamel paint. The rate is including cost of welding, drilling and fixing the purline with correct alignment in position and including cost of Loading, unloading,Transportation charge and any other I.C etc., complete as directed by the departmental officers.

Fabrication supplying and fixing of steel sitting bench of size 1.80M L x 0.45 wide with 50x 20ms tube is top of the bench six row and 8 Nos of legs are povided with 40x40 MS tube and necessary back rest are provided with MS tube 50x20mm size. The rate is including cost of welding , grinding and painting one coat of primer and two coat of best enamel paint etc complete.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position of Name board by using the M.S square pipe of size 35x35mm alround the name board and intermediate vertical pipe is same as above. 1mm Aluminium Sheet is fixing on the top of M.S pipe and the name board and imported reflected sticker lettering is fixing on the name board etc., complete. The rate shall be inclusive of cost material,loading & un loading, Transportation charge and any other I.C etc., complete as directed by the departmental officers etc., complete complying with standard specification.

Supplying and fixing in position of Name board by using the M.S square pipe of size 25x25mm alround the name board and intermediate vertical pipe is same as above. 1mm Aluminium Sheet is fixing on the top of M.S pipe and the name board and printed flex cloth is fixing on the name board etc., complete. The rate shall be inclusive of cost material,loading & un loading, Transportation charge and any other I.C etc., complete as directed by the departmental officers etc., complete complying with standard specification.

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. Dadooing with printed design colour glazed tiles of size 300mm x 200mm x 6mm

Supplying and fixing in position of Stainless steel hand rail made out of SS 304 Grade using 40mm dia stainless steel tube of 1.69 mm thick to a height of 90 CM from finished level and welded to 25mm dia stainless tube of 1.69 mm thick as vertical post at 90 cm c/c and 3 nos of 15mm dia horizontal stainless tube 1.69 mm thick etc., complete as directed by the departmental officers.