Municipal Administration And Water Supply Department Tender

Supplying and filling in foundation and basement with filling crushed stone Dust in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators etc completed

Foundation & Basement

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed

Column

Plinth Beam

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick Work in CM 1:5 mix using Second Class Ground Moulded Chamber Burnt Bricks 9 " x 4 3/8 " x 2 ¾ " size including cost and conveyance of materials and labour charges etc., complete as per standard specification. (Item No. 2b )

Foundation & Basement

Superstructure from G.F

Plastering with CM 1:5 mix using 12mm thick including cost and conveyance of materials and labour charges etc., complete as per Standard Specification

Painting two coats of newly plastered wall surface with approved cement paint over cement plastered wall surface, ceiling and including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required and cost of painting materials, brushes, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer

Supply delivery and filling of carted earth in layer of not more than 15cm thick including watering with all layers and consolidation complying with standard specifications inlcuding cost and conveyance of all materials and labour charges etc., complete

Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Plain Cement Concrete 1:2:4 mix (One Cement, Two Fine Aggregate and Four Course Aggregate) Using 20mm ISS HBG metal including all cost conveyance of materials and labour charges including vibrating charges etc. complete as per standard specification.

Fabrication supply and fixing in position weld mesh inclusive and cost of red oxide prime etc.., Complete as per standard specification.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanium iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Special Ceiling Plastering for RCC slabs and beams with cement mortar 1:3 mix 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with MS switch Box and 5A FT switch with painting of suitable colour continuous earth wire connection of 14 SWG TC wire for light point / fan point (for electronic regulator)(SD-23)

Wiring with 2 x 4 sq.mm. (56 / 0.3mm) PVC insulated single core unsheathed copper cable conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mm x 100mm x 75mm MS switch box for 15A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection by 14 SWG TC wire for open power plug point (SD-38)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 14 SWG TC wire with painting of suitable colour (SD-54)

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube (SD -88)

Supply and fixing of 25mm G.I. service pipe with bend including cost and conveyance etc., complete., as per standard specification as directed by the departmental officers

Painting with two coats of Approved Colour painting including cost and conveyance of materials and labour charges etc. complete as per Standard specification for (New Iron Surface)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD - 106)

Hydraulic Plastic Bailing machine with mechanical vertical clamping force - MS body - Chamber size 700 X 500 X 1400 (mm) - Bail Size 700 X 500 X 650 (mm) with bail weight of 50-60Kg, 15-20 Cycle time per bale in minutes, Single Cylinder 700 X 500 (mm) - hydraulic system gear cum plunger pump system and day light gap between bottom plate and pressing plate 1400 mm Motor power 7.5 HP, 2Nos ties of rope, single door, body plate 8 mmm thickness, clamping plate thickness 30 mm and 3 Phase - electrical control system - manual bale eject swing plate with screw system, Hand lever operated and drainage system for the residual and fluid/ liquid while rushing/pressing the material provisions, Overall weight of the machine in 1000 KG Overall dimensions of the machine in mm x mm x mm (length x width x height) 700X500X650 mm Additional Parameters: The Machine should be painted and power coated to avoid rust, Packaging should be into crate using timber bracing, Electrical safety system shall confirm to IS 302, Instruction Mannual,Service details, Maintanance manual l to be provided with the Machine,Installation and demonstration to be completed by the seller before acceptance of item, Certificates: Manufacturer of the machine shal be holding ISO 9001:2008/2015 certification, Details of ISO Certification PICL/QMS/0518/2059 31.05.2018, Test certificate from Govt/NABL/ILAC approved Lab regarding various performance parameters indicated as well as Electrical Saftey Systems as per IS 302, Test Report No GM/2019/78 Test Report Date 25/11/2019, Name and Address of Lab GUJARAT METAL & EQUIPMENT TESTING LAB- RAJKOT Copies of all certifications and test reports to be provided to buyer on demand at time of supplies . Including labour cost. (WARRANTY 1 YEAR)

Supply, fixing and commissioning of Plastic shredder machine( grinding of all 7 category of plastic waste ) wit 6 blades size of 46 x 13cm , with shredding capacity of 200 to 250 kg per hour having motor capaity of 15 to 22.5 Kw with cast iron body including conveance and all labour harges etc,complete with standard specification.

Supply and Delivery of Sorting Table size 8.00 x 1.50m including conveance and all labour harges etc,complete with standard specification.

Supply and Delivery of Electronic weighing scale 2000KG capacity including conveance and all labour harges etc,complete with standard specification.

Supply and Delivery of manual Fork lift of capacity 100kg capacity including all labour harges etc,complete with standard specification.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Supplying and erecting pull and push type rolling shutter with I.S.I. make of approved size and section using 18 gauge G.I.sheet with manually operated type. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc, complete as per standard specification.

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc.,complete. (TWAD SOR PG.NO87)

Fully Panelled Single Leaf door 0.90 x 2.00Mt

Fully Panelled Double Leaf Window 1.20 x 0.90Mt

Ventilator 0.45 x 0.60

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm dia PVC 6KSC Pipe

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of 20mm dia in size including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type) with I.S.I.mark of 25mm dia in size including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

Suppling and fixing in position 15mm.diameter brass screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac , thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supply and fixing of following Plumbing G.I.materials

20mm dia G.I coupling

20mm dia G.I Tee

20mm dia G.I Elbow

20mm dia G.I union

20mm X 15mm dia G.I Reducer Elbow

Supplying and fixing in position C.I.Manhole covers (light or heavy duty) of 600 X 600mm in size of best approved quality and as per standard specifications etc.,complete.

Supplying and fixing P.V.C. ventilating shaft of 110mm dia and 3m height of best approved quality and as per standard specifications.

GST. 18% (CGST-9%, SGST-9%)