Municipal Administration And Water Supply Department Tender

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Supplying and fixing of 40mm cuddappa slab including all cost and conveyance of materials complete etc.,

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (5 points per coil)

Wiring with 2 x 1.5 sq.mm (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5A 3 pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point

Supply and fixing of following electrical item including cost of materials and labour charges for fixing etc complete.,

9W LED bulb

20W LED tube light

1200mm AC Ceiling fan

25W street light fitting

63A 4 pole Isolator

3 phase starter

Single phase starter

63A fuse carrier

RCCB

3 phase EB meter box

7/20 CTS wire

25mm GI pipe (service connection 3m)

Supply and fixing of following pipes and specials including cost conveyance to site, labour for cutting, threading etc., complete with standard specification.

15mm CP long body tap

15mm CP short body tap

15mm Health facite

5" gratings

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Manufacture and supply of shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 120 X 65 X 50, channel 75 x 40, L angle 40x60 & shaft 60mm dia. Capacity of 1 Mt to 1.5Mt/ Hour with single shaft cutter, stell grade, 10 Hp motor, size 600mmx800mmx600mm, chute - yes (feeding & discharge) with mannual feeding, Electrical - 10 Hp starter only without cable, total machine height is 2000mm and width 12mmmm feeding conveyor - 1 No (Mannual) etc, complete

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breadth of 0.50m wide for organic waste shorting and conveyor structure should made with MS heavy tubes, MS channels with gear motor of 2 HP /50 RPM/ 440V/ chain drive motor rollers with heavy rollers - 2 Nos, continuous rollers - 2 nos and shaft should be ISI standard bearings, MOC EN 8 make should be of HAVELLS / MARATHAN and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP hopper with necessary safety guard facilities and all materials should be got approed by the Engineers in charge before fixing in position including cost of all materials and labour charges etc, complete