Municipal Administration And Water Supply Department Tender

Supply and filling the Gravel each layer of not more than 15cm thick for sides of the revetments and the cost shall including materials and labour charges water and compacting etc complete as per standard Specifications

Manufacturing, supplying and fixing Precast Plain Cement Concrete slabs of following thickness in PCC 1:2:4 (one cement, two sand and four aggregates), using 20mm HBGS jelly including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Pointing the Dry Stone Packing with Cement Mortar1:3 mix (one cement and three sand) to flush pointing , curing and including cost and conveyance of all materials to site etc complete

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Cement concrte 1:2:4 mix ( one cement, two sand and four aggregate ) including the cost and conveyance of all materials and excluding the cost of steel and including the labour charges for mixing, laying of concrete and curing etc complete as per the standard specifications.

Plastering with cement mortar (1:4) (one cement & four sand) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications.

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Providing and laying ,spreading and compacting graded stone aggregate to wet mix macadam (WMM ) soecification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

supplying and fixing of RCC fencing post size of 2.10m X 0.10m X 0.10m with Main vertical bars: 4 Nos. of 8 mm dia round MS bars.Stirrups: 6mm dia round M S bars not more than 25cm centre to centre (13 Nos.) including conveyance of all materials to site etc.,post @ 3m C/C 267/3=92

Chain link - 2" x 2" using 10 Gauge stainless Steel Wire (of all sizes) The rate is inclusive of the labour charges for cutting and Binding with Binding Wire ect.complet.,

GI STEEL TUBULAR POLE FOR STREET LIGHT 4 Metre Length Double Bracket Pole with Base Plate (250 x 250 x 6mm)76.10mm OD x 3.65mm Thick x 4000mm Length as per TWAD sor page 201.

Supply and fixing of 30W LED White Street Light Fittings with casting Water proof doom and low voltage power savings with long time high solution luminance, IP66 Led Safe® optical compartment, a separate IP66 control gear compartment, an extruded aluminium painted housing, a toughened glass protector,permaently sealed with a robotically dispensed silicone sealant, closed at one end by an end cover and the other end by a frame and door assembly (to access control gear) both made of injection moulded polycarbonate, a removable control gear plate, safety plug and socket system, high pressure die cast aluminium painted mounting spigot suitable for horizontal mounting (Ø32-42mm) with tilt flexibility of ± 10 degrees, with lensoFlex2® technology,PMMA lenses with wide photometry for increased pole spacing,50,000 hours =L70,Ta = 55º,surge protection of 10Kv ( in differential and common mode),Power factor ≥0.90,colour rendering index≥65 and neutral white light (4,100ºK.) with necessary clamps, brackets and accessories etc complete

GST. 12% (CGST-6%, SGST-6%)