Municipal Administration And Water Supply Department Tender

Wiringwith2x4sq.mm.PVCinsulatedSCunsheathedFRLScoppercableconductorcableof1100VgradeinsuitableheavygaugeMSconduitpipeonwallandceilingwithMSaccessorieswith150mmx100mmx75mmMSswitchboxfor15A3pinnoninterlockingCSplugwithpaintingofsuitablecolourwithcontinuousearthwireconnectionby4sq.mmcopper wire for open power plug point SD 13

Supplyandfixingof1200mm(48")sweepACceilingfancompletewithsteppedelectronic300Wregulatorwith1metre down rod with fan clamp with side plates and cross arm of size 450mm (18") SD 106

Supplyandfixingofsingleboxtype4'36WfluorescentfittingcompletewithelectronicballastwithTWroundblocksonwall or ceiling with flu tube with PVC unsheathed FRLS Copper leads from terminals to the fitting SD 87

SupplyandfixingofTNEBmeterboardsuitablefor32Asinglephaseserviceconnectionwith32Afuseunit(500V)32Aneutrallinkandearthlink(1"x1/8"copperflat)onTWplankofsize375mmx300mmx19mmwithsupportingTWreepersof1"thickaneithersidewithpaintingwithsuitableboltandnutsforfixingtheTWplankonwallwithearthconnectionandinterconnectionwith7/20PVCinsulatedcopperwirefromEBmetertofuseunitwith1No40Amp30MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection SD 125

Supplyandrunof2of1.5sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100Vgradeon7/20GIbearer wire for service connection mains SD 64

Supplyandrunof4x6sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100Vgradein32mmdiaGIpipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains SD 73

Supply and delivery of water supply PVC and GI special including cast and conveyance and all charges etc., Complete.

Bore 200 mm Adoptor set

1 1/4" GI Bend (32mm)

200 mm Bore cover

32mm GI coupling

32mm x 25mm GI Reducer

32 mm UPVC pipe bore pipe 10Kg/m2

PVC rope 50m length

2.5 Sq.mm cable submerisible PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 AND AS AMENDED THEREAFTER

32 mm PVC pipe

32 mm PVC Elbow

32mm PVC Tee

50 mm PVC pipe

50 mm Elbow

50 mm Cupling

Ball valve (32mm) (Polypropylene with teflan seating)

500 liter HDPE Tank

G.I. Hex Nipple

PVC tap 20 mm

110 mm PVC pipe 6 kcs

110 mm PVC Elbow

110 mm PVC Tee

Supply and delivery of clear water vertical wet type submersible pump conforming to IS 8034/2002 and as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor suitable for operation in AC single phase 230 V+/- 10 %,50 HZ +/-5 %. 15x40

Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation. 50x25

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by ‘V’ notch method.

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days. Upto 5HP

Supply and fixing of 900 mm RCC ring for sweage including cost and conveyance and all labour charges for loading unloading etc., complete.