Municipal Administration And Water Supply Department Tender

Supplying and erecting centering including necessary supports for the plane surfaces such as RCC Column Footing, Plinth Beam, & Sill Beam etc., using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding supported by casurina props of 10cm to 13cm dia spaced at suitable intervals etc., complete complying with standard specification.

Supplying and erecting centering for soffits of Square / Rectangular Columns including strutting 3m high using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with M.S angles of size 25mm x 25mm x 3mm laid over silver Oak (C.W) joists of size 10cm x 6.5cm (spaced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced of 75cm c/c) etc., complete complying with standard specification.

0.00m - 3.00m height

3.00m - 4.00m height

4.00m - 5.00m height

5.00m - 6.00m height

6.00m - 7.00m height

7.00m - 8.00m height

8.00m - 9.00m height

Supplying and erecting centering for soffits of plane surfaces like RCC Slabs, Lintels, Sunshades, Square Columns, Staircase waists, Beams etc., including strutting 3m high using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with M.S angles of size 25mm x 25mm x 3mm laid over silver Oak (C.W) joists of size 10cm x 6.5cm (spaced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced of 75cm c/c) etc., complete complying with standard specification.

0.00m - 3.30m height

3.30m - 4.30m height

Providing and laying in position standardised concrete mix M-20 Grade in accordance with IS 456-2000 using 20mm and down graded hard broken jelly for all RCC items of works with minimum cement content of 3250kg/10cum and maximum water cement ratio of 0.50 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without impairing strength and durability with about (5.0cum) 7730kg of 20mm machine crushed stone jelly and with about (3.30cm) 5156kg of 10-12mm machine crushed stone jelly and with about (4.79cum) 7760kg of M-Sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing etc and providing fixtures like fan clamps in the RCC floor / Roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and directed by the departmental officers. The Coarse and fine aggregates to be used should comply with the requirements of IS standards.

upto 1.50m Depth

upto 4.50m Height in Ground Level

4.50m to 9.00m Height above Ground Level

Supplying, fabricating and placing in position of Steel Reinforcement using Mild Steel or Ribbed Tor steel bars for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete complying with standard specification.

Fly Ash Brick work In CM 1:5 mix using best Fly Ash Bricks of size 230 x 110 x 70mm including finishing, curing etc., complete complying with standard specification.

For Foundation and Basement

For superstructure in Ground Floor

For superstructure in First Floor

For Super structure in Second Floor

Ceiling Plastering with cement mortar 1:3 mix (one cement three P-sand), 10mm thick in all floors for RCC slabs, Beams, Sunshades including packing, providing cement mortar beading for sunshades, staircase steps, landing slabs etc., as directed by the departmental officers etc., complete complying with standard specifications.

Plastering with cement mortar 1:5 mix (one cement five P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification

Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster of paris, putty wherever required etc., complete as per standard specifications.

Supply and fixing of M.S Grills with Doors, Windows, Ventilators and Gates of required size suitable to site condition with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc., complete as per standard specification.

Supplying and fixing of Weldmesh Windows of best and approved quality using 'L' angles and flats of required size and fixing the mesh in position with necessary bolts and screws etc., complete complying with standard specification.

Supplying and fixing of terracotta jolly complete as per standard specification.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Window of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing in position of Aluminium anodised natural colour matt finish louvered Ventilator. The outer frame will be 62x38x2mm @1.174 kg/m and the louvers with moving arrangements will be made with aluminium channel of size 60x30x4mm @ 1.27kg/m with necessary 4mm thick glass pans for louvers, aluminium clips, Alu 'L' angle and metal screws including cost of labour for electrical consumption required for the fabrication, drilling holes in RCC columns with power drill to the required extent and make good to the original condition etc., complete and as directed by the departmental officers. The aluminium for frame to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns.

Painting two coats for New iron work surface using best quality synthetic enamel paint etc., complete complying with standard specification.

Painting two coats for Black Board surface using best quality Enamel Black Board Paint etc., complete complying with standard specification.

Paving the floor with 20mm thick Polished scratch proof 20mm thick SHAHABAD STONE SLABS with machine cut edges of size 2'x2' approved quality and colour in all floors over a base layer of cement mortar 1:3 [one cement and three M-sand] 20mm thick of walls and floors and pointed with the same colour cement neatly, including cost and conveyance of all materials and labour charges etc., complete complying with standard specification.

Paving the floor with 10mm thick Granite Tiles (Jet Black) (Super fine polished with Machine cut edges) in cement mortar 1:3 mix (one cement three M-sand) and pointing with white cement and colouring pigments to the colour of tiles including the cost of nosing, grooving etc., complete complying with standard specification.

Weathering Course with Brick jelly lime concrete made in Broken Brick Jelly 20mm gauge in pure slaked lime (no M-Sand to be added) laid over roof slab, the proportion of brick jelly to lime being 32 to 12.5 and well beated with wooden beaters for giving required slope and thickness etc., complete complying with standard specification.

Finishing the top of the roof slab with one course of Machine pressed tiles of size 20cm x 20cm x 2cm of approved quality laid in cement mortar 1:3 [one cement and three M-Sand] 12mm thick mixed with waterproofing compound 2% by the weight of cement used and the top pointed with same mortar etc., complete complying with standard specification.

Providing and fixing of PVC Rain water downfall pipe of 110mm dia 4kg/sq.cm with necessary teak wood clamps etc., complete complying with standard specification.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc., conforming to IS specification including primer coating and enamel painting as per design given by the departmental officers etc., complete as per standard specification.

Fabricating supplying and fixing of Galvalume Colour Sheet of size 0.47mm with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 gauge having width 1050mm. The sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws and plastic washer. The washer and screws to be fixed by using minute power machine drilled without damaging the sheets paint coating to be regular modified polyester coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like Malabar Mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point (for electronic regulator)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories in flush with wall with 150mm x 100mm x 75mm MS switch box with 3mm thick hylum sheet cover for 5A 3pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp

Supply and fixing of 4'40W twin street light fluorescent fitting complete with copper choke and condensor with 32mm dia GI pipe (Class 'B') with 1 No. 32mm GI bend complete on the existing post wall with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads MS clamps and aluminium painting with fluorescent tubes

Add GST @ 18%