Municipal Administration And Water Supply Department Tender

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Flooring finishing with first quality design ceramaic tiles of all colours of size 305cm X 305cm X 6mm laid in cement mortar 1:3 mix to 20mm thick and painting with white cement using 0.30 kg/1m2 including finishing the jointing and painting flush with tiles surface etc., complete - 10 m2

Supplying and fixing of AC Rainwater down fall pipes 10 cm dia with necessary specials, bend, clamp, screw, nails TW Plugs etc

Solid PVC door shutter using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fix in position including necessary furniture and fittings. The cover all size of top rail, Lock rail and bottom rail shall be 70mm x 45mm, with suitable rebate for housing the shutter

Daddoing the walls with first quality approved colour Glazed tiles of size 150X150X6 mm laid in cement mortar 1:2 mix to 10mm thick and painting with white cement using 0.40 kg/1m2 including finishing the jointing and painting flush with tiles surface etc., complete

European Water Closet (Colour) with 'P' or 'S' Trap with Double Flapped seat and seat cover with Brass Highes and 10 litre capacity PVC low level flusing tank with all internal fittings

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.

Painting with enamal paint two coats for new Iron work including one coat of priming coat and using the best quality Iron primer and best quality synthetic enamel paint etc complete complying with standard specification

Painting with plastic emulsion paint two coats over base coat for new plastered surface for using best quality and aproved colour of oil bound distemper conforming to ISI specification etc., complete complying as directed by the departmental officers as per standard specification.

Supply and fixing of TNEB meter Board suitable for 32A Single Phase service connection with 32A Fuse unit (500V)32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit.

Wiring with 2 x 1.5 sqmm (22 / 0.3) PVC insulated SC sheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe cealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For electronic regulator).

wiring with 2x1.5sq mm (22/.3) PVC insulated SC unsheathed copper conductore cable of 1100V Grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories in flush with wall with 150mmx100mmx75mm MS switch box with 3mm thick hylem sheet cover for 5A 3pin interlocking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed Plug point. (SD 12)

Supply and run of 2 of 4 sq.m (56/0.3)PVC insulated SC unsheathed CU.Conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(SD 44)

Supply and fixing of WT bulk head fitting with guard (Phillips/Bajaj/Crompton/K.Lite) Suitable for incandescent lamp with 11 Watts CFL Bulb Bulb(SD 83)

Supply and fixing of single box type 4"40W flu fitting completed with copper choke and condensor,with condult pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting with Tube (SD 87)

Supplying and fixing of 1200mm(48")sweep AC ceiling fan complete with stepped electronic 300W Regulator with 1 metre down rod with fan clamp with side plates and crpss arm of size 450mm(16") (SD 106)

Supplying and fixing of 400mm WALL MOUNTING FAN as per the direction of Departmental officers.,

Supplying and fixing of Crompton Storm 450 mm High Speed Pedestal Fan 1400RPM as per the direction of Departmental officers.,

Earthing as per the ISI specification with an earth electrode of 1 1mt class B GI pipe of dia not less then 40mm with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonery work and with 38mm RCC cover slab for the brick masonry (SD 233)

supplying and fixing of HDPE Water Tanks with suitable specials including cost of materials to site and all other labour charges.etc

S/F of RCC Ornamental Jolly as per direction of departmental officers etc,complete

Supply and Fixing in position of Indian make White glazed earthware WASH BASIN 550mmx400mm with all accessories such as costIron brackets , 32mm dia C.P waste coupling 15mm dia G.M wheel valve ,15mm dia Nylon connection , 15mm dia Brass Nipples, 15mm C.P Pillar tap etc., complete.

Supplying and Fixing of Stainless steel handrail including all labour charges and scaffolding work as per the direction of Dept. Off., etc. Complete

Supply and Fixing of 1HP Motor with pumpset as per Standard Quality as per the Direction of the Departmental officers etc., complete.