Municipal Administration And Water Supply Department Tender

Supplying and filling with M. sand in layers of 15cm thick including watering and ramming to consolidation including cost and conveyance of sand and filling etc complete as per standard specification

Plain cement concrete 1:5:10 mix using 40mm gauge hard brocken granite stone jelly for foundation and flooring including dewatering if found necessary and laid in layers of not more then 10cm thick well rammed and consoildated including curing etc., complete

Providing Steel Centering and Shuttering without strutting arrangements for RCC / PCC works upto 3m height including cost and conveyance of all materials at site and all labour charges and other incidental charges etc., complete complying with std. specification

Providing Steel Centering and Shuttering with strutting arrangements for RCC / PCC works upto 3m height including cost and conveyance of all materials at site and all labour charges and other incidental charges etc., complete complying with std. specification for Column

Supplying, cutting, bending, tying and fixing in position of MS / RTS grills for Reinforced Cement Concrete work including cost of steel & binding wire etc., complete.

Reinforced Cement Concrete 1:1.5:3 mix using 20mm ISS gauge HBBG metal excluding cost of reinforcement, centering and shuttering but including laying concrete curing, finishing etc., cost of all materials and labour charges etc., complete as per standard specification)

Basement

Refilling of Excavated earth inlayers of 15cm including watering ,ramming to well conolidation etc.complete

Brick work in cement mortar 1:5 mix using country bricks of standard size 8 ¾” x 4 ¼” x 2 ¾” etc., complete ( For Foundation and Basement)

Brick work in cement mortar 1:5 mix using country bricks of standard size 8 ¾” x 4 ¼” x 2 ¾” etc., complete (For super structure)

Supplying , fabricating ,erecting structural steel work for roofing welded or bolted type using MS channels ,angles ,plats and round bars etc., conforming to IS specification including primer coating and enamal painting as per design given by the departmental officers etc,. complete

Roofing with pre painted Galvanium sheet corrugated sheet 0.47mm thick with necessary bolt and nut and washer including cost of all materials and labour charges etc., complete

Plain cement concrete 1:2:4 mix using 20mm gauge hard brocken granite stone jelly for foundation and flooring including dewatering if found necessary and laid in layers of not more then 10cm thick well rammed and consoildated including curing etc., complete

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 gauge GI sheet.The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers,transportation charges etc., complete.

Pre - Painted Galvanized Iron Two Track Sliding Window : Providing and fixing pre- painted two track , two panel sliding system fabricated from roll formed sections made of galvanized steel powder coated ( Base steel as per IS 513 ' D ' quality , galvanized as per IS 277 with zinc of 120 grams / sqm . ) with total coated thickness of 0.58mm . Paint specification : Coated sections should be with primer coat of epoxy primer of 5-7 microns thick , finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns . Dimensions of sections : Section for frame two track should be of 59mm x 44mm , section for shutter should be of 35mm x 49mm for window , section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm . Fixing details : The frame and shutter sections should be cut to length , joined with corner brackets made of glass filled nylon . Ethyl Propylene Diamine Monomer ( EPDM ) Gasket should be used all around glass . Accessories : Corner brackets made of glass filled nylon gasket made of Ethyl Propylene Diamine Monomer ( EPDM ) . Locking system should be of single pin locking for Windows . Single wheel rollers for windows should be provided . Glass : Glass shutter and ixed glass portion should be provided with a glass of 4mm pinhead glass . Vindow frame should be fixed to brick / concrete masonry by using nylon self- xpanding caps and driving MS electro plated 80mm long screws into the caps Pough frames .

Plastering with CM 1:5 mix for 12mm thick etc., complete

Painting two coats with approved Emulsion paint over cement plastered surface ceiling and other new surface including cleaning prepering the surface and curing etc., complete

Painting with best synthetic enamel paint of approved Colour and high quality with two coats to new iron work etc. complete.

Wiring with 2 X 1.5 sqmm (22Nos/0.3mm dia) PVC insulated single core unsheathed copper conductor cable of 1100 volt grade in suitable PVC rigid pipes concealed in wall and ceiling with PVC accessories in flush with wall with 3mm tk hylum sheet cover with T.W. switch box and 5amps flush type switch and making good of the concealed portion with suitable colour for PVC open light/fan point (SD-24)

Wiring with 2 X 1.5 sqmm (56/0.3) PVC insulated SC unsheathed Cu. conductor cable of 1100 volt grade in suitable PVC rigid pipes in wall and ceiling with PVC accessories with 150x100x113mm T.W. switch box and 5amps 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the open plug point (SD-38)

Wiring with 2 X 1.5 sqmm (56/0.3) PVC insulated SC unsheathed Cu. conductor cable of 1100 volt grade in suitable heavy gauge PVC piope on wall and ceiling with PVC accessories with 150x100x113mm T.W. switch box and 15amps 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the open power plug point (SD-39)

Supply and run of 2 of 4 sq.mm (56/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade on 7/20 GI bearer wire for service connection mains SD No:65

Supply and run of 2 of 4Sqmm (56/0.3) PVC insulated SC unsheathed cu.Conductor of 1100V in 20mm dia GI pipe with suitable bend on both end for service connection mains SD-70

Supply and fixing of LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE)- 48W LED Street Light Fitting with LED etc., complete

Supply and fixing of vinyle name board of req size with corporation embalom in Tamil as directed by the departmental officers including framed with 50x25mm country wood reepers outer finished with 1”x1” Aluminium beeding with all material and labour cost for fixing etc., complete

Supplying and fixing 110mm dia PVC rain water down fall pipe including cost of 110mm dia PVC pipe, bend, tee, brackets and teak wood plugs etc., complete

Supply and filling of 40mm ISS Gauage HBBG Metal including cost of materials and labour charges for filling etc.complete as per std specification.

Supplying and laying wooden flooring at site 8mm thick of approved make using click laminated floor with inbuilt 3mm sound bloc class of use 31 water resistant AC 3 grade impact resistant IC3 (as per EN 130 900 / 1400) having 0.60mm MLC (Multi-Layer Guard + SRSG 2) (Scratch Resistant Surface Second Generation) on top of moisture high density fibre board substrate specially developed copr of plank size 1288 x 196 x 8mm having joints tongue and groove to secure long lasting joint. The tongue and groove having the edges duly pre impregnated with par affine including laying 0.20mm thick alkali resistant polyethylene sheet of density 850 kg / m3 beneath the laminated wooden panel to absorb the sound caused including labour charges, loading, unloading, transportation, etc., complete

Supply and fixing of 750mm dia R.C.C 1:2:4 mix of pipe collar with 30cm height and 5cm thick of ISI quality including transportation,loading and unloading and fixng inpostion as directed by the Departmental officers etc., complete as per std specification.

Providing and laying of 63mm thick high strength type of interlocking pavement block in required sizes of minimum compressive strength of 400 kg/cm2 in unipaver shape of approved make to be laid in lorrying bone pattern with approved nonsticking surface in the top the rate is including levelling the base, preparation of sub base with sand cushion 100mm thick, laying out the pavement, cut the pieces to fit the edge, vibrating the pavers, sweeping the sand grouting, providing transporting, loading, unloading and laying of paver block and Priming coat of red oxide painting as per standard specification