Municipal Administration And Water Supply Department Tender

Plain Cement concrete 1:4:8 [one cement, four M-sand and eight course aggregates] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification.

Random rubble masonry in CM 1:5 [one cement and five M-sand] for foundation and basement using best old rough and bond stones including simultaneous pointing above ground level with the same mortar etc., complete complying with standard specification.

Supplying and erecting centering including necessary supports for the plane surfaces such as Drainage & Culvert Retaining walls etc., using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding supported by casurina props of 10cm to 13cm dia spaced at suitable intervals etc., complete complying with standard specification.

Supplying and erecting centering including necessary supports for the plane surfaces such as RCC Column Footing, Plinth Beam, & Sill Beam etc., using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding supported by casurina props of 10cm to 13cm dia spaced at suitable intervals etc., complete complying with standard specificatio

Supplying and erecting centering for soffits of plane surfaces like RCC Slabs, Lintels, Sunshades, Square Columns, Staircase waists, Beams etc., including strutting 3m high using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with M.S angles of size 25mm x 25mm x 3mm laid over silver Oak (C.W) joists of size 10cm x 6.5cm (spaced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced of 75cm c/c) etc., complete complying with standard specification

Supplying, fabricating and placing in position of Steel Reinforcement using Mild Steel or Ribbed Tor steel bars for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete complying with standard specification

Providing and laying in position standardised concrete mix M-20 Grade in accordance with IS 456-2000 using 20mm and down graded hard broken jelly for all RCC items of works with minimum cement content of 3250kg/10cum and maximum water cement ratio of 0.50 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without impairing strength and durability with about (5.0cum) 7730kg of 20mm machine crushed stone jelly and with about (3.30cm) 5156kg of 10-12mm machine crushed stone jelly and with about (4.79cum) 7760kg of M-Sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing etc and providing fixtures like fan clamps in the RCC floor / Roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and directed by the departmental officers. The Coarse and fine aggregates to be used should comply with the requirements of IS standards.

Fly Ash Brick work In CM 1:5 mix using best Fly Ash Bricks of size 230 x 110 x 70mm including finishing, curing etc., complete complying with standard specification.

Supply and fixing FRP door shutter with frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of hold fasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., complete complying with standard specification.

Supplying and fixing in position White glazed earthenware Oriya type INDIAN WATER CLOSET of size 580mm x 440mm of approved quality with 'P' (or) 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring around the closet using 40mm broken brick jelly in lime concrete 1:2:5 mix (one lime, two M-sand and five brick jelly) 100m thick and finishing the top to the required slope and including giving necessary connection to the cast iron soil pipes / PVC pipes by dismantling the brick masonry, reinforced concrete roof / floor slab and making good the disturbed portion to original condition without any leakage etc., complete complying with standard specification.

Supply and fixing in position of 50mm thick RCC Jolly made in RCC 1:2:4 mix using 20mm size Hard Broken/Machine crushed Granite Stone Jelly including cost of moulding and excluding cost of steel reinforcement etc., complete as per standard specification.

Paving the floor with 8mm thick Joint free Rectified Glazed Ceramic Flooring Tiles of all colours in all floors over a base layer of cement mortar 1:3 [one cement and three M-sand] 20mm thick laid in-situ and pointed with the same coloured cement neatly, including polishing with electric polishers to a high degree so as to make it perfectly smooth and showing etc., complete complying with standard specification.

Dadooing the walls with Colour Designed glazed tiles of size 300mm x 200mm x 6mm of approved make and quality in cement mortar 1:2 mix [one cement and two M-sand] over 10mm base layer plastering and pointing with white cement neatly etc., complete as per standard specification.

Fabricating supplying and fixing of Galvalume Colour Sheet of size 0.47mm with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 gauge having width 1050mm. The sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws and plastic washer. The washer and screws to be fixed by using minute power machine drilled without damaging the sheets paint coating to be regular modified polyester coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like Malabar Mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers..

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc., conforming to IS specification including primer coating and enamel painting as per design given by the departmental officers etc., complete as per standard specification.

Painting two coats for New iron work surface using best quality synthetic enamel paint etc., complete complying with standard specification...

Ceiling Plastering with cement mortar 1:3 mix (one cement three P-sand), 10mm thick in all floors for RCC slabs, Beams, Sunshades including packing, providing cement mortar beading for sunshades, staircase steps, landing slabs etc., as directed by the departmental officers etc., complete complying with standard specifications

Plastering with cement mortar 1:4 mix (one cement four P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification..

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification.

Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster of paris, putty wherever required etc., complete as per standard specifications.

Construction of Inspection Chamber of 0.60m X 0.60m X 0.60m clear size including earth work excavation, base concrete of 50mm thick CC 1:5:10, 11.50cm thick brick work in cement mortor 1:5 (one cement five M-Sand) using best quality second class ground moulded bricks of size 9" x 4½" x 3", Inner, top and outer sides should be plastered with CM 1:3 (one cement three P-sand), 12mm thick and 50mm thick wearing coat 1:3:6 using 20mm metal should be laid over the inner flooring and the top covered with 50mm thick precast slab etc., complete complying with standard specification.

Supplying and fixing in position 110mm diameter PVC pipe FINOLEX (or) EQUIVALENT having pressure 6kg/cm² including fixing with necessary clamps, screws but excluding cost of such specials etc., complete complying with standard specification. (For Ventilating Shaft)

Add G.S.T. @ 18%