Municipal Administration And Water Supply Department Tender

Supply and Fixing of 3 Nos 6A two module 5 pin Socket, 3 nos 6A one module switch on Suitable module surface mounting Box (plastic) with moduler cover plate (plastic) on wall with earthconnection Higher end

Supply and fixing of 2 Nos 6/16A Two Moudle Socket, 2 Nos 16A one Module Switch with Moudle Cover Plate (Plastic) on Suitable Module Concealed Box (G.I) in Flush with Wall with Connection Higher End. SD 495

Supply and fixing of 20AmpsDP Plug and socket in sheet steel enclosure with 32 A DP MCB in flush with wall with earth connection. (Legrand (MDSS/Haser) (L&T ) (SD -140)

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40 A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (lik standard make) SD. 179

Supply and run of 2 of 4 sq.mm (56/0.30 PVC insulated SC unsheathed copper conductor of 1100v grade in suitable PVC rigid pipe concealedl in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the conceded Portion with suitable Colour (SD -57)

Supply and clamping of 31/2 x 25 sq.mm PVC LTUG armoured Alu. Cable on post or on wall with MS Clamps (SD-222)

Supply and clamping of 31/2 x 120 sq.mm PVC LTUG armoured Alu. Cable on post or on wall with MS Clamps (SD-222)

Supply and fixing of brass cable gland for 31/2 x 25 sq.mm PVC armoured LTUG Alu. Cable with earth connection (SD -186)

Supply and providing cable end termination of 31/2 x25 sq.mm PVC LTUG aluminium armoured cable with necessery Alu. Cable socket by crimping etc., with electrical connection complete. (SD -235)

Supply and clamping of 31/2 x 25 sq.mm PVC LTUG armoured Alu. Cable through suitable G.I pipe on wall with MS Clamps

Supply, fabrication, of 200A Capacity Dust and vermin proof cubical type metering panal board Size of 3480mm(L) x 1725mm(H) x 0.300mm (D) made up of 16 SWG CRCA sheet steel for outer body Doors, switch and KWH meters, Separation, supports and with supply and fixing of four pole MCB isolator, and re wireable fuse units with bus bar chamber complete with tinned copper flat for three phase and netrual with bus bar insulator complete with inter connection of WH meters, current carrying capacity multi standard PVC insulated copper wire between bus bar to WHM and WHM to cutout and MCB's tinned copper flat for earth bus runs all round the panel to provide earth connection by by No.8 SWG HDBC conductor to incoming Fuse and meter chamber bus The housing the accommodate 15 No's Three phase WHM 200A Fuse with 100A Neutral Link as incomer 40A FP MCB 15 No's (MDS/ Legrand/ Hager/ L&T) and with sectional cutout for 3No's of 32A fuse in 15No's as Section cutout for each service WH metering chamber cutouts chamber suitable for WHM connecting 3 phase 4 wire reading type meter chamber at the front for reading type meter chamber provided with 5mm thick transprant glass at the front for reading purpose with sealing provision by TNEB and supply the panel board should be painted two coats of High quality epoxy paint over one coat of red oxide primer with superscriptions the above cubical EB metering panel rest on Suitable angle iron base

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry . (SD -233)

Supply and run of 1 of No.8 SWG GI wire for earth connection. (SD -74)

Fabriction supply and erection of tobulor post with Truss (100mm, 80mm, 75mm) The Rate shall be include the cost of tobulor post Truss members, labour charges for manufacturing and erection and Painting etc., complete. as per departmental specification and drawings.

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Add GST 18%