Municipal Administration And Water Supply Department Tender

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and Eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for sides and soffits for plain surface such as slabs lintels sunshades staircase waist slabs etc., including strutting 3m high using M.S sheet of size 90cm X 90 cm and 10 Gauge fitted with M.S Angle of size 25x25x3mm laid over silver oak (C.Wood) joists of size 10x6.50cm spaced at about 90 c/c and supported by casurina props 10 to 13 cm dia spaced at about 75 c/c complying with standard specification.

Column

Grade Beam

Beams and slabs

Supplying, fabricating and placing in position mild steel or deformed steel bars for all Reinforced Cement Concrete items of work including cost of steel, transporting, straightening, cutting, bending, cranking, binding etc., including cost of binding wire etc., complete as per standard specificaitons.

Reinforced cement concrete 1:1.5:3 mix (One cement one and half sand three aggregate) using 20mm ISS gauge HBBG metal from the approved quarry including mixing, laying, consolidating, curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Brick work in CM 1:5 (One cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" x 43/8"x 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Foundation & Basement

Ground Floor

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete(S.No.20.0 TWAD 2022-23)

Fully panelled Single leaf Door (0.90 x 1.20 m)

Fully panelled Double leaf - Window(without Ventilator) (0.90 x 1.20 m)

Ventilator (0.60 x 0.45 m)

Supply and fixing of 25 mm thick Cuddappa Slab including cost of material and labour charges for fixing in position etc., complete as per standard specfication. (M - 0132 & M -0644 PWD SoR 2024-25)

Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering sand (P- Sand), 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar (1:5) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Corporation Engineer before use on work

Paving the floor with design Antiskid ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand), 20mm thick laid in-situ and pointed with same coloured cement

Weathering course with concrete broken brick jelly 20mm size in pure slaked lime (no sand to be used) over RCC roof slab the proportion of broken brick jelly to lime being 32:12.5 well beaten with wooden beaters giving required slopes and thickness etc., complete

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting with Enamel Paint over the New Iron works of approved quality and colour without priming coat including cost of all materials and labour charges etc.,complete as per standard specifications.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Wiring with 2x1.5sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5AFT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (5 points per coil) SD 18 - PWD Elec.Data 24-25

Wiring with 2 x 1.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mmx100mmx113mm TW switch box in flush with wall with 3mm thick hylem sheet cover for 5A 3pin non interlocking wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open PVC plug point SD 37 PWD Elec.Data 24-25

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting etc, complete as per standard specifications. SD 89-PWD Elec.Data 2022-23

Supply and fixing of 1200mm sweep ceiling fan including all material such as starter, Capacitor etc., with all labour charges etc., complete as per standard specifications SD 112-PWD Elec.Data 2024-25

Supply and Run-of 4.00 sq.mm GI service wire including cost of all material charges and labour charges etc., complete as per specifications. SD 65 -PWD Elec.Data 2024-25

Supply and Run-of 4.00 sq.mm (56/0.3) PVC inssulated SC unsheathed copper conductor of 1100 V Grade in 25 mm dia GI Pipe ('B' class) suitably bent at both ends with necessary angle iron upright and end supports for mains etc., complete SD 70 -PWD Elec.Data 2024-25

GST 18%