Municipal Administration And Water Supply Department Tender

Supplying and filling in foundation and basement with filling M.Sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four Crushed stone sand and eight aggregate) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

Beams and slab

For plane surfaces such as circular columns RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. (No separate payment will be made by the Department for the excess usage of materials)

Foundation

For Ground floor

For First floor

Supplying, fabricating and placing in position Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Ground floor

Providing and laying first quality of double charged vetrified tiles of all colours of size 600mmx600mmx8mm set in cm 1:3, 12mm thick including pointing with white cement, labour materials, etc(Relevent ISI STD

Supplying and laying in flooring with fully polished Sinthetic Grey colour Granite stone of 20mm thick (average) of 4' X 2' in size laid over base layer of cementmortar 1:3 (one cement and three Plastering sand) - 20 mm thick and applying cement slurry &pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers

Special Ceiling Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with Cement Mortar 1:5 (One cement and Five Crushed stone sand ), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

supply and fixing of commisioning of 12W Warm white LED Ceiling track light with drivers on false ceiling Including track etc all complete as required

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. -Electrical SOR - 24-25 - SD-440.

Supply , Installation, testing and commisioning of 30 W pendant light on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply , Installation, testing and commisioning of 100W LED Highbay light with suitable support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply , Installation, testing and commisioning of 30W, 6500k, IP44, A circular recessed LED luminaire with integral Dali Ballast etc all complete

supply and fixing of 120W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting . Including 6 meter pole

Supply , Installation, Testing and Commissioning of Linear LED Strip-lights (20W/M STRIP LIGHT (WARM WHITE ) ) for installing in False-ceiling Coves together with requisite driver etc. complete as required.

Supply & Installation of LED Bollard 11W± 10% , Integral type bollard cylindrical/Conical Shape, Die cast aluminum Housing , Dome shape , Top cover fixed with , Cylindrical/ Conical Shape acrylic cover Opal White Poly Carbonate Diffuser. SMD LED of 1 to 3 Watt each assembled on single MCPCB, Led Lamp lumens output with efficacy 80 lm/W, Rated Current 0.050 A, Lumen Output 800 Lm, Approx. Weight 2.0Kg , Driver PF 0.95 Luminaire having color temp up to 6500K & 50,000 Burning Hours. Life with minimum @ L 70, The color rendering index of LED light should be more than 70. Luminaire, conical Surface flux @ 120 Degree is 80 L/w, comprises of driver PF 0.95 & Surge Protection 3KV , IP65 Protection , Connection Wire, Testing etc. to complete the job having base plate with holes for direct mounting. Bollard LED 10 Watt cylindrical shape height 600mm, Color Temp 3000-6000k ±10%, Product Dimension Minimum - L- 600mm, D- 140mm (± 10%) MAKE:- Philips, Jaguar Lighting, Crompton ,Bajaj, orient or from the approved

Supply and fixing of 4 nos.6/16A two module socket , 4 nos. 16A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Stair case Light point Higher End

Supply and fixing of 13A Twin Socket Floor Box with Data with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of 15A Sockets with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of Floor Box with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of 20A SP Isolator with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board (with MCCB incomer) with double door (metal door) with 1 no. 250A 4P MCCB switch as incoming and 3 nos. 63A 3P MCB , 3 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on suitable angle iron frame on wall with earth connection only. Higher End

Supplying and fixing of 1 No three phase distribution board with 4 way/ phase andd 32 away with neutral link onn a sutiable well varnished teak wood plank inculding necessary innterconnections and earth connections cost of all materials etc. all complete

Supply and fixing of 6 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 18 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Earth pit using machinery (Back Hoe), including Hire charges, fuel charges and Supply of Tree guard, Wooden cauge, green cloth, Guard stick and Manure (Fertilizer) including cost, conveyance, loading, unloading and all other labour charge etc., complete. (for Avenue Plantation)

Supply and Installtion of Power cables with Earthing cable 4C x 120 SQ.MM AL XLPE/SWA/PVC/CU cable + 1C x 70 mm2 AL G/Y ECC (EB MAIN TO MDB) (This length is tendative)

Supply and Installtion of Power cables with Earthing cable 4C x 10 SQ.MM AL XLPE/SWA/PVC/CU cable + 1C x 10 mm2 AL G/Y ECC (MDB to DB-L & DB-P)

Supply and Installtion of Power cables with Earthing cable 4C x 75 SQ.MM AL XLPE/SWA/PVC/CU cable + 1C x 35 mm2 AL G/Y ECC (MDB to VRF-ODU-01 ISO)

Supply and Installtion of Power cables with Earthing cable 4C x 6 SQ.MM AL XLPE/SWA/PVC/CU cable + 1C x 6 mm2 AL G/Y ECC (MDB to Entrance Signage ISO )

Supply and Installtion of Power cables with Earthing cable G I Cable Tray (300x50mm)

Man hole Cover 600mmx 600mm

FiberGlass tank for Fish Recovery - 9000Ltr

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. (Gate Valves 25mm)

O) Providing and fixing 2'' High pressure uPVC pipes (Soil and waste line) of required diameter conforming to I.S.-13592, and I.S.-4985 to withstand continous internal hydroulic pressure of 6 kg/cm2 including necessary fixtures and fittings, such as bends, tees, single junctions, double junctions and joining with rubber rings and lubricants, on wall by means of clips or in ground including necessary excavation, laying refilling, trench testing etc. complete.

Supply, erection, testing and commissioning of Gun Metal Non-Return Valve of size 50mm dia including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Manufacturing, supply and delivery of resilient seated wafer type butterfly valve 50mm in accordance with EN 593, centric disk mounted in three maintenance-free bearing bushes, tight in both flow directions, Replaceable rubber sleeve with integrated seal for functionally reliable use for flared flanges, welding flanges, PE flanges as well as loose flanges with V-collar, Stable seat due to collar with vulcanized support ring. Vaccum tight upto 1 Torr. Face to face length acc.to 558-1, basic series 20(DIN 3202/k1). With Electrostatic epoxy powder coating (EP-P) inside and outside color blue RAL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy Powder should be approved by W 270.(EP-P it is resi-coat powder approved for drinking water application, applied through fusion bonding technology process by dipping the shot-blasted casted components heated upto 200 deg C) and with 5 years -

Manufacture, Supply and Delivery of Tamper proof DI single chamber double orifice, triple function (ventilating, admitting and venting during operation) air release valves with pressure range from PN 1.0 to 2.5 with body and cover made of Ductile Iron of Grade GGG 40 or equivalent grade conforming to IS 1865 with Food Grade Epoxy Powder coating(EP-P) inside and for outside of colour blue RAL 5005. All internal parts such as float, shell etc., cover bolts, made of Austenitic alloy steel of SS AISI 304/316. The float shall be made of Polytetrafluroethylene/ Austenitic alloy steel of AISI 304/316. Gaskets and seals of EPDM / Neoprene rubber for TWAD Board works anywhere in Tamil Nadu and with 5 years warranty (Air release Valve -25mm )

Supply and erection of 3.Hp Submersible Pump set using nylon rope including cost of motor , fixing necessary cable charges and labour charges etc., complete

UPVC-Drain pipe (H) -110MM dia

UPVC-Drain pipe (V) -75 MM dia

Supply,install,testing & commissioning of Indoor ceiling mounted cassette units including hard refrigerant pipe work, thermostats, valves, fittings, R-410A refrigerant gas,High pressure drain pipes with Utrap to nearest floor Trap, all in accordance with the Drawings and Specification. Allow for all condensate drain pipework With Drip tray .

360° CASSETTE - CAPACITY : 4.0 TR

360° CASSETTE - CAPACITY : 3.2 TR

DECORATIVE SPLIT UNIT - CAPACITY : 1.6 TR

VRF-ODU-01 CAPACITY :- 90HP

Thermostat

ERV UNIT - CAPACITY : 3 TR, 588 CFM

Supply and fixing of POE 16 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and Fixing of Rack with Accessories -Higher end 36 U Rack with LNS unit and fan extra for the above rack.

55" LED Screen for cctv Monitoring - Operating System: Tizen Resolution: Ultra HD (4K) 3840 x 2160 Pixels Sound Output: 20 W Refresh Rate: 50 Hz

G I Pole for CCTV Camera - 4Mtr height

Providing and fixing of Digitally Printed Retro Reflectorized Sign Board using UV Inkjet Printer made out of cube corner micro prismatic grade sheeting of Type-XI standards of IRC 67-2012 and ASTM D 4956 – 09 specification, Digitally Printed using UV Inkjet Printer (UVIJ) for traffic colour, images/ logos/ text and laminated with clear electrocuttable film and applied to properly prepared sign substrates, fixed over 2mm Aluminium sheet with back supporting frame of 50x50x6mm Mild Steel ‘L’ angle and supported on a 150NB (Nominal Bore) pipe with 4.50mm thick with an overall height from top of the board to foundation. The sign board should be of 2.10m clear height from the ground level to the bottom of the sign board and 1.10m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete of size 450x450x1100mm including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete. The Micro prismatic sheeting should have minimum 70% co-efficient of Retro-reflection values as per table 6.90 of IRC 67-2012. The retroreflective sheeting shall be covered under 10 Years warranty issued for field performance and a certified copy of 3 years outdoor exposure report shall be obtained as per IRC 67-2012. The warranty shall be inclusive of digitally printed images/ logos/ test/ legends and their bonding to the retro-reflective sheeting (as per MoRT&H specification no.801) of Size – 3.64m x 2.42 PWD SOR P.NO : 290 HW-W0098

First Aid Box complete with all First Aid Medicines PWD SOR Page 142. Sl.No.8c

4 Nos of Fire Buckets made out of 40x40x6mm MS Angle PWD SOR Page 142. Sl.No.8e

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers. PWD SOR Page No. 81. Sl.No.330

glass hand rails with 12mm clear toughened glass, top railing pipe and 8'' spicot aluminium black colour

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames. Glass: 5mm reflective Saint Gobain OR equivalent. M-0671 SOR 24-25 PG .NO : 107

For GST 18%