Ministry Of Road Transport And Highways Tender

Providing and laying Prime Coat over WMM surface using 6 Kg of Emulsion Bitumen (SS1) per 10 sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 502 of MoRT & H Specification Rev-5

Providing and laying Tack Coat over WMM surface (treated with primer) using 2.50 Kg of Bitumen Emulsion (RS1) per 10 sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 503 of MoRT & H Specification Rev-5

Providing and applying tack coat over Existing BT surface with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 Kg/sqm on the prepared bituminous / granular surface cleaned with mechanical broom.

Providing and laying Dense Bituminous Macadam Grading II using 37 Kgs of VG40 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 50mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 504 of MoRT & H Rev-5

Providing and laying Compacted Bituminous Concrete to 40 mm thick using of CRMB 55 grade bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, conveying the mix to paver site, spreading the mix to uniform thickness with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for CMP with bitumen boiler, tipper trucks, Paver Finisher Vibratory / Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MoRT & H Rev-5

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2 of MORT & specification.

Providing VRCC M35 mix using 20mm, ISS HBG metal centre median of size 0.650m at bottom 0.250m at middle 0.150 at top and to height of 0.860m from the road level including cost and conveyance of all materials to work site and providing form work for shuttering on both sides and chambered edged at top, including cost of steel reinforcement as per the bar bending. Rendering smoothness over the CC surface with 10kg of cement for 10 sqm area and painting two coats over the CC surfaces with best approved quality of synthetic enamel paint including primer etc. including all labour charges, hire and fuel charges for the tools and plants employed and as per the standard specification and in accordance with the drawings appended here with and as directed by the departmental officers etc. complete.for Crash Barrier type Centre Median

Providing and erecting of Retro Reflectorised Cautionary, Mandatory and informatory sign(Without definition Board) made out of High intensity Prismatic grade sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminum sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mm x 75mm x6mmwith a clear height not less than 2.1m from the ground level to the bottom of the sign board and 0.6 m below ground level.The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60 cm, size including cost and conveyance of all materials, equipments Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro -Reflectro sheet shall consist of minimum coefficient of Retro -reflection as per table 6.6 of IRC 67-2012. The retro reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (as per MORT&H specification No 801) (90cm equilateral Triangle Board)

Providing and erecting direction and Place Identification retro - reflectorised sign made out of cube corner Micro Prismatic grade sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminum sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mm x 75mm x6mm with a clear height not less than 2.10m from the ground level to the bottom of the sign board and 0.6 m below ground level.The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60 cm size including cost and conveyance of all materials, equipments Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. Micro prismatic grade Retro-Reflectro sheet shall consist of minimum coefficient of Retro -reflection as per table 6.9 of IRC 67-2012. The retro reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (as per MORT&H specification No 801) for location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications., sign having area upto 0.9sqm Type-XI

Providing and erecting direction and Place Identification retro - reflectorised sign made out of cube corner Micro Prismatic grade sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminum sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mm x 75mm x6mm with a clear height not less than 2.10m from the ground level to the bottom of the sign board and 0.6 m below ground level.The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60 cm size including cost and conveyance of all materials, equipments Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. Micro prismatic grade Retro-Reflectro sheet shall consist of minimum coefficient of Retro -reflection as per table 6.9 of IRC 67-2012. The retro reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (as per MORT&H specification No 801) for location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications., sign having area above 0.9sqm Type-XI

Providing and erecting direction and Place Identification retro - reflectorised sign made out of cube corner Micro Prismatic grade sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminum sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mm x 75mm x6mm with a clear height not less than 2.10m from the ground level to the bottom of the sign board and 0.6 m below ground level.The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60 cm size including cost and conveyance of all materials, equipments Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. Micro prismatic grade Retro-Reflectro sheet shall consist of minimum coefficient of Retro -reflection as per table 6.9 of IRC 67-2012. The retro reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (as per MORT&H specification No 801) for location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications., sign having area above 0.9sqm Type-XI

Providing and fixing of Retro Reflectorised Cautionary Mandatory and informatory sign made out of High intensity Prismatic grade sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminum sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mm x 75mm x6mmwith a clear height not less than 2.1m from the ground level to the bottom of the sign board and 0.6 m below ground level.The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60 cm, 60cm size including cost and conveyance of all materials, equipments Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro -Reflectro sheet shall consist of minimum coefficient of Retro -reflection as per table 6.6 of IRC 67-2012. The retro reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (as per MORT&H specification No 801) Chevran Board

Providing and laying of Hot Applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level uniform and free from streaks and holes etc complete as per MORT&H specification 803.

Providing and fixing of Reflective Road Studs of 'Category A' Raised pavement markers made out of poly carbonate/ methyl methecrylate/ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromatically values confirming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular No RW/NH 33023/10/97-DO III dt 11.06.97. The height, width and length shall not be less than 15mm , 90 mm and 100 mm with minimum reflective area of 13 sqcm on each side and slope to the base shall be 35+/- 5 degree.Each reflector shall have a CIL not less than vlues specified in Table 2 of MORTH circular.The strength of detachment of the integrated cylindrical shanks (of diameter not less than 19+/- 2mm and height not less than 30+/-2 mm) from the body is to be a minimum value of 500kgf, Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manfacturer's recommendation and complete as directed by the Engineer, The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC 35-2015 guidelines and MORTh specification 804 etc., complete

Providing and Fixing of Rigid Median Marker double sided made of tough, high impact resistant, injection - molded, thermoplastic body with an isoscelestrapezoidal structure of length, width and height not less than 15cm, 10cm and 10cm respectively and thickness not less than 1.8mm, the body structure shall be rounded at its acute angle, all the corners and edges. The plastic used for molding the Median Marker shall be a minimum Notched Izod Impact strength value of 600 J/m at room temperature, when tested in accordance with ASTM D256 and shall retain at least 70% of this value when subjected to accelerated weathering for 1000hrs as per ASTM G155 or UL746c. The logo of the manufacturer shall be embossed on either side of the body in the injection molding process. The Median Marker shall have rectangular - shaped, fluorescent yellow color retro - reflective sheeting of size not less than 8.5cmx8.5cm and with fully reflective micro prismatic cube corners as its retro reflective elements as per IRC 67 2012 and ASTM D4956-09 type XI specifications reflectivity values. The retro reflective sheeting shall be both sides of the Median marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, etc. The Median Marker shall be fixed by a combination of Epoxy adhesive and grouting.

Provision of Solar Blinkering Light

Construction of Retaining wall at Km 91/6 - 91/8 L/S (3.5 m Height) of Kollam - Thirumangalam Road NH 208-Earth work in excavation for foundation of structures as per drawing and technical specification including setting out construction of shoring and bracing removal of stumps and other deleterious matter, dressing of sides and bottom, back filling with approved material for foundation for abutments and return wall as per MORT & H specification.

Vibrated Cement Concrete of Grade M15 (Nominal Mix 1:2:4) using 40mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting,laying and curing concrete, working at depths, Tools and Plants and incidental Charges such as maintaining of protective bund, cofferdams, shoring, strutting etc.,complete as per relevant standard specification for Foundation (below sill).

Vibrated Cement Concrete of Grade M15 (Nominal Mix 1:2:4) using 40mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting,laying and curing concrete, working at depths, Tools and Plants and incidental Charges such as maintaining of protective bund, cofferdams, shoring, strutting etc.,complete as per relevant standard specification for Above Sill Level.

Filling with clean gritty gravel around the pipes including cost and conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density including watering, with all leads for water and all other incidental charges etc, complete .

Providing and fixing PVC seepage pipes of 100mm of required lengths for abutments and wings including cost and conveyance of all materials to worksite and labour for 900mm dia semipherical backfill arrangements with 100cm size broken granite chips at the periphery and labour charges for fixing etc., complete to drain the backfill as per standard specification.

Providing and fixing Bituminous pad expansion joint 20mm thick including cost ans conveyance of the same to work site labour charges for fixing in correct position and all labour charges etc.complete

Supply of HYSD steel Fe 500 D for Reinforcement for RCC work including bending, placing and binding etc., for Deck slab, Bed Block & surface Reinforcement.