IREL India Limited Tender

Earthwork excavation for foundation in all types of loose/hard soil and depositing the spoils with an initial lead of 20m and lift upto 2m including refilling etc. by means of manually/ mechanically complete as per the direction of the Engineer-in-charge.

Earth filling for foundation/ flooring work using departmental sand including all transportation of filling sand/ building debris from HUP to site, levelling works, compaction, consolidation, etc. by means of manually/mechanically complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying and spreading of 150mm consolidated thick gravel of approved quality above the refilled earth surface with watering, levelling works, compaction and consolidating, etc. by means of mannually/mechanically complete as per the direction of Engineer-in-charge.

Supplying, providing and laying soling stone 300mm thick over the existing sub base/sub grade including levelling and consolidation to form a compact surface using hard blue granite soling stone including hand packing, wedging them tightly and filling the voids with loose sand, watering and sweeping the sand into the joints so that the hole is formed as solid mass, etc. complete as per standard specification and as per the direction of Engineer-in-charge.

Supplying, providing and laying PCC 1:4:8 mix for foundation/ flooring work using 40mm and below grade hard blue granite jelly including all form works, mixing, laying, compaction, consolidation and curing, etc. complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and laying PCC 1:2:4 mix for foundation/ flooring work/kerb wall drainage wall using 20mm and below grade hard blue granite jelly including all form works, mixing, laying consolidation and curing, etc. complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying, providing & laying RR masonry foundation/ wall/ retaining wall in cement mortar 1:6 for construction of wall using hard blue granite stone, etc. complete from 2.5 m below ground level to 4.5m height above ground level with neat finishing including proper pointing & necessary scaffolding work etc complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and laying dry rubble masonry for soak pit for construction of wall using hard blue granite stone, etc. complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and laying solid block brick masonry in CM 1:6 using cement concrete solid blocks of minimum size 400*200*150mm for superstructure walls upto 4.5m height from ground level including mixing and conveyance charges and all scaffolding, staging, curing, etc. complete complying with standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and laying brick masonry in CM 1:6 using well burnt country brick of minimum size 22.9x11.2x7cm for foundation/kerb wall/wall upto 4.5m height from ground level including all scaffolding, staging, curing, etc. complete complying with standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and fixing twisted reinforcement IS 1786 HYSD bars Fe500D/Fe550D (TMT bars - TATA/ Agni/ JSW) including fabrication, cutting, bending, cold tying, with overlapping to the standard length wherever necessary and placing the reinforcement in position as per the direction of Engineer-in-charge including binding, provision of spacer bars, cover blocks and all other incidental charges, necessary scaffolding, staging, safety arrangements, etc. complete for all RCC works (item No. 15) upto 4.5m height as per standard specification and as per the direction of Engineer-in-charge.

Supplying, providing and laying cement concrete 1:1.5:3 for RCC works height upto 4.5m for foundation/retaining wall/slab/column encasing of rolled steel section using 20mm and below grade hard blue granite jelly with specified reinforcement (rate excluding the cost of reinforcement) and all mixing, laying, compaction, leveling, consolidation and curing, etc., including the cost of centering/shuttering work, necessary scaffolding, staging, safety arrangements, etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, plastering with CM 1:4 mix 15mm thick one coat floated hard & trowelled smooth etc. for floors & walls upto 4.5m height with neat finishing and necessary grouting, scaffolding, staging, safety arrangements, including fibermesh wherever required, etc. complete complying with standard specifications and as directed by the Engineer-in-charge.

Supplying, plastering with CM 1:3 mix 12mm thick one coat floated hard & trowelled smooth for RCC beam, column, ceiling, wall & floor upto 4.5m height with neat finishing and necessary grouting including all scaffolding, fibermesh wherever required, etc. complete complying with standard specifications and as directed by the Engineer-in-charge.

Supplying, providing and laying with 10mm thick vitrified/ Marbonite double charge tiles of size 1200mmx 600mm Kajaria/ Somania /Qutone brand with Cement Mortar 1:2 and pointing including finishing the joint and pointing flush with the surface, etc. complete as per specification and as directed by Engineer-in-charge.

Supplying, providing and finishing the floor with Somania/ Kajaria/Qutone make Anti-skid ceramic tiles of size 300mm x 300mm of approved quality and shade in CM 1:3 – 15mm thick and pointing the tiles with matching colour cement, etc. complete as per the direction of the Engineer-in-charge.

Supplying, providing, laying, dadoing the walls with Somania/Kajaria/Qutone make ceramic wall tiles of size 450mm x 300mm of approved quality and shade fixing with CM 1:2 – 10mm thick, etc. including neat cleaning, grouting and finishing with shaded colour joint filler, etc. complete as per the direction of the Engineer-in-charge.

Supplying, providing, laying, dadoing the floors with Somania/Kajaria/Qutone make teracotta pattern floor tiles (matte finish) of size 300mm x 300mm of approved quality and shade fixing with CM 1:2 – 10mm thick, etc. including neat cleaning, grouting and edge finishing with shaded colour joint filler, etc. complete as per the direction of the Engineer-in-charge.

Supplying, Providing and fixing 18-20mm thick jet black/coffee brown/ tan brown granite slab for wash basin/kitchen/store room/class room bench area including grinding & finishing the ends with half round and closing the joints with matching colour cement and polishing the slab to smooth finish, etc, complete as directed by the Engineer-in-charge.

Supplying, providing and fixing Sintex make PVC door of size 750mm x 2100mm including hinges, handle and locking arrangements, etc. complete as per specification and as per the directed by Engineer-in-charge.

Supplying, providing and fixing the CP sanitary fittings: Parryware Bib cock with necessary accessories as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP sanitary fittings: Parryware Pillar tap with necessary accessories as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP sanitary fittings: Angle valve with necessary accessories as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP & sanitary fittings: PARRYWARE TOWEL RAIL 600mm with necessary accessories as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP & sanitary fittings: SS 304 Kitchen wash basin of size 22"x18" (Metro/Prince) with necessary accessories (waste coupling, waste hose) etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, providing, fixing brass ball valve 3/4" with necessary fittings, welding, scaffolding arrangements, etc. complete as per the direction of Engineer-in-charge.

Supplying, providing, fixing brass ball valve 1" with necessary fittings, welding, scaffolding arrangements, etc. complete as per the direction of Engineer-in-charge.

Supplying, providing, hoisting and fixing of roof trusses including purlin, rafter, sleeves false rafter, base plate bracing and lacing, etc. fabricated out of G.I tubular square/rectangular heavy (C-class) pipes (purlin-1 1/2"; rafter - 1 1/2"; bracing -1") (TATA/Jindal) conforming to relevant I.S. code and providing G.I. tubular square/circular post heavy (C-class) (2.5"x2.5") (TATA/JINDAL) and proper welding with base plates and base fixing with concrete including painting with two coats of approved enamel paints (Asian/Berger/Nippon) over a coat of zinc chromate primer etc. complete. Over the roof truss fixing with 0.47mm thick powder coated sheet/ powder coated end curved sheet [TATA - Durashine /HINDALCO] (blue / red) with proper slopping, necessary ridges and drain arrangements, around side cladding and fixing 8mm dia G.I. polymer coated bolts & nuts (Aargee Associates/equivalent make), washer and bolt cap, necessary fittings with necessary valley gutter arrangements, etc., complete as per the direction of Engineer-in-charge.

Supplying, providing and laying PCC 1:2:4 mix for roof terrace flooring/ sunshade/ inner side of parapet wall work using 6mm chips and below grade hard blue granite jelly and providing 2 coat of polymer coating [Water Proof Coating (Sika/Perma) as per the desired ratio of manufactured product - The mix shall be stirred thoroughly until no bubbles remain in the mix, any lumps found in mix shall be removed. Apply first coat of polymer (water proofing agent) modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat etc.] for said portion, before applying water proof coating the surface shall be cleaned and remove all dust, foreign matters loose materials or any other deposits of contamination by rubbing with wire brush, etc. and all form works, mixing, laying consolidation and curing with necessary scaffolding upto 5m height from ground level, etc. complete as per standard specifications and as directed by the Engineer-in-charge.

Supplying & fixing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (UPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The door system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The door should be designed such that the water drainage does not pass through the reinforcement chamber. The door system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plugwith door closer, etc. complete as directed by Engineer-in-charge.

Supplying, providing and laying 20/25/32mm ID PVC finolex/ Ashirvad/Astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of Engineer-in-charge.

Supplying, providing and laying 40/50/63mm dia ID PVC finolex/Ashirwad/Astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement etc. complete as per the direction of Engineer-in-charge

Supplying, providing and laying 110mm dia ID PVC finolex/Ashirwad/Astral (6Kg) pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of Engineer-in-charge.

Supplying, providing and fixing of 6mm thick aluminium grill of standard pattern (diamond shape) including 'F' (or) 'H' section frame with necessary accessories including cutting, grinding, conveyance, etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, providing and fixing 50/60mm thick coloured (red/yellow/black/Grey) square shape concrete paver block of size 300mmx300mm pattern floor, bottom laying with 6mm jelly with 50mm thick over the earth surface including levelling the earth surface with neat finishing, side packing etc. complete as per the specification and as per the direction of the Engineer-in-charge.

Supplying, providing and fixing the CP & sanitary fittings: Parryware Wall Mounted Basin (Ultra White JOY Model No. C042B1C) with necessary accessories (waste coupling, waste hose, etc.) as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP & sanitary fittings: Parryware Ceramic Sanitary ware Indian Toilet/Orissa Pan with required trap and Slim Flush Tank Combo Pack (Standard, White) (23 Inch Indian Toilet) etc. as per the direction of Engineer -in-charge.

Supplying, providing and fixing the CP & sanitary fittings: Elite [EUROPEON CLOSET] WHITE PARRYWARE SINGLE PIECE SUITE 525x380x400mm including Seat cover, with required trap and slim flush tank (standard-white) and fittings as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP & sanitary fittings: PARRYWARE HEALTH FAUCET with HOSE & HOOK as per the direction of Engineer-in-charge.

Supplying, providing and fixing the CP sanitary fittings: Parryware Push cock with necessary accessories as per the direction of Engineer-in-charge.

Supply of paints and painting two coat with emulsion paint (Asian/Berger/Nippon) 1st quality of approved shade over a coat of cement primer for the external/internal masonry surface upto 10m height and above from ground level, including thorough scrapping, cleaning, removal of dirt, all tools & tackles, sandpaper and scaffolding arrangements, etc. and applying putty touch-up works wherever required, etc complete as per specification and as per the direction of Engineer-in-charge.

Supply of paints and painting one coat with emulsion paint (Asian/Berger/Nippon) 1st quality of approved shade over a coat of cement primer for the external/internal masonry surface upto 10m height from ground level, including thorough scrapping, cleaning, removal of dirt, all tools & tackles, sandpaper and scaffolding arrangements, etc. and applying putty touch-up works wherever required, etc complete as per specification and as per the direction of Engineer-in-charge.

Supply of paints and painting two coat with 1st quality enamel/touch wood paint of approved shade (Berger/ Asian/ Nippon) matching to the existing for all doors, windows, false ceiling, etc. including thorough cleaning and removal of dirt and applying wood sealer/primer and putty wherever required including necessary scaffolding arrangements, etc. complete as directed by the Engineer-in-charge.

Supplying, providing and fixing 500 ltrs. capacity Sintex water tank with all inlet and outlet pipe fitting arrangements and 20mm brass float valves, ball valve, etc., complete as per the direction of the Engineer-in-charge.

Supplying, providing and fixing M.S. grills/window/door of required pattern in frames of windows/Doors/grill etc. with M.S. flats, square or round bars including painting with two (2) coats of enamel paint (Berger/Asian/Nippon) over a coat of zinc-chromate primer (Berger/Asian/Nippan) and cutting, grinding, conveyance, welding charges, electrical charges, etc. complete as per the specification and as directed by the Engineer-in-charge.

Supplying, providing and fixing of 1 HP Texmo/ CRI domestic self priming pump with all inlet and outlet pipe fitting, necessary valve arrangements, etc., complete as per the direction of the Engineer-in-charge.

Supplying, providing, laying and fixing electrification concealed (polythene pipe)/open point with required wire (make: Finolex/Havells/Polycab), switch box, switches (Make: Polycab/ Havells) with all required necessary fittings including chipping, routing, clamping and all other incidental charges, etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, providing and fixing of Led tube light 22W (Havels/Wipro Garnet) with all required necessary fittings etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, providing and fixing of exhaust fan 375mm (15") Sweep (Heavy duty) with all required necessary fittings etc. complete as per the specification and as per the direction of Engineer-in-charge.

Supplying, providing and fixing of brown/white colour ceiling/wall fan 1200mm high speed energy efficient 53W fan (Crompton/Havells) with all required necessary fittings etc. complete as per the specification and as per the direction of Engineer-in-charge.

Engagement of Fitter for miscellaneous works complete as directed by the Engineer-in-charge.

Engagement of Mason for miscellaneous works complete as directed by the Engineer-in-charge.

Engagement of labour (Mazdoor) for miscellaneous work complete as directed by the Engineer-in-charge.