Indian Institute Of Information Technology Design And Manufacturing Tender

Providing and fixing cement bonded wood particle board as per IS: 15786:2008 of approved brand and shade, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Make : Bison panel or equivalent

Providing and fixing cement bonded wood particle board as per IS: 14276 of approved brand and shade, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge including wrapping the exposed surface of board with Fabric of approved quality and colour. (Cost of Fabric shall be paid for separately).

8mm thick cement bonded wood particle board without lamination as per IS: 14726 Make : Bison panel or equivalent

Providing and fixing of Fabric of approved quality and colour over the cement bonded particle board fixed in the modular partition. (For measurement purpose only exposed area shall be measured)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural, drawings and the directions of engineer-in charge (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm Make : Saint Gobain / Modiguard.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (All fittings to be paid separately).Make : Saint Gobain / Modiguard.

A Providing and fixing fittings for frameless toughened glass door / glass partitions of approved brand such as KOHLER, HAFELE etc as per the direction of engineer in charge.

Bottom patch fitting for 10-12mm glass, SS Matt finish

Top patch fitting for 10-12mm glass, SS Matt finish

Fanlight Pivot patch fitting for 10-12mm glass,SS Matt finish

Single connector side connector to hold fixed panels or support fin bracket for 10 to 12mm Glass, SS matt finish.

Centre patch lock with cylinder for 10-12mm glass, SS matt finish

H-pull handle back to back fixing 25mm dia x 305 C/C 450 O/A for 10-12mm Glass, SS matt finish

Double action floor spring (FS 2104) with 90 degree hold open and SS cover plate, size 4. Max, door leaf weight 120kg, SS matt finish, for door width 900-1200mm each

Providing and fixing of Pantry Cupboard Rack of length 6.3m and height being taken as 0.9 m on one side of the wall. The bottom of the cupboard rack to be made with 19mm thick commercial plywood of size 1.20 x 0.60 m both inside and outside shutters and approved Laminate. The remaining portion to be made with 0.60 x 0.60 x 0.60 m 10mm thick toughened glass shutters for keeping the Vessles. The rate also includes necessary hardware accessories both for the plywood and glass portion. The work to be executed as per the layout and the directions of the Engineer-in-charge. Make : Saint Gobain Make plywood: Merino/ Greenply or Equivalent. Note : The Measurements of the Cupboard will be taken in outer Length and Height

Providing and fixing folder roller blinds of approved design and colour all complete below mentioned specification as per the direction of Engineer-in-charge . Control Unit: This is made of high strength reinforced plastic. The clutch is Wrap spring design. The springs provided to transmit the driving & driven members of clutch. Clutch is operated directly use of endless beaded chain. IDLER: This is a high strength reinforced plastic. It is mounted plastic lock. The plastic lock provides smooth, free, quit & long wearing operation. Head Rail: This is an aluminum powder coated.contol unit&idler mounted on head rail with powder coated M.S.Brackets Roller Tube: contol unit&idler fixed to the either ends of the tube.the tube with heavy duty adhesive tape. Bottom Rail: aluminum rail with a groove for fixing the fabric powder coated. Bottom of the fabric & the purpose of it is keep the fabric in tension and straight.the end caps of the tube are ABS. Operating Chain: This is made plastic beads molded on thick polyester chord. The pitch of the beads is 6mm.the chain drives the control unit to close and open the blind. Fixing Brackets& Clamps: Fixing the blind using wall or celling.L’bracket is made of mild steel & zinc plated. Clamp is made of spring steel (0.7mm thickness) & zinc plated. Fabric Specification: Polyster fabric, material cal be washed on both sides with mild detergent.

Providing and fixing wallpaper of approved make and attractive design and colour as directed by the Engineer in charge (Note. The rate inclusive of scrapping, touchup putty, pest control powder with fevical, required hardware and labours, etc)

Supply, drawing, termination and testing of following sizes of FRLS or FRLSH, PVC insulted multistranded copper conductor wire should be in line with the incoming phase colour, 1.1KV grade in existing surface / recess / PVC conduits, including floor cutting & finishing by placing of all the accessories & lugs as per the requirement complete etc., Make: Finolex/ Polycab/ RR kabel/ Havells

1C x 4 Sq.mm (1-ph)

Red/Yellow/Blue

Black

Green

Dismantling, shifting & installation of existing 1200 mm sweep ceiling fan along with down rod, modification of wiring, supply & fixing of new safety rope, canopy set, clamp set, bolt, nut & fastners etc shall be fixed in surface /recess including drilling & finishing in the wall as required. Fan make: Havells/ Bajaj/ Crompton

Fabrication, supply & fixing of Ceiling fan hook made up of (100 * 100 * 8 mm) size MS plate having 4 no's of 10 mm dia holes and forged and welded with 10 mm thick U-shaped rod in the mid portion and proper filing, sand blasting and rust free paint along with fastners etc., as per the directions of Engineer-In-Charge.

Supply & drawing of 1" size PVC cum metalic flexible hose (Heavy duty) for wires with required all accessories etc., ISI marked

Supply & drawing of 1" size PVC ordinary hose for wires with required all accessories etc., ISI marked

Supplying, fixing, testing and commissioning of the following suitable size modular type PVC box, plate, cover, switch, socket and connections etc.in the wall/surface/recess with wooden planks, including wood / table cutting and making good etc., as required. Make: Legrand-Myrius / Crabtree-Thames

3 module PVC box with modular plate, cover and box in front on surface or in recess or in wooden/metal table, including providing and fixing etc.,

8 module PVC box with modular plate, cover and box in front on surface or in recess or in wooden/metal table, including providing and fixing etc.,

1 No. of 5/6A rating modular switch including connections etc., as required.

1 No. of 3 pin, 5/6A rating modular socket outlet including connections etc., as required.

1 No. of 15/16A rating modular switch including connections etc., as required.

1 No. of 6 pin, 15/16A rating modular socket outlet including connections etc., as required.

Supplying, fixing & termination of suitable size 2 module PVC box with Suitable for RJ45 LAN modular plate and cover in front on surface or in recess or in wooden table, including providing and fixing of 2 no. of RJ 45 LAN socket, connections etc., as required. Make: Legrand-Myrius/ Crabtree-Thames

Supply and drawing following UTP 4 pair twisted CAT - 6 lan cable in existing surface/recess/PVC conduits and including criming, termination, Numbering at both end as required. Make: Polycab/ Molex/ Finolex

Supply and fixing of 40 mm medium class PVC electrical conduit pipe including bends, couplers, end caps, clamps and fastners etc., as required Make: Precision/ Avonplast/ Modi

Supply & fixing of 32*20 mm ISI marked, PVC trunking including end caps, cover joints, bends, couplers, fastners etc., shall be laid in surface/recess including cutting, refinishing the same as required to complete the job. Make: Legrand/ MK