Hindu Religious Institutions And Charitable Endowments Tender

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification.

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling Crushed Stone Sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Supplying and erecting steel shuttering including necessary supports for plain surfaces for reinforced cement concrete works such as grade beams, column footing, plinth beam, staircase steps, pedestals bed blocks cover slab etc., using mild steel B.G 10 sheets of size 90cm X 60cm Stiffened with mild steel angles of size 32mm X 32mm X 3mm for boarding laid over silver oak ( Country wood) joists of size 10cm X 6.5cm spaced at about 90cm centre to centre, supported by casurina props 10cm to 13cm diameter spaced at 75cm centre to centre etc., complete complying with standard specification.

Supplying and erecting steel centering for sides and soffits including supports and strutting up to a height of 3.29 meters for plain surfaces such as RCC slabs, beams TEE or ELL beams, lintels staircases beams etc., with all cross bracings using mild steel B.G. 10 sheets of size 90cm X 60cm stiffeneded with welded mild steel angles of size 25 mm x 25 mm x 3 mm laid over silver oak (Country wood) joists of size 10 cm X 6.5 cm spaced at about 90 cm centre to centre and supported by casurina props of 10 cm to 13 cm diameter spaced at 75 cm centre to center or at suitable intervals etc., complete complying with standard specification in all floors. A.For plane surfaces such as Rcc Roof slab, beams,Lintels,bet blocks,landing slab, portico slab, beams etc.,

For RCC Square column /Rectangular column etc., Complete

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). A. Foundation and Basement

Ground Floor

First Floor

Second Floor

Providing and laying in position, Standardised Concrete Mix M-35 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). A.First Floor

Manufacture, supply, install, profile, stressing and cement grouting all post tensioning tendons including. HT strands to IS 14268-1995, Class II with UTS of 183 KN / 260.4 KN per strand, casting, Barrels, Wedges, and duct. Supply and execution of Post tensioning work must be carried out by a specialist agency, with their own equipments, accessories and skilled manpower as per approved construction drawings. The rate quoted shall be inclusive of cost of strand, ducts, supply, fixing, profiling of tendons, stressing, grouting, complete as shown in the drawing and as per specification . The unit rate for Post tensioning shall also be inclusive of all labour, equipment accessories and technical supervision of the post tension system supplier, who will monitor, insure and certify the correctness of the pre-stressing operations.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). A Foundation and Basement

Ground Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

R.R Masonary in cement mortar1:5(one cement,and five crushed stone sand) for foundation and basement including simultaneously pointing above ground level with the same mortar etc.,complete

Brick work in following Cement Mortar 1:5 ( One cement and five sand ) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction. A. Basement and Foundation

Ground Floor

First Floor

Second Floor

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) A.Ground Floor

First Floor

Plastering with Cement Mortar 1:5 (One cement and five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the concerned officers.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Brick masonry in C.m 1:4 using stock bricks including all varivargams, moulds, sthambams, mukapathrams,koodu, Nasi and all ornamental brick work complete, all pancharams, Agarais, karnakoodus etc., forming core walls of Rajagopuram / Vimanams complete including cost and conveyance of all materials including cement all the labour charges including marking pathies shaping of the bricks, including lifting of all the materials to required heights, curing and all extra for working in heights etc, complete.100 cft

Providing vargapoochu over the core walls of Vimanams/Gopurams, with Cement martor.1:4 complete including shaping the mukhapathram, mahannasi,koodu all arnamental works to proper shape, by embedding broken bricks or shaped/chiselled bricks, rough - plastering with Cement martor.1:4 and finishing with final ornamental plastering and nayam theervai including cost and conveyance of all materials labour therefore, lifting of materials, all woeking in heights curing with water etc, complete - including all extra for folding and including clearing the debris from the vimanams/ Gopurams - Upto 15'0" height

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with Ceramic Tiles of size 300mm x 450mm x 8mm set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and laying of Interlocking Paver Block Stone 80mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc.,

Providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing ornamental M.S Grill of approved design for open court yard grill with doors and window openings etc.., using necessary mild steel flats for inner and outer member which should be fixed an edges including priming coat of best approved quality red oxide primer etc.., complete with standard specification.

Supplying and fixing barbed wire fencing using Barbed Wire - 10 Gauge - Two ply and four pronged (Galvanised) including labour charge for fixing in position with GI binding wire etc.,,

Supplying ,fabrication and fixing of MS angle of size 50x50x6mm for barbed wire fixing post including cost of labour charge ,trasportation and all convenyance with one coat primer

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 132GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and Fixing UPVC (unpoly vinyl choride) Louvered type Ventilators of from the profile the size of outer frame 60 mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free,the profiles are multi chambered sections with wall thick of 2mm.The EPDM rubber ( black colour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers.The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The ventilator should be got approved from the Executive engineer before use on work.

Painting two coats of newly plastered wall surface with ready mixed water based emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing of Teak wood scantling over 2m and below 3m in lenth inlcuding materials and labour charges etc. Complete complying with standard specification.The teak wood scantling should be got approved from the Executive engineer before use on work.

Supplying and fixing of solid core flush shutter with teakply on both side with teakwood lipping alround 35mm thick including cost of materials,labour charges etc.,Complete complying with standard specification.

Supplying and fixing in position F.R.P Door shutter with frame made out of FRP sheets 3mm thick of all size 65mm x 50mm with rebate suitably reinforced using ms angle/ flats, cost of holdfasts and solid core FRP shutter panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc.,of sizes specified by engineers.Complete complying with standard specification.

Supplying and fixing of Flush door shutter using Teak wood frame of size 127mm x 76mm and Door shutters Single leaf in position using 35mm thick Solid Core Flush Shutters with teakply on one side and commercial ply on other side with teak wook lipping alround including cost and labour for fixing the hold fasts and furniture fittings etc.,complete as directed by the departmental officers complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 25mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Drilling of Borewell anywhere in Tamilnadu including transportation from place to another with in Tamilnadu in alluvial soil sedimentary stone of clay and sand stone shale pebbles boulders etc.,By first taking pilot board of 150mm dia and then enlarging to requires dia direct reverse totary mud circulation method including charges for all transport cost of fuel,labour charges bentonite mud and water required for drilling site shown by the departmental officers including construction of mud eniloplese. A.For Borewel

Supplying and Fixing 150mm dia 6kg/cm2 PVC Pipes,Drilling of 150mm dia upto Rock top etc., Complete

Supplying and Fixing UPVC 40x6kg/cm2 pipes including transportation and all conveyance charges etc., Complete

Labour charges for inserting 150mm dia PVC casting pipes assembly (With slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete,suppying and packing the annular space with pebbles of size and quality as approved by the executive engineers of TWAD Board

Supplying and fixing in position the following GI Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The GI specials should be got approved by the Executive Engineer concerned before use on works.) A.'Borecap using M.S.Flat of size 1cm x 3mm and M.S.Sheet on top with bolting arrangements for securing the cap in position (Bore caps with M.S. Couplings need not be made)

Supplying and fixing in position first quality and approved variety of Non return Valve / Wheel Valve/ Check valve/Push valve (Heavy type) with ISI make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications . The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. A.50mm dia UPVC Pipe

32mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying and fixing in position the following UPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of UPVC pipes, jointing the UPVC specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The UPVC specials should be got approved by the Executive EnUPVCneer concerned before use on works.) A.UPVC 50mm dia Elbow

UPVC 50mm dia Union

UPVC 50mm dia Tee

UPVC 50mm dia Bend

UPVC 32mm dia Elbow

UPVC 32mm dia Union

UPVC 32mm dia Tee

UPVC 32mm dia Bend

UPVC 20mm dia Elbow

UPVC 20mm dia Union

UPVC 20mm dia Tee

UPVC 20mm dia Bend

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level etc.,Complete complying with standard specification. 110mm dia PVC pipe A.75 mm dia PVC Pipe

110mm dia PVC pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). A.75mm dia PVC Elbow

75mm dia PVC Tee

PVC 110mm dia Elbow

PVC 110mm dia Tee

PVC 110mm dia Bend

PVC 110mm dia PVC Y with single door

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing in position 20mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC/Fibre glass framed 600x450x5.5mm thick mirror ,shelf type with hard board backing of approved colour fixed with brass screws,rawl plug,etc., Complete complying with standard specification.

Supplying and fixing approved best quality aluminium anodised towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and cp screws etc., Complete complying with standard specification.

Supplying and fixing best approved best quality brass cp tray of size 150x100mm including cost of teak wood plugs , brass screws etc., Complete complying with standard specification.

Supplying and fixing of Health faucet including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5points/Coil) Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (6points/Coil) Higher End

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, with suitable Module GI switch box in flush with wall with 1no 6A one way module switch and 1no 6A 3/2pin module socket with module front plate and making good of the concealed portion with suitable colour for concealed PVC pipe plug point.(8 points / Coil) Higher End.

Supply and fixing of 4’20W SBT LED tubelight fitting with LED bulb complete on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp.

Supply and fixing of 18W LED Square type Recessed fitting with LED (Higher End) on false Ceiling with suitable hanging support from Ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 9W LED lamp

Supply and fixing of 7W / 9W LED for BH point

Supply and fixing of 100W LED Focus / Flood light fitting complete with supports with suitable MS clamps, painting and electrical connections complete.

Supply and fixing of 450mm (18") sweep (Heavy duty) AC exhaust fan complete with necessary wall opening and making of the wall

Supply and fixing of louvers shutters arrangements for 450mm (18") sweep AC Exhaust fan

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making of the wall.

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep AC Exhaust fan.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 65mm dia (21/2") GI pipe (ClassB) of 7metre length with 300mmx300mmx6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to 6A DP MCB switch, 2/4way connector on suitable hylem sheet and Supply and fixing of 2nos of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 2 nos.6A two module 5 pin socket, 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3 nos.6A two module 5 pin socket, 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed box (GI) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed box (GI) in flush with wall with connections. Higher End

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 1.5 TR Split AC (3Star) and 4 KVA stabilizer with MS stand, copper coils of reputed make with required accessories and as directed by the departmental officers.

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection

Supply and fixing of 6A to 32A DP MCB switch in sheet steel enclosure with necessary electrical connection.

Supply and fixing of 63A FP MCB switch in sheet steel enclosure with necessary electrical connection.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 100A 4P MCB Switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Switch as incoming and 9 nos. 6A to 32A SP MCB and 1no 6A to 32A TP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Switch as incoming and 9 nos. 6A to 32A SP MCB and 1no 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 2 of 2.5 sq.mm (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 2 of 4 sq.mm (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 4 of 10 sq.mm (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 4 of 16 sq.mm (101/0.45) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 4 of 25 sq.mm (168/0.45) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and clarnping of 4 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and laying of 4x10 sq.mm PVC armoured LTUG Cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable compeletly with bricks and sand and refulling the earth make good.

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and clamping of 31/2 of 150sqmm PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and laying of 31/2 x 150sqmm PVC armoured LTUG Alu. Cable in a trench to be excavated at a depth of 0.75metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and Clamping of 3-1/2 of 150Sqmm PVC LTUG armoured cable with Angle iron frame work on post or on wall with MS clamps.

Supply and clamping of 3 1/2 x 150sq.mm PVC armoured LTUG Alu. cable with 65mm dia GI pipe on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 31/2 x 150sq.mm armoured LTUG cable with earth connection

Supply and providing end termination of 31/2 x 150sq.mm PVC LTUG armoured cable with necessary Alu. Cable sockets by crimping etc., with electrical connection complete.

Supply, Erection, testing and commissioning of 415V/50HZ 200A cubical panel board with centre switch chamber, cable chamber & the busbar chamber on extreme end with 16 SWG CRCA sheet. 1. 200A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 No 2. 100A TPN switch disconnector fuse unit interior only with HRC fuses double break-2 Nos 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break-6 Nos The busbar chamber shall consist of 1"x ¼" copper flat for 3phases and neutral and interconnection between 250A main switch to main buses. The 1"x ¼" copper flat for interconnection between main buses to 100A and 63A sub switches with Digital Multifunction meter and one set of LED pilot lamps with HRC fuse link for 3phases on a separate chamber. The copper buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules and 2Runs of 1"x 1/8" copper flat on rear side of the panel board for earth buses. Heat shrinkable sleeves shall be provided for busbar with colour code. The panel shall be mounted on MS base channel provided all round at the bottom of the panel inclusive of Fabrication charges, Erection charges and Commissioning and with 1No Metallic danger board with powder coated painting, necessary identification of outgoing loads, bus capacity, cable size etc., with bold letter. (Note: All SDF units shall be of L&T/Siements make)

Supply and fixing of 200A Three phase 4Pole change over switch on suitable angle iron frame work with MS cable entry boxes with connections only.

Supply and fixing of 200A TPN sheet steel double break switch with HRC fuses and neutral on suitable angle Iron frame work with MS cable entry boxes and with earth connection only.

Supply and fixng of TNEB Meter Board suitable for 3 Phases 200A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 200A fuse units (500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete.

Supply and fixing of 3 phase 200A aerial fuse unit for 3Nos 200A fuse units (500A) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron frame work the tapping pole with necessary clamps.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 of No.8 SWG copper wire for earth connection.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps /supports on wall /ground for earth onnection.

Supply, Erection, Testing, Commissioning and Handing over of 1 No 100 KVA Diesel Generator set (Make: Kirloskar/ Ashok Leyland/ Equivalent) of 0.8P.f. Three Phase, 415/420Volts, 50c/s, 1500 RPM as detailed below with 100KVA AMF 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 310 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: Diesel Generator with acoustic enclosure Conforming to CPCB IV+ Norms and BIS Specification 1.Dry type Air cleaner2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter (pre and micro) 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10.24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Muffler 14. Fly Wheel with starter ring, dynamo, standard batteries with cable, flexible exhaust piping. ENGINE INSTRUMENT PANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure gauge, oil temperature gauge, high water temperature gauge and electronic hour meter and RPM indicator SAFETY SYSTEM OF ENGINE The Engine shall trip for the following conditions with visual alarm device. Low lubricating oil pressure, High Water temperature Vee-belt failure and over spee,d Low battery indication The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load.2.ALTERNATOR: Alternator capacity of 100 KVA/100 KW, AC 3 phase, 50 HZ, 415/420V, 0.8 P.F. 4 Wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate 3. AMF Control Panel : The AMF control panel (Cubicle) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front doors with enamel painted and incorporating the following with suitable provision for connecting incoming and outgoing leads having been made on the control panel. 1No AC Ammeter 3Nos Current transformers with suitable ratio 1No Ammeter Selector switch 1No Voltmeter5.1No Voltmeter Selector switch 6. 1No Frequency meter 7.1No KWH meter 8.1No Power factor Meter 9.1No KW meter 10.Battery charging set comprising of the following for charging the battery from mains. a.Transformer/Rectifier b.DC Ammeter c.Charging rate selector switch d.DC Voltmeter e.Circuit breaker f.Voltage Regulator g.ON/OFF Switch Note: This will be in addition to the battery charging alternator fitted to the engine1Set Air break contactor with auxiliary neutral contactor for main supply, 1 Set Low voltage HRC fuse for the short circuit protection of the main supply,1 Set Alternator contactor with auxiliary neutral contactor,1 Set three pole bimetal release for over load protection of alternator.1 Set low voltage HRC fuse for the short circuit protection of the alternator.1 Set DC Control relays incorporating engine start stop and failure to start/lockout 1Set Selector switch auto /manual 18.1No Push button“Start’ 19.1No Push button “Stop’20.1No Push button “Reset’21.1No Signal lamp for indicating load on mains22.1No Signal lamp for indicating load on set 23.1No Signal lamp for indicating set fails to start24.1No Signal lamp for indicating ‘Set running’25. 1No Signal lamp for indicating ‘Battery charger ON’26. 1Set Pilot lamps of 3Nos27. MCCB of 250A capacity with magnetic thermal over lead release, instant start circuit trip and under voltage release switch. 28.Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duty colour coded with head shrinkable PVC sleeves.29. 1No Mains Voltage monitor30. Hooter/Audio Alarm for indicating set fails to start and for DG O/L31. 1 Set Timers32. Audio and visual indication arrangements for:a.Low lubricating Oil pressure. High water temperature c.Over speed33. 1No Earth fault relay34. Isolator to Isolate the neutral. Note:1.The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements.2.The engine should trip for the followinga.Low lubricating Oil pressure b.High water temperature c.Over speed4.ACOUSTIC ENCLOSURE:Acoustic enclosure shall be powder coated and fabricated of16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1 mm Powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt. distance shall be less than 75 DBA average or as per CPCB norms.Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/Structures are used in canopies so as to give sturdiness and to reduce the vibration of the DG sets if any.World class Cooling package:Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature. No grouting required on the ground, only a level surface capable of withstanding the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set.The Gen set frame shall also be provided with hooks for unloading.Temperature rise inside the canopy:Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 57 deg centigrade. 5.FUELTANk 300 liters Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. BASE FRAME The base should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be provision for the mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading, transportation charges.7. Battery:2 Nos 12V 180 AHR Battery. (DATA-X)1 Set DC Control relays incorporating engine start stop and failure to start/lockout 1Set Selector switch auto /manual 18.1No Push button“Start’ 19.1No Push button “Stop’20.1No Push button “Reset’21.1No Signal lamp for indicating load on mains22.1No Signal lamp for indicating load on set 23.1No Signal lamp for indicating set fails to start24.1No Signal lamp for indicating ‘Set running’25. 1No Signal lamp for indicating ‘Battery charger ON’26. 1Set Pilot lamps of 3Nos27. MCCB of 250A capacity with magnetic thermal over lead release, instant start circuit trip and under voltage release switch. 28.Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duty colour coded with head shrinkable PVC sleeves.29. 1No Mains Voltage monitor30. Hooter/Audio Alarm for indicating set fails to start and for DG O/L31. 1 Set Timers32. Audio and visual indication arrangements for:a.Low lubricating Oil pressure. High water temperature c.Over speed33. 1No Earth fault relay34. Isolator to Isolate the neutral Note:1.The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements.2.The engine should trip for the followinga.Low lubricating Oil pressure b.High water temperature c.Over speed4.ACOUSTIC ENCLOSURE:Acoustic enclosure shall be powder coated and fabricated of16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1 mm Powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt. distance shall be less than 75 DBA average or as per CPCB norms.Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/Structures are used in canopies so as to give sturdiness and to reduce the vibration of the DG sets if any.World class Cooling package:Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature. No grouting required on the ground, only a level surface capable of withstanding the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set.The Gen set frame shall also be provided with hooks for unloading.Temperature rise inside the canopy:Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 57 deg centigrade. 5.FUELTANk 300 liters Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. BASE FRAME The base should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be provision for the mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading, transportation charges.7. Battery:2 Nos 12V 180 AHR Battery.

Design, engineering, supply, erection, testing, commissioning and handling over of the 13 persons capacity (884 kg) Bed cum passenger lift, gearless with machine room as per the following technical specification: (SOR-M-2365)With Stainless Steel Panel ,Disabled Friendly Microprocessor Based Controller VVVF Drive ,Fire Rated Door and ARD TECHNICAL SPECIFICATIONS:-1) Location: Marriage mandapam, Kothapulli2) No. of lifts / Type of Lift: One / SUKRANTI-Passenger3) Capacity of lift: 13 persons capacity (884 Kgs) Bed cum passenger lift4) Speed: 1.5 Mtr Per Second.5) Type of Drive: Microprocessor based Variable Voltage Variable frequency (V3F) drive with enhanced ride comfort and levelling functions.6) Position of Machinary: Directly above the lift well - GEARLESS7) No of floors: G+2 (3 landings)8) Total travel 12.96 Mtrs8) Total travel 12.96 Mtrs9) Leveling accuracy:- High level accuracy with smooth and jerk free stopping.10) Design of car: Stainless Steel hairline finish combination car body with SS finish ceiling (sleek medium circular LED lights, regular circular fans SS Handrail & PVC flooring.11) No. of landing entrance : Basement +2floors (3 landings)11) No. of landing entrance : Basement +2floors (3 landings)12) No. & position of car entrance : one in front only.13) Size of lift well: 2500 mm x 1900mm (Width x depth)14) Lift Car inside size: 2000mm x 1100mm x 2200mm (width x depth x height)15) Lift pit & head room: 1800mm deep, Head room 5000 mm height.16) Car clear opening: 900mm x 2000mm (width x height) Lintel - 2200mm16) Car clear opening: 900mm x 2000mm (width x height) Lintel - 2200mm17) Landing entrance door: Power operated V3F door, Centre opening sliding door - stainless steel (1.5 mm) - hairline finish.18) Landing entrance frame: stainless steel - hairline finish.19) Control:- Microprocessor based Simplex selective collective control with / without attendant.20) Indication: Dot Matrix LED Direction & Position Indicators in car & landings. Puch button;_orange LED illumination.21) Emergency Alarm Bell: Battery operated alarm bell to be provided with automatic charging device.22) Emergency light: Battery operated light to be provided with automatic charging device.23) Fireman's switch : To be provided at ground floor.24) Minor builder works: To be provided by lift contractor.25) Scaffolding: To be provided by lift contractor.26) Stainless steel Sill angles and facia plates: To be provided by lift contractor.27) Steel for lift machinary :- To be provided by the lift contractor.28) Servicing and maintenance: Lift contractor should provide free comprehensive servicing and maintenance during the guarantee period.29) Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc. Complete with all accessories.30) Provision if Intercom with phone:- To be provided by the lift contractor31) Lift license: Preparation of drawings, lift contractor should do payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act.32) Floor announciator with music: To be provided in the car33) Special features:(a) Battery Operated Emergency Light and Alarm Bell(b) Call Register Signal And Vf Door Operator(c) Automatic Rescue Device.(d) Stainless Steel Button with S.S. Cover.(e) Dot Matrix Led D & P Indicators in Car & Landings - Orange Colour.(f) Floor Annunciator with Music.(g) Firemans Switch(h) False Ceiling in Car.(i) Fire Rating of Landing Doors-One Hour(j) Infra Red Door Screen(k) Overload warning Indicator(l) Laminated Mirror At Rear Side.(m) Scaffolding(n) Two way Intercom with press & speak in Cop(o) Provision for EBABX(p) Free Service for One Year(q) Pit Ladder(r) Ss Handrail(s) Lift License(t) Minor Builders Work(u) Provision for Cctv Camera - Ip (Cat6 Flat Travelling Cable)34) Over speed governor, phase failure and phase reversal relay, alarm bell, T Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression spring etc.35) Guarantee: Gurantee for the materials and lift firm should offer workmanship of equipments complete for a period of not less than one year.

Sub Total

GST @ 18%