Hindu Religious Institutions And Charitable Endowments Tender

Plain Cement Concrete 1 : 5 :10 ( one part of cement, five parts of sand and ten parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement.

Supplying and Filling Gravel Supplying and filling in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Construction of Granular sub-base of 125mm compacted thickness by providing laying, spreading and compacting of Close graded Material conforming to Grading V of Table 400- 1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading, maintenance of diversion road, loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORTH technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work.

Construction of Wet Mix Macadam 250mm compacted thickness in two layers by providing , laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying the physical paraeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mied material to work site and laid in sensor pavers to the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer-In-Charge of work.

Refilling the approved good quality earth in plinths, area development etc. wherever specified in layers of not exceeding 200 mm thick., with available earth at site.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. A)For Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

For Vertical surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). A)Foundation & Basement

Ground Floor:-

First Floor

Second Floor

Terrace Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(Contractor has to make his own arrangements for the supply of steel and binding wire)

Brickwork in Cement Mortar 1:5(One cement and five sand) using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" in foundation, basement and superstructure including curing etc. complete complying with standard specification. A)Basement:-

Brickwork in Cement Mortar 1:6(One cement and six sand) using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" in foundation, basement and superstructure including curing etc. complete complying with standard specification. A) Ground Floor:-

First Floor

Second Floor

Terrace Floor

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Bricks of size 9" x 41/2" x 3" in Cement Mortar 1:3 (One Cement and Three Sand) and both side plastering with CM 1:5 12mm thick using hoop iron reinforcement if found necessary including curing etc.complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately). A)Ground Floor:-

First Floor

Second Floor

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 for Internal walls & External walls (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification

Dadooing walls with best approved quality, white / colour glazed tiles of size 450x300x8mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 600 x 600 x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/Sqm laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge. (Including Skirting work)

Flooring with following ceramic tiles of size Joint Free Rectified Ceramic tile of Size- 305 x 305 x 8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and Paving the Paver Block flooring using Rubber mould paver block (Colour) of standard size over the sand filling of 83mm thick, including laying Compacting with power machine including loading transportation and colour pigments of paver blocks, including cost and conveyance of all materials labour etc complete with standard specification.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Toilet Sunken using broken brick jelly 20 mm gauge The proportion of broken brick jelly to slaked lime being 1:3:6 (1part cement,3 part fine aggregate & 6 part broken brick jelly), well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers. A)First Floor

Second Floor

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed.Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Paving the Top of roof with Solar refelective tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

UPVC Window :Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm125GSMand 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates ashandle. The corners and joints should be welded andcleaned. Radiations free pin headed plain or browncolour glass 4mm thick should be provided to theshutter and it should not allow leakage of water evenat most ranging storms and should have key lockableaction, security protective hinges, strong lockingsystems and as per size for arresting noise and energyloss. The connecting mechanism between sash andouter frame that enables opening of the window. Thewindow should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (blackcolour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Solid PVC door shutters Toilet door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.

Door Frame: Supplying and fixing first quality teak wood frames for doors, windows, ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc. complete in all floors. A)Teak wood Scantings up to 2M

Teak wood Scantings over 2M and below 3M

Double leaf full glass door:To be made out of 12mm thk Toughened glass with etching as per design .The glass with etching has to be fixed. with all side and Top rails of size 1 1/4" x 5" and the Bottom rail of size 1 1/2" x 10".The rails to be made out of best quality beach wood.The door shall have 18" long S/S handle and also 2 nos of double action floor spring of specified make. The etching in glass pattern to be followed strictly as per instructions of the Architect or following the drawing attached.NB: Size of the door may slightly vary as per site conditions for matching the elevation of the fixed glazing. All exposed edges of the glass to be machine polished.dorma/Eqivalent patch fitting and locking arrangement is to be used for fixing the glass.

Supply & Fixing of Single Leaf Solid core Flush shutters with Teak ply on both side with teak wook lipping alround 35 mm thick, with necessary adhesives and CP screws complying with standard specification.The cost is inclusive of 1 No Lock arrangement, handel, tower bolt ,approved equivalent make SS ball bearing hinges of quivalent make of aproved make, 2 no floor mounted SS door stoper ect.complete as per drawing.

Supply & Fixing of 35mm thk.Double leaf high density interior grade marine plywood shutters pasted both sides 1.5mm thk.laminate approved design with 35x12mm T.W.lipping on all edges with necessary adhesives and CP screws complying with standard specification.The cost is inclusive of 1 no Lock arrangemen,handel,tower bolt ,approved equivalent make SS ball bearing hinges of quivalent make of aproved make,2 no floor mounted SS door stoper ect.complete as per drawing. ake:Kutty,Sharon,Trojan. Accessories Make:Dorma, Godrej.

Supplying, fabricating and fixing in position of Alumi.Anod.using 5.5 mm thick frosted glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best track arrangement on top, Aluminium Handles on both sides,stopper bush on top,tower bolt,Locks and glass including all materials,Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with mattfinish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.All the materials should be got approved by the Engineer - In -charge before fixing as directed.

Supplying and fixing in position of Gyp board false ceiling made with 10mm thick Gyp board and standard size GI channels at a spacing of not more than 1200mm c/c, on longitudinal directions and 600mm c/c on lateral directions with necessary fasteners for fixing the frames. The Gyp board sheet shall be fixed in the frames with necessary star screws and to be used for joining the frames. The rate is including cost and conveyance of all materials complying with standard specification.

Fixed Glazing: Designing the semi unitised structural glazing system with open groove joint as per designed intent,preparation of shop drawings for apprival, supply, fabricate,erect as per approved shop drawings at all floor levels and floor heigth including conducting field test as per the test criteria set out in the particular specification (metholodgy should be got approved by the Dept.officials.) Design the framing system(i.e. male & female frame) to support vision panels either with glass or aluminium composite panel, openable ,window panels on a continuous framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated/monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm.glazing of panels shall be done only at factory at the controlled atmosphere.

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x18mm.Accessories: Brackets made of CRCA powder coated /electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used.The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames.Glass: 5mm reflective Saint Gobain OR equivalent.

Providing and fixing welded M.S. grills to the window openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Engineer-in-charge.

Paving the floor with best approved quality Natural flammed finish granite for flooring/ steps & Landing of 18 / 20mm thick of with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of all materils, Labour charges for cutting, bending, welding, grinding, polishing, Transportation, electrical charges, etc. complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing Zinc chromite priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with weather proof ready mixed Exterior Emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supply & Fixing of two in one CP Health Faucet of the closet mounting type with hose connected two way BIB COCK complete fittings. (Make: Parryware or equivalent)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying & fixing of Long body bibcock SS Heavy Duty Long Body Tap 15mm with brackets including fixing over Wall tile dado complete.(Make: Parryware or equivalent)

Supplying & fixing of CP Angle Cock Tap stopcock with connecting hose and wall flange. (Make: Parryware or equivalent)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) .

Supplying & fixing of CP stopcock with connecting hose and wall flange. (Make: Parryware or equivalent)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level A)50mm dia.

75mm dia.

110mm dia.

Supplying and fixing in position PVC nahini /Floor Trap with PVC Grating type of size 100x75/75x50 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1:2:5(One lime two sand and five aggregate) brick jelly 40mm and finishing with CM 1:3(One cement and three sand)wherever found necessary and making good to the original condition and giving connections to the PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer.

Supply and fixing in position best quality PVC IS 4985 - CLASS-II - 4 Kg/Sqcm -Rain water pipes of various size having ISI mark and providing leak proof joints with such as Bend, Tee Junction, door etc.,of approved qualityincluding fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, wherever necessary and making chipping good to the original condition, complying with standard specification etc., complete. A)75mm dia.

110mm dia.

Supplying and fixing in position of the following dia PVC rain water gratings for rain water pipes ,of approved quality and variety of various size confirming to ISS and including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer A)75mm x 50mm

100mm x 75mm

Supplying and fixing in position of the following dia PVC specials such as PVC vent Cowl etc.,of approved quality and variety of various size confirming to ISS amend providing leak proof joint etc., including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer A) 75mm dia

110mm dia

Supply and fixing in position best quality PVC IS 4985 - CLASS- III - 6 Kg/Sqcm -Soil/ waste pipes of various size with approved quality and variety of various size confirming having ISI mark and providing leak proof joints including erection of below ground with excavation and refilling etc., and making connection to Manholes / Gully trap, wherever necessary and making chipping good portion to the original condition, complying with standard specification etc.,complete. A)75mm dia.

110mm dia.

160mm dia.

Supply, laying and erction of glazed stone ware gully trap (100 x 75 mm) with 100 mm dia, outlet including embedding trap in cement concrete 1:3:6 and constructing chamber of size 300 x 300 mm inside clear in brick masonry 230 mm thick, plaster with water proof cement mortar (1:3) 15 mm thick on both internal and external surfaces inside finished with floating coat of neat cement. The work including excavation to required depth of gully trap and refilling and making good in the surface with Providing and fixing SFRC frame and cover 400 x 400 mm (clear opening) complete complying with std. specification.

Supplying and Erection and construction of sewer chambers of required internal dimensions 450x450 upto 0.6 mtr.depth with 230mm brick masonry in C.M.1:5 thk of masonry over bed of 1:2:4 R.C.C. 200 mm thk bove 100 mm thk P.C.C.1;3:6 Cement concrete foundations over sand bed of 100mm thk channelling in 1;2:4 cement concrete, plastering in 1:3 cement mortar for internal and external surface finished with floating coat of neat cement, the work including excavation for required depth of gully trap and refilling and making good in the surface with SFRC cover and frame 450x450mm (clear opening)complete complying with standard specifications etc.,

Construction of rain water recharge well of 1200mm dia and depth upto 1500mm, in addition 110 dia special blue slotted pipe for bore well.pipe should be laid from bottom of ring well centre to below 1500mm as shown in the drawings, including all types of excavation,occur for pipe, filling of rain water harvesting materials with construction of R.C.C. ring and top 100mm RCC SLAB WITH 450X450mm perforated SFRC manhole and 230mm brick wall in 2'height with below 300mm lengthx100mm thk P.C.C. as per the structural filling the filter media as per drawing.

Providing, supplying & laying of Unplasticized Polyvinyl Chloride (UPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour, transportation,tools & tackles all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer. A)20 mm nominal (OD) pipes

25 mm nominal (OD) pipes

Providing, supplying & laying of UPVC (UPVC-SDR-13.5) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications, Exposed work including chase cutting, bracket fixing)complete complying with standard specification and as directed by the Departmental Officer. A)25mm nominal(OD) pipes

Providing, supplying & laying of Chlorinated Poly Vinyl Chloride (UPVC) Pipes conforming to IS 15778 having thermal stability cold Metro water with brass and UPVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer. A)40mm PVC pipes

Providing, supplying & laying of Gunmetal type NRV - pressure rating less tahn 16 Kg/Sqcm and IS778 with 2 Nos of MTA with jointing material like shellac, thread including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles all complete as per as per specifications, complete complying with standard specification and as directed by the Departmental Officer. A)32 DIA

40 DIA

Supplying and erection of horizontal shaft centrifugal mono block power pump set of single phase 2.00 H.P of best approved quality and make with ISI mark on suitable pedastal with foundation bolt and nut including labour supplying and fixing of starter and main switch suitable for 2.00 H.P pumpset on suitable angle iron frame work with necessary labour including panel board, supply and run off 4 of 10 Sq,mm, in P V C pipe with 14 SWG TC wire including fixing of suction pipe and foot valve up to a maximum depth of 7m and delivery pipes upto the exterior wall of pump room etc., complete and operating the pumps on trial run for 3 days. (The make and quality of pump set to be got approved by the Executive Engineer before use on works.) (TWAD- Pa no:103 Sl.no:45)150mx 40m

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End (Data A)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End.) (Data B)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC pipe 2 way / Stair case Light point Higher End (Data C)

Supply and fixing of 40W 4’ LED IP40 and IK02. BN100C LED 40 Fitting with WW LED (Philips) complete on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting. (Data D)

Supply and fixing of 40W 4’ LED IP40 and IK02. BN100C LED 40 Fitting with LED (Philips) fittting complete with with conduit pipe suspension from ceiling with PVC unsheathed copper leads from terminals to the fitting with fluorescent Tubes. (Data E)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 526)

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD 549)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall (SD 115)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch (SD 105)

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 535)

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End (Set plug) (SD 466)

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (SD 512)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD 140)

Supply and fixing of 1.5 TR Split AC with 4 KVA stabilizer with copper coils 5 star rated of reputed make with required accessories and as directed by the departmental officers. (Data F)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (SD 414)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 613)

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P RCCB as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data G)

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 63)

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.(SD 424)

Supply, Erection, testing and commissioning of 250 A capacity dust and vermin proof horizontal type cubical panel board made up of 16 SWG CRCA Sheet with supply and fixing of the following interior switches with HRC fuse links arranged horizontally with horizontal busbar chamber and cable chambers. 1. 250A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 No. 2. 32A TPN switch disconnector fuse unit interior only with HRC fuses double break-2 No. 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break-11 Nos. The busbar chamber shall consist of 4 Nos 33mm x 6mm copper flat for phases and neutral and interconnection between incoming switch and buses. The 38mm x 6mm copper flat for interconnection between 11 Nos 63A TPN switches and 2 nos 32A TPN switch to buses. 38mm x 6mm copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for double earth connection for all incoming and outgoing switches are to be provided in this panel. The panel shall have powder coated painting of approved colours, approved by the department officers. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a Masonary pedestal to be constructed with suitable foundation with bolts and nuts such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level. (note: All SDF unit shall be of L&T / Siemens make). (Data H)

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 751)

Supply and clamping of 3½ x 120 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 227)

Supply and fixing of brass cable gland for 3½ x 120 sqmm PVC armoured LTUG cable with earth connection. (SD 191)

Supply anf fixing of 9W LED Bulk head (DATA - I)

Supply and providing cable end termination of 3½ x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 240)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 233)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 458)

Design, engineering, supply, erection, testing, commissioning and handling over of the 8 persons capacity (544kg) passenger lift, gearless with machine room as per the following technical specification: TECHNICAL SPECIFICATIONS- 1)Location: S. No.Oddanchatram for women's Arts College,2) No. of lifts / Type of Lift: One / SUKRANTI- passanger,3) Capacity of lift: 8 persons capacity (544 Kgs) passenger lift,4) Speed: 1.00 Mtr Per Second.,5)Type of Drive, Microprocessor based VariableVoltage Variable frequency (V3F) drive with enhanced ride comfort and levelling functions,6) Position of Machinary. Directly above the lift well Gearless 7) No of floors: Ground Floor+ 3 Floors ( 4 landing ),8) Total travel: 15.96 Mtrs 9) Leveling accuracy- High level accuracy with smooth and jerk free stopping 10) Design of car: Stainless Steel hairline finish car body with SS finish ceiling (sleek medium circular LED lights, regular circular fans SS Handrail & PVC flooring 11) No. of landing entrance Ground Floor+ 3Floors (4 landings) 12) No & position of car entrance one in front only,13) Size of lift well: 1900 mm x 1900mm (width xdepth) ,14) Lift Car inside size: 1300mm x 1100mm x 2200mm (width x depth x height),15) Lift pit & head room: 1600mm deep, Head room 4800 mm height 16) Car clear opening: 800mm x 2000mm (width xheight) Lintel-2200mm 17) Landing entrance door: Power operated V3F door, Centre opening sliding door - stainless steel(1.5 mm)-hairline finish.,18) Landing entrance frame: stainless steel hairline finish.,19) Control- Microprocessor based Simplex selective collective control with/without attendant , 20 ) Indication: Dot Matrix LED Direction & Position Indicators in car & landings. button orange LED illumination.,21)bell to be provided with automatic charging device.,22) Emergency light: Battery operated light to be provided with automatic charging device.,23) Fireman's switch: To be provided at ground floor 24) Minor builder works: To be provided by lift contractor.,25) Scaffolding To be provided by lift contractor,26) Stainless steel Sill angles and facia plates: To be provided by lift contractor., 27) Steel for lift machinary To be provided by the lift contractor. 28) Servicing and maintenance: Lift contractor should provide free comprehensive servicing and maintenance during the guarantee period. 29) Automatic Rescue Device To facilitate the landing of the lift to the nearest floor at the time of power failure This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc Complete with all accessories. 30) Provision if Intercom with phone. To be provided by the lift contractor 31) Lift license Preparation of drawings, lift contractor should do payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act. 32) Floor announciator with music. To be provided in the car33) Special features: (a) Battery Operated Emergency Light and Alarm (b) Call Register Signal And Vf Door Operator (c) Automatic Rescue Device. (d) Stainless Steel Button with S S. Cover. (e) Dot Matrix Led D & P Indicators in Car & Landings-Orange Colour. (1) Floor Annunciator with Music (g) Firemans Switch (h) False Ceiling in Car (1)Fire Rating of Landing Doors-One Hour (i) Infra Red Door Screen (k) Overload warning Indicator (1) Laminated Mirror At Rear Side. (m) Scaffolding (n) Two way Intercom with press & speak in Cop o)Provision for Fpabx (p) Free Service for One Year (q) Pit Ladder (r) Ss Handrail (s) Lift License (t) Minor Builders Work (u) Provision for Cctv Camera lp (Cat6 Flat Travelling Cable) 34) Over speed governor, phase failure and phase reversal relay, alarm bell, T Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression spring etc. 35) Guarantee: Gurantee for the materials and lift firm should offer workmanship of equipments complete for a period of not less than one year.

Supply and laying of 3½x25 sq mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 meter putting 0.15 meter layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (For Lift) [SD 204]

Supply and clamping of 3½ x 25 sqmm PVC armoured LTUG cable on wall with earth connection (For Lift) [SD 222]

Supply and providing cable end termination of 3½ X 25 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete[SD 235]

Supply and fixing of brass cable gland for 4 x 25 sqmm PVC armoured LTUG cable withearth connection [SD 185]

Supply and run of 25mmx3mm copper flat with with screws on wall / floor for earth connection. Lift earth. (Lift) [SD 76]

Supply and fixing of 4 way vertical DB neutral MCB distribution board in sheet steel enclosure double door of double door type with metal door with IP43 protection with 63 A 4 pole MCB isolator as incoming and 2 Nos. 32A TP MCB (Hager) and 6 Nos 32A SP MCB's and outgoing on Angleiron frame with earth connection. The MCBDB and MCB's should be with the ISI mark (like Hager / Legrand make) (Lift) (DATA F)

Supply, erection, testing and commissioning of 62.5 KVA Diesel Silent Generator set 0.8 PF 3 Ph, 415V, 50 HZ as Details below.A.Engine: Water cooled Diesel Engine type suitable for generating application with a Shaft output of suitable capacity of 83 BHP at 1500 RPM under NTP conditions. As per the BSS 5414/ISO 3046 The Engine Shall comprise the following standard Fittings.(Kirloskar/Cummins/Equivalent) B.Alternator: Capacity of 62.5/50 kw/36 kw,0.8 PF self exited, self regulated design to run a 1500 RPM under NTP condition confirming to BS 5000 /IS13364(part II) 1992 to be coupled directly to the Diesel Engine and Test Certificate. (Kirloskar/Stamford/Equivalent) C.Battery: 1No.12V 88/100 AH Battery with copper leads and terminals, Battery Make EXIDE/AMCO/AMARON I.Acoustic Enclosure: supply of acoustic Enclosure for 62.5 KVA Diesel Generator Set. The Acoustic enclosure is made of 1.6/2 mm thick CRCA sheets in munsel Green shade and s Structural Sheet metal base frame Painted in Black. The walls of the enclosure are insulated with the retardant foam so as to comply with the 75 DBA at mtr sound levels specified by Ministry of enforcement.The enclosure should be completed with 1. Arrangement for power cable for connection. 2. Residential exhaust silencer, with flexible base arrangements. 3. Suction louvers. 4. Discharge Louvers. 5. Openable and lockable doors on both sides with air tight Neoprene rubber gasket. 6.Lifting arrangements. 7.Interior lighting arrangements J. Erection, Testing and Commissioning of the genset comprising the following:1. Providing suitable concrete foundation with plain cement concrete 1:2:4 with sand cushion all around and alternator with acoustic enclosure. 2. Erection of generator set complete with acoustic enclosure, fuel tank, engine control Panel, standard control Panel, base frame complete on the above foundation and lifting arrangements.3. First charging of lub oil and first charging of Battery (SD)

Sub Total

GST @ 18%