Hindu Religious Institutions And Charitable Endowments Tender

Providing polymer coating (water proof coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust,foregin,matters lose materials or any other deposits of contamination by rubbing with wire brush. slurry:dry blend and polymer liguid blend shall be mixed into the desired ratio as per recommendation of the supplier,the mix shall be stirred thoroughly untill no bubbles remain in the mix. any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet clenaed surface,after drying,second coat shall be applied on the first coat as directed by the departmental officers etc.the rate inclusive of cost of materials and labour charges etc,complete.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Flooring with Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes 300mm x450mm x 8mm set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality Double change Vetrified ( Such as Morbonite) Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Plastering the surface of wall with cement mortar 1:3 one( cement and three sand) 20mm thick in all floors including clean removal of cement plaster etc complete complying with standard specification and as driected by the departmental officers

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Painting two coats of old plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colourincluding thorough scrapping, clean removal of dirt, and including full paris touch up putty, wherever required etc., complete complying with standard specification.

Painting old wood work with two coats of synthetic enamel ready mixed paint of approved quality and colour coat in all floors including etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Solid core Flush shutters with Teak ply on one side and commercial ply on other side with teak wook lipping alround 35 mm thick including labour charges,materials,tranportation,etc,complete.

Supplying and fixing of Plain Glass - 4mm thick including cost of materials ,labour charges,transportation etc,complete.

Supplying and fixing best approved best quality wash basin nylon wast hose 0.75m length including cost materials.labour charges etc., complete complying with standard specifications. (The nylon hose should be got approved by Executive Engineer before use on works).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick and 1200x600mm mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) 600mm x 450mm wash basin mirror

Special Type Mirror of size 1000 x 780mm

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Cleaning the wall tiles with acid by through scraping and clean removal of dirts in the wall with complete complying with standard specification etc,complete.

Supplying and fitting of furniture fittings aldrop,tower bolt,handle,hinges including cost of materials,labour charges etc complete(Brass). Brass Ornamental Handles 200mm

Brass Hinges 125mm x 30mm

Brass Aldrops 250mm long and 16mm dia

Brass Tower Bolts 200mm long and 12mm dia

Brass Tower Bolts 150mm long and 12mm dia

Brass door stopper

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal ) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying, fabricating and fixing inposition Aluminium anodised natural colour matt finish louvered ventilator size 1200mm x 600 mmof with outer frame section with 62x38x2mm at 1.174 kg/m and the louvered with moving arrangements made with aluminium channel of size 60x30x4mm @ 1.274 kg/m ALuminium clips 19.05x17.27/ 11.05x0.075mm @ 0.169kg/m with necessary 4mm thick plain glass panel for louvers including cost of all materials, labour and power required for fabrications, chipping dismantling making holes in RCC, masonry and made good to the original condition after fixing etc., complete. The Aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of notless than 15 Microns,etc., complete.

Supplying and fixing in position best quality PVC soil / waste pipes of 110mm dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). 110mm Dia 6kg/sqcm pvc pipe

Bath& washbasin waste pipe

Supplying and fixing in position PVC specials of the 110mm dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). PVC Elbow 110mm dia

PVC Tee 110mm dia

110MM X 75MM DIA Reducer

PVC door Y 110mm dia

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Sub Total

GST @ 18%