Hindu Religious Institutions And Charitable Endowments Tender

Supplying and filling in foundation and basement with Quarry rubbish in layers of not more than 15cm thick well rammed watered and consolidated etc.

Refilling basement with excavated earth in layers of not more than 15cm thick well rammed, watered and consolidated etc., complete as per standard specification.

Providing form work for Centering and erecting steel centering including necessary supports for plane surfaces in foundation and basement for reinforced cement concrete works such as column footing plinth beam grade beam staircase step, bed block etc.,which require outer normal strutting using MS Sheet of size 90cmx60cm BG 10 gauge of stiffened and welded with mild steel angles of size 90cmx60cm BG 10 gauge of stiffened and welded with mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by the casurina props of 10cm to 13cm dia spaced at 75cm centre to centre at suitable intervals etc.,complete complying with std specification (The Payment for centering shall be made outer after the concrete is laid)

For column footing plinth beam staircase steps, piers raft beam raft slab etc.,

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Brick work in cement mortar 1:6 using Second Class Ground Moulded Chamber Burnt Bricks 9" x 4 3/8" x 2 3/4"including curing etc., complete complying with standard specification and as directed by the department officers.(Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

Foundation and basement

Ground floor

FIRST floor

Providing and laying in position, standardised concrete Mix M20 grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement content of 325 Kg/m3 and maximum water cement ratio of 0.55 including admixyure (Plasticiser / super plasticiser ) in recommended proportions as per : 9103 to accelerate retard setting of concrete, improve workability without impairing strength and durability with about (5Cum) 7730kg. og 0mm machine crushed stone jelly and with about (3.3cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly with about 4.79Cu.m. )7670kg. of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying , vabricating with mechical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slab where ever necessary without claiming extra ,etc., complete.complying with standarde specification and as directed by departmental officers.The coarse and fine aggregates to be used should compling with the requirements of IS Standards. ( No separete payment will be made by the department for excess usage of materials)

Foundation and basement

Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Plastering with Cement Mortar 1:5 (One cement and Five CS sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three CS Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Distembering the walls two coats with best oil bound distember of approved quality (to be approved by the Executive Engineer before use on works) overone coat of primer for newly platered wall including preparation of surface and finishing neatly including cost of all materials brushes scaffolding charges etc., complete complying with std specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no.

Manufacturing, Supplying and Fixing in position of M.S steel window with following specifications. The outer frame of window made out "Z" section (F7D) of size 33x25x3mm at 1.419 Kg/m and mullion of "J" section (F4B) of size 45x25x3mm at 2.28 Kg/m. Shutter made out of (F7D) section of size 33x22x3mm at 1.419 Kg/m. Each openable shutter should not be exceeded a width 600mm to enable separate operations and easy maintenance. 2Nos. of sturdy hinges and one number of handle cum latch of special type make with 18x5 MS flat are revetted to the shutters of an appropriate height in each window shutter. Suitable opening is left for its easy operation. A stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. Each shutter having an adjustable window stay made out of 18mmx5mm at 0.70 kg/m MS flat of length 320mm with free adjustable positions. A matching peg is provided in the outer frame of the window, at suitable place, 4Nos of holdfasts of 200mm length MS angle 40x40x6mm the ends are welded to the outer frame of the window, 18 mmx 5 mm at 0.70 kg/m MS flat is welded to the shutter at two places, equal distance from each other from top and bottom of the shutter. 18 gauge cold rolled sheet of superior quality is laid as panel in the shutter frames and welded intact. Stiffeners with 18x5mm at 0.70 kg/m MS flat of suitable length welded diagonally to all four corners of each openable shutter to hold the CR sheet in position firmly. MS square bars of 12mm size is welded to the inner face of the window at equal intervals not exceeding 100mm edge to edge between them. All members are painted with one coat of anticorrosive red oxide primer as directed by the departmental officers. All sections used should confirm to IS 7542 / 1990. The rate includes cost of all materials, labour charges, transportation to taxes and other incidental charges etc. complete.

TWO LEAVES

THREE LEAVES

Supplying and Fixing M.S grill to opening corridor sides, ladder Entrance gate and Name board angles etc., Using necessary M.S flat for inner members and outer members which should be fixed to window members frames as directed by departmental officers inclusive of cost of providing one coat of best quality red oxide primer. -The design of M.S. grill should be got approved from departmental officers before use on works.-

Paving the floor with Pre-polished anti-skid step tiles (Required shape and design) of 10 mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Painting new iron works with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., but excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officer. (The make quality and colour of paint should be got approved by the Engineer before use on work).

Supplying and fixing in position best approved of ISI quality of 110mm diameters of PVC rain water down fall pipes having a working pressure of 4 kg / sq.cm including cost of necessary PVC shoe, PVC bend, C.I. gratings of required diameter and special clamps, brass screws, nails etc., and fixing of cast iron gratings at juction of parapet and the RCC roof slab including finishing, neatly etc., complete. The rate shall be inclusive of cost of removable iron grating. The PVC pipe shall be fixed in wall with special type of clamps. Special type "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0M pipe length complying with standard specification.

Cement concrete 1;3:6 (one cement tree sand and six oars aggregate) using 40mm 12mm (40,20,120 gage downgraded hard broken stone jelly for dummy columns including consolidating as per standard speciation curing etc. complete (cement concrete 1:2:4 for slabs to be extended upto top of splashing with pressed tiles and future extension roads to be embedded in cement concrete 1;3;6DUMMY COLUMN should be at least in 1m height).

Manufacturing , supplying and fixing of stainless steel hand rails for staircase using 50 mm dia 304L grade stainless steel pipe of 1.60 mm thick at required locations to a height of 900 mm from finished floor level welded to 38 mm dia stainless steel pipe post of 1.00 mm thick as vertical at 900 mm centre to centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.6 mm thick in between . The vertical pipe has to be welded to the 100x 100 x 6 mm MS base plate encased in the base concrete.The rate is inclusive of the charges for cutting, bending , welding , grinding , polishing , conveyance , electrical charges etc.complete

Manufacturing , Supplying and fixing of stainless steel hand rail for staircase near wet riser using 50 mm dia 304L Grade stainless steel pipe of 1.60 mm thick will be provided with tubular supports mAade of 304L Grade stainless steel pipe of 25 mm dia of 1.60 mm thick welded to the railing . The supports will be grouted into the wall and provided with 93.00 mm thick stainless steel circular base plate of 304 grade . The rate shall included for grouting into concrete with necessary supporting arrangemetns the hand rail in floor polishing buffing , bonding, cutting, grinding,conveyance, welding charges, electrical charges , etc. complete.

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil)

Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches concealed in suitable TW box covered with hylem sheet in flush with wall with earth connection (for computer plug socket)

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch on suitable TW Box

Supply and fixing of 4'20W twin LED type fluorescent fittting complete with copper choke and condensor with conduit pipe suspension from ceiling with PVC unsheathed copper leads from terminals to the fitting with fluorescent Tubes

Supply and fixing of 30W twin street light LED fitting complete with copper choke and condensor with 32mm dia GI pipe (Class 'B') with 1 No. 32mm GI bend complete on the existing post wall with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads MS clamps and aluminium painting with fluorescent tubes

Supply and fixing of 1200 mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod on existing clamp

Supply and fixing of horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door of double door type with metal door with IP43 protection with 40A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (like standard make)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board of double door type with metal door with IP43 protection with 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like Legrant / haggen make.standard

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supplying and fixing of Polycarbonate Sheet 6mm thick fully corrugated sheet for head room roof with necessary adjustable ridges seater on 'U' or 'J' bolts complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position 'B' Class GI pipes of size 50mm for holding the AC sheet roof including dismantling the masonry etc. including one coat of red oxide primer.

Supply and laying of 4X16 sq.mm. PVC LTUG aluminium armoured cable PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 4 x 25 sq.mm. LTUG armoured cable with earth connection

Supply and clamping of 32mm dia GI pipe on post or on wall with MS clamps and painting of sutiable colour.

GST 18%