Hindu Religious Institutions And Charitable Endowments Tender
Search from a plethora of business opportunities for Tamil Nadu tenders posted on the eProcurement TamilNadu website and other online and offline sources. Here, on BidAssist, you can find the best tender opportunities to boost your enterprise by finding work in Tamil Nadu government tenders, PSUs, Municipal Corporations and more. Read on to learn about the bidder registration process, DSC and more.
Hindu Religious Institutions And Charitable Endowments - HRICE Tender
Civil And Construction
Building Construction
Eprocure
Opening Date2 Dec 2024
Closing Date3 Jan 2025
Tender AmountRefer Documents
Costs
EMD
₹ 12,15,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_HRCE_505830_1Bid Award Id
ViewTender No
449/867210/2024Tender Authority
Hindu Religious Institutions And Charitable Endowments ViewPurchaser Address
-Website
http://tntenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Tender Documents,Drawing ,General Terms and conditions
BOQ Items
... More
600mm dia of pile 910 KN safe load
2
-
-
... More
Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including mobilization charges, labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.
-
-
-
... More
600mm dia of pile 910 KN safe load
2
-
-
... More
Earth work excavation and desposting on banks with initial lead of 10m and initial lift of 2m in hard stiff clay, stiff black cotton soil, hard red earth, shales, murram, gravel, stony earth and earth mixed with small size boulders et., As per SS 20B excluding hard rock requiring blasting inclusive of shoring shuttering, baling ojut water where ever necessary and including refilling consolidation etc., complete in all respects complying with relevent standard specifications and as directed by departmental officers.
166
-
-
... More
Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentrations raft slab and beam, under Cellular raft slab, around the footings, column pits, trenches, pits, wall trenches, back fill, plinth filling, junction of wall and floor, side walls of foundation, external perimeter of building, surrounding of pipes expansion joints, etc. as per IS specification and as per the instructions of chemical manufacturer and all as directed.The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 (PART-2) or equivalent BS specification.
1677
-
-
... More
Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification.
188
-
-
... More
Plain Cement Concrete 1 : 5 :10 ( one part of cement, five parts of sand and ten parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement.
188
-
-
... More
Supplying and Filling Gravel in foundation and basement in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.
504
-
-
... More
Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.
-
-
-
... More
For Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members
1500
-
-
... More
For Vertical surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.
176
-
-
... More
for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.
1949
-
-
... More
For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.
7306
-
-
... More
Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.
3600
-
-
... More
Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
-
-
-
... More
Foundation & Basement
404
-
-
... More
Ground Floor
89
-
-
... More
First Floor
73
-
-
... More
Second Floor
89
-
-
... More
Third Floor
89
-
-
... More
Fourth Floor
7
-
-
... More
Providing and laying in position, Standardised Concrete Mix M-35 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
-
-
-
... More
Ground Floor
451
-
-
... More
First Floor
477
-
-
... More
Second Floor
438
-
-
... More
Third Floor
438
-
-
... More
Terrace Floor
29
-
-
... More
Post Tensioning Work:
Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths,supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables,end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting,packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry
mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the
Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.
-
-
-
... More
PT Slab & PT Beam
26.6
-
-
... More
Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)
412.5
-
-
... More
Brickwork in Cement Mortar 1:5(One cement and five sand) using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" in foundation, basement and superstructure including curing etc. complete complying with standard specification.
-
-
-
... More
Foundation & Basement
20
-
-
... More
Brickwork in Cement Mortar 1:6(One cement and six sand) using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" in foundation, basement and superstructure including curing etc. complete complying with standard specification.
-
-
-
... More
First Floor
128
-
-
... More
Second Floor
118
-
-
... More
Third Floor
201
-
-
... More
Terrace Floor
55
-
-
... More
Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Bricks of size 9'' x 43/8" x 23/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc.complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately).
453
-
-
... More
Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers
5173
-
-
... More
Plastering with Cement Mortar 1:5 for Internal walls & External walls (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.
11928
-
-
... More
Dadooing walls with best approved quality, white / colour glazed tiles of size 450x300x8mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.
1193
-
-
... More
Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 600 x 600 x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/Sqm laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge. (Including Skirting work)
3608
-
-
... More
Flooring with following ceramic tiles of size Joint Free Rectified Ceramic tile of Size- 305 x 305 x 8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
327
-
-
... More
Supply & Laying with the best quality approved kotta stone slab not less than 20mm thick and the size of slab in general not less than 1200 X 600 mm machine cut and machine high pre - polished set in C.M 1:4 20 mm thick with white cement sluury for surface contact of the bottom of the kotta slab as per approved pattern / design as per the drawings by using irrespective of size and shapes including finishing the joints with white cement sluury, cutting, edge chamfering and polishing rough, medium nice and acid wash and tin - oxide polish. Rate including all materials labour Charges, wastages, Necessaryleads & lifts working at all levels transportation charges loading and unloading, preparation of surfaces, necessary hacking in RCC surfaces cutting to required shape tool, and plants fuel, curing, cleaning acid wash over finished surfaces, protection with Gypsum / Pop layer over plastic sheet and removing the same before handling over as complete with all respects complying with relevant standard specifications and as directed by the Client / Engineer in Charge
230
-
-
... More
Paving the floor with best approved quality Natural flammed finish granite for flooring/ steps & Landing of 18 / 20mm thick of with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification
653
-
-
... More
Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.
26
-
-
... More
Supplying and Paving the Paver Block flooring using Rubber mould paver block (Colour) of standard size over the sand filling of 83mm thick, including laying Compacting with power machine including loading transportation and colour pigments of paver blocks, including cost and conveyance of all materials labour etc complete with standard specification.
1023
-
-
... More
Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.
109
-
-
... More
Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed.Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.
1088
-
-
... More
Paving the Top of roof with Solar refelective tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)
1105
-
-
... More
UPVC Window :Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm125GSMand 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates ashandle. The corners and joints should be welded andcleaned. Radiations free pin headed plain or browncolour glass 4mm thick should be provided to theshutter and it should not allow leakage of water evenat most ranging storms and should have key lockableaction, security protective hinges, strong lockingsystems and as per size for arresting noise and energyloss. The connecting mechanism between sash andouter frame that enables opening of the window. Thewindow should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on work.
135
-
-
... More
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (blackcolour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the
Executive Engineer before use on work
22
-
-
... More
Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish of single leaf fully panelled sliding door with 12mm thick bothside prelaminated partile board at the Shutter bottom rail:100x44.45x2.50mm@1.974 kg/m,Top & Verticle 50x44.45x2.50mm @ 1.292 kg/m,Lock rail 50x44.45x2.50mm @ 1.292 g/m, Running channel section:50x44.45x2.50mm@1.292 kg/m, and necessary accessories such as Alu.clips 17.15x17.27x1.50mm @ 0.176 kg, Alu handle 100x30mm @ 0.988 kg/mfull length of handles on both sides, lock, roller, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and waking hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete. All the Alu. sections are to be anodised.with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc.,
9
-
-
... More
Structural Glazing:
Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to beused as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS, 875.Paint specifications: Primer coat with epoxy primer of 5-7microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7microns or powder coated with pure polyester powder upto50-60 microns thick.Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.
248
-
-
... More
Double leaf full glass door:To be made out of 12mm thk Toughened glass with etching as per design .The glass with etching has to be fixed. with all side and Top rails of size 1 1/4" x 5" and the Bottom rail of size 1 1/2" x 10".The rails to be made out of best quality beach wood.The door shall have 18" long S/S handle and also 2 nos of double action floor spring of specified make. The etching in glass pattern to be followed strictly as per instructions of the Architect or following the drawing attached.NB: Size of the door may slightly vary as per site conditions for matching the elevation of the fixed glazing. All exposed edges of the glass to be machine polished.dorma/Eqivalent patch fitting and locking arrangement is to be used for fixing the glass.
268
-
-
... More
Solid PVC door shutters Toilet door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.
98
-
-
... More
Door Frame: Supplying and fixing first quality teak wood frames for doors, windows, ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc. complete in all floors.
-
-
-
... More
Teak wood Scantings up to 2M
1
-
-
... More
Teak wood Scantings over 2M and below 3M
3
-
-
... More
Supply & Fixing of Single Leaf Solid core Flush shutters with Teak ply on both side with teak wook lipping alround 35 mm thick, with necessary adhesives and CP screws complying with standard specification.The cost is inclusive of 1 No Lock arrangement, handel, tower bolt ,approved equivalent make SS ball bearing hinges of quivalent make of aproved make, 2 no floor mounted SS door stoper ect.complete as per drawing.
63
-
-
... More
Supply & Fixing of 35mm thk.Double leaf high density interior grade marine plywood shutters pasted both sides 1.5mm thk.laminate approved design with 35x12mm T.W.lipping on all edges with necessary adhesives and CP screws complying with standard specification.The cost is inclusive of 1 no Lock arrangemen,handel,tower bolt ,approved equivalent make SS ball bearing hinges of quivalent make of aproved make,2 no floor mounted SS door stoper ect.complete as per drawing. Make:Kutty,Sharon,Trojan. Accessories Make:Dorma, Godrej.
57
-
-
... More
Providing and fixing welded M.S. grills to the window openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Engineer-in-charge.
4250
-
-
... More
Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of all materils, Labour charges for cutting, bending, welding, grinding, polishing, Transportation, electrical charges, etc. complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.
127
-
-
... More
Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)
170
-
-
... More
Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
238
-
-
... More
Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).
5173
-
-
... More
Providing and applying Emulsion paint finish of approved make & shade in two coats over a coat of approved primer and 2 coats of patty to give an even shade as per manufacturer's instruction to the internal plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.
9259
-
-
... More
Providing and applying Emulsion paint finish of approved make & shade in two or more coats over a coat of approved primer to give an even shade as per manufacturer's instruction to the external plastered surfaces and internal ceiling plastered surfacesincluding preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.
2669
-
-
... More
PLUMBING WORKS:-
-
-
-
... More
PART A - SANITARY FITTINGS:-
-
-
-
... More
Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittingssuch as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
58
-
-
... More
Supplying and fixing of 15mm CP two way bib cock with health faucet of parryware or equivalent make conforming to BIS specification and quality including cost of shellac, thread etc., complete complying with standard specification and including cutting and threading wherever necessary.
58
-
-
... More
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
62
-
-
... More
Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).
62
-
-
... More
Over head Shower: Supplying & Fixing in postion of CP Shower Rose with CP Stop cock arrangements of size 15mm inlet 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac Etc.,Complete complying with standard specification and as directed by departmental officer. ( The CP Shower rose should be got approved by the Executive engineer before use on Works
18
-
-
... More
Supplying & fixing of Angle valve stopcock with connecting hose and wall flange. (Make: Parryware or equivalent)
120
-
-
... More
Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc.,complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).
22
-
-
... More
Supply & fixing C.P soap tray of approved quality (Parryware or equivalent) including cost and conveyance complying with standard specification.
60
-
-
... More
Supplying & fixing of Long body Bibcock with brackets including fixing over Wall tile dado complete.(Make: Parryware or equivalent)
128
-
-
... More
PART - B SOIL AND WASTE PIPES
-
-
-
... More
Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition,including testing for any leakages,etc.,complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below Stilt level.
-
-
-
... More
40mm dia. 6kg class PVC pipes.
396
-
-
... More
50mm dia. 6kg class PVC pipes.
484
-
-
... More
75mm dia. 6kg class PVC pipes.
966
-
-
... More
110mm dia. 6kg class PVC pipes.
484
-
-
... More
Supplying and fixing in position cost iron Nahini / Floor trap with Stainless steel grating / PVC nahini / Floor Trap with PVC Grating type of size 100 x 75 / 75 x 50 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1;2;5 (One lime two sand and five aggregate ) brick jelly 40mm and finishing with cm 1;3(One cement and three sand) including dismantling masonary wherever found necessary and making good to the original condition and giving connections to the cast iron pipe etc, complete complying with standard specififcation and as directed by the departmental Officers.
120
-
-
... More
RAIN WATER PIPE:-
-
-
-
... More
Supply and fixing in position best quality PVC IS 4985 - CLASS-II - 4 Kg/Sqcm -Rain water pipes of various size having ISI mark and providing leak proof joints with such as Bend, Tee Junction, door etc.,of approved qualityincluding fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, wherever necessary and making chipping good to the original condition, complying with standard specification etc.,complete.
-
-
-
... More
110mm dia
192
-
-
... More
Supplying and fixing in position of the following dia PVC rain water gratings for rain water pipes ,of approved quality and variety of various size confirming to ISS and including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer.
-
-
-
... More
100mm dia
9
-
-
... More
Supplying and fixing in position of the following dia PVC specials such as PVC vent Cowl etc.,of approved quality and variety of various size confirming to ISS amend providing leak proof joint etc., including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer.
-
-
-
... More
110mm dia
9
-
-
... More
PART-C EXTERNAL DRAINAGE
-
-
-
... More
Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition,including testing for any leakages,etc.,complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below Stilt level.
-
-
-
... More
75mm dia
97.8
-
-
... More
110mm dia
151
-
-
... More
160mm dia
377
-
-
... More
Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.
40
-
-
... More
Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.
10
-
-
... More
Internal Concealed Works
-
-
-
... More
Providing, supplying & laying of Chlorinated Poly Vinyl Chloride (CPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability with brass and CPVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step CPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, etc all complete as per as per specifications, Exposed work including chase cutting, bracket fixing)complete complying with standard specification and as directed by the Departmental Officer.
-
-
-
... More
20mm dia
16
-
-
... More
25mm dia
87
-
-
... More
32mm dia
50
-
-
... More
PART F.EXTERNAL PLUMBING WORKS
-
-
-
... More
Providing, supplying & laying of Unplasticized Polyvinyl Chloride (UPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour, transportation,tools & tackles all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer.
-
-
-
... More
32mm dia
80
-
-
... More
40mm dia
180
-
-
... More
50mm dia
34
-
-
... More
Providing, supplying & laying of Gunmetal type NRV - pressure rating less tahn 16 Kg/Sqcm and IS778 with 2 Nos of MTA with jointing material like shellac, thread including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications, complete complying with standard specification and as directed by the Departmental Officer
-
-
-
... More
32mm dia
6
-
-
... More
40mm dia
6
-
-
... More
50mm dia
6
-
-
... More
Supplying and erection of horizontal shaft centrifugal mono block power pump set of single phase 2.00 H.P of best approved quality and make with ISI mark on suitable pedastal with foundation bolt and nut including labour supplying and fixing of starter and main switch suitable for 2.00 H.P pumpset on suitable angle iron frame work with necessary labour including panel board, supply and run off 4 of 10 Sq,mm, in P V C pipe with 14 SWG TC wire including fixing of suction pipe and foot valve up to a maximum depth of 7m and delivery pipes upto the exterior wall of pump room etc., complete and operating the pumps on trial run for 3 days. (The make and quality of pump set to be got approved by the Executive Engineer before use on works.) (TWAD- Pa no:103 Sl.no:45)200mx60m
2
-
-
... More
BOREWELL:-
-
-
-
... More
Drilling of bore wells in alluvial soil or sedimentary strata of clay and sand or sand stone, shale, pebbles, boulders etc., by first taking a pilot bore of 150 mm dia and then enlarging to the required dia by direct or reverse rotary mud circulation method including charges for all T&P, cost of fuel, labour charges, bentonite mud and water required for drilling at the site shown by the departmental officers including construction of mud pit etc., complete.
-
-
-
... More
Upto 60 m Depth ending below ground level
60
-
-
... More
From 60 m to 90 m Depth ending below ground level
30
-
-
... More
Reaming 150mm dia Pilot bore to 300mm dia bore as directed by the departmental officers upto required depth
-
-
-
... More
Upto 60 m Depth ending below ground level
60
-
-
... More
From 60 m to 90 m Depth ending below ground level
30
-
-
... More
Supplying, and fixing the following size of PVC pipes of approved quality and variety conforming to pressure IS 4985. The rate is inclusive of cost of pipe, all taxes, conveyance charges of materials and all other labour charges for fixing the PVC pipe as directed by the departmental officers etc., complete complying with standard specifications. The PVC pipe should be got approved by the departmental officers before use on work and Labour Charges for insering PVC casing pipe assembly (with slots and without slots) in the drilled holes including jointing the pipes with PVC couplers with PVC adhesive etc., complete and supplying and packing annular space with pebbles of size and quality as approved by the Departmental Officers.
-
-
-
... More
150mm dia PVC Casing Pipe (With or without Slot)
90
-
-
... More
Labour for inserting pipe
90
-
-
... More
Charges for developing Borewell with air compressor of 600 CFM capacity (Min 8 Hours) including transportation and labour and fuel charges for the compressor as directed by the departmental officers and conducting yeild test by 'V' notch methods, excluding cost of bore charges and conveyance charges for handling boring
8
-
-
... More
Supply, errection and giving necessary water supply and electrical connections of new type 2 HP submersible pumpset confiming to IS-14220 with ISI mark suitable for 150mm borewell, complete complying with standard specification including suitable 3-phase panel board with DOL with two level guard starter and accessories and Labour charges for the erection of submersible pump set in bore well including fixing and jointing the submersible cable ( but excluding cost of 2.50sqmm - 3core copper cable)with proper clamps upto othe starter to the required depth, valves section clamps, pressure gauges upto the exterior wall of the panel board consisting of JPICN switch starter, voltammeter, ammeter, 3 pilot (indicating) lamps, capacitor, single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per I.E. rules etc. complete and testing pump sets on trial run for 3 days etc., complete complying with standard specifications. with Three phase panel board
1
-
-
... More
Suppling and fixing PVC bore well end cap of size 165/168mm dia etc., complete complying with standard specifications as directed by departmental officers
1
-
-
... More
Supply of 4.00 Sq.mm / PVC insulated and sheathed, 3 core flat type copper cable for submersible motor complete complying with standard specifications as directed by departmental officers
120
-
-
... More
Supply and fixing the Nylon Rope to connect the Submersible motor in borewell etc., complete complying with standard specifications as directed by departmental officers
90
-
-
... More
ELECTRICAL WORK:-
-
-
-
... More
Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) (Higher End ) (Data A1)
927
-
-
... More
Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End (Data A2 )
162
-
-
... More
Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End (SD308)
38
-
-
... More
LIGHT FIXTURES
-
-
-
... More
Supply and fixing of 4' 20W LED fitting with LED on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end)(Data A3)
397
-
-
... More
Supply and fixing of 4' 20W LED fitting with LED on conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end) (Data A4)
19
-
-
... More
Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb (SD 84)
61
-
-
... More
supply and fixing of 18W LED square type Surfcace/Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting (SD 441)
108
-
-
... More
supply and fixing of 24W LED 2x2 square type surface/ Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.(SD 439)
203
-
-
... More
supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .(SD 448)
7
-
-
... More
Supply and fixing of LED fitting of 2000 lumens cpacity surface and suspended cylindrical downlighting With its differentiated aesthetics of extruded aluminium housing and a superior powder coated finish,uniform lighting distribution and superior features of driver when it comes to the surfce/ cylinderical downlight category with PVC unsheahted leads from terminals to the fitting.(Higher end) (Data A5)
128
-
-
... More
Supply and fixing of 20W LED Mirror light fitting on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end)(Data A6)
22
-
-
... More
FANS
-
-
-
... More
supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod on the existing fan clamp (SD 482)
122
-
-
... More
Supply and fixing of 300mm (12") sweep (Heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall (Data A7)
23
-
-
... More
Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)
23
-
-
... More
Supply and fixing of 375mm (15") sweep (Heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall (Data A7)
24
-
-
... More
Supply and fixing of louvers shutters arrangements for 375mm (15") sweep (light duty) AC exhaust fan (SD 121)
24
-
-
... More
WALL SOCKETS
-
-
-
... More
Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 383)
144
-
-
... More
Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 401)
61
-
-
... More
Supply and fixing of 1 no.6/16A two module socket with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections.(for Geycers) Higher End (Data A9 )
18
-
-
... More
Supply and fixing of 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (for Geycers)Higher End (Data A10)
18
-
-
... More
ELECTRIC WATER HEATER
-
-
-
... More
Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection (SD 104)
18
-
-
... More
DISTRIBUTION BOARDS
-
-
-
... More
Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 514)
5
-
-
... More
Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 526)
24
-
-
... More
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 573)
9
-
-
... More
Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 125A 4P MCCB switch as incoming and 4 nos. 63A 3P MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End (Data A11)
4
-
-
... More
Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 125A 4P MCCB switch as incoming and 2 nos. 63A 3P MCB , 4 nos. 6-32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End (Data A12)
2
-
-
... More
Supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 125A 4P MCCB switch as incoming and 5 nos. 63A 3P MCB , 3 nos. 6-32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End (Data A13)
1
-
-
... More
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 2 nos. 32A 3P MCB , 4 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data A 14)
2
-
-
... More
Supply and fixing of 32A DP MCB with sheet steel enclosure in flush wall with earth connection (Higher end) (Data A15)
19
-
-
... More
Supply and fixing of 32A 4P MCB with sheet steel enclosure on wall with earth connection (Higher end) (Data A 16)
3
-
-
... More
RUN OF MAINS
-
-
-
... More
Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion (SD 337)
500
-
-
... More
Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour (SD 57)
1200
-
-
... More
Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour (SD 59)
1000
-
-
... More
Supply and run of 4 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour(SD 61)
150
-
-
... More
Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm copper wire and making good of the concealed portion with suitable colour (SD 63)
500
-
-
... More
UG CABLES
-
-
-
... More
Supply and clarnping of 4 x 16 sq.mm. PVC LTUG armoured copper cable on post or on wall with MS clamps (Data A17)
15
-
-
... More
Supply and fixing of brass cable gland for 4 x 16 sq.mm. LTUG armoured copper cable with earth connection (SD 163)
2
-
-
... More
Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG alu. cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (SD 659)
50
-
-
... More
Supply and clarnping of 3 1/2 x 25 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (SD200)
150
-
-
... More
Supply and fixing of brass cable gland for 3 1/2 x 25 sq.mm. LTUG armoured alu. cable with earth connection (SD 164)
6
-
-
... More
Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 213)
6
-
-
... More
Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG alu. cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (SD 660)
50
-
-
... More
Supply and clarnping of 3 1/2 x 35 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (SD201)
100
-
-
... More
Supply and fixing of brass cable gland for 3 1/2 x 35 sq.mm. LTUG armoured alu. cable with earth connection (SD 165)
8
-
-
... More
Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 214)
8
-
-
... More
Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG alu. cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (SD 661)
50
-
-
... More
Supply and clarnping of 3 1/2 x 50 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (SD202)
200
-
-
... More
Supply and fixing of brass cable gland for 3 1/2 x 50 sq.mm. LTUG armoured alu. cable with earth connection (SD 166)
6
-
-
... More
Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 215)
6
-
-
... More
Supply and Laying of 2 runs of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Data A18)
60
-
-
... More
Supply and clarnping of 2 runs of 3 1/2 x 150 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (Data A 19)
70
-
-
... More
Supply and fixing of brass cable gland for 3 1/2 x 150 sq.mm. LTUG armoured alu. cable with earth connection (SD 170)
8
-
-
... More
Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 219)
8
-
-
... More
Supply and Laying of 2 runs of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Data A20)
200
-
-
... More
Supply and clarnping of 2 runs of 3 1/2 x 185 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (Data A 21)
150
-
-
... More
Supply and fixing of brass cable gland for 3 1/2 x 185 sq.mm. LTUG armoured alu. cable with earth connection (SD 171)
28
-
-
... More
Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 220)
28
-
-
... More
Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG alu. cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (SD 657)
500
-
-
... More
Supply and clarnping of 4x10 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (SD 198)
50
-
-
... More
Supply and fixing of brass cable gland for 4 x10 sq.mm. LTUG armoured alu. cable with earth connection (SD 163)
34
-
-
... More
EXTERNAL LIGHTS
-
-
-
... More
Supply and clarnping of 4x10 sq.mm. PVC LTUG armoured alu. cable on post or on wall with MS clamps (SD 198)
16
-
-
... More
Supply and fixing of brass cable gland for 4 x10 sq.mm. LTUG armoured alu. cable with earth connection (SD 163)
16
-
-
... More
DIESEL GENERATOR SET
-
-
-
... More
Supply, Erection, Testing, Commissioning and Handing over of 1 No 250 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM (CPCB IV + Norms and BIS Specification) as detailed below with AMF panel.
1
-
-
... More
1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 600 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000.
-
-
-
... More
The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent)
-
-
-
... More
1. Dry type Air cleaner
-
-
-
... More
2. Expansion bellow
-
-
-
... More
3. Radiator, Radiator fan and mounting
-
-
-
... More
4. Air to air charge cooler
-
-
-
... More
5. Exhaust Gas turbo charger
-
-
-
... More
6. Lube oil cooler and Lube oil filter
-
-
-
... More
7. Fuel filter(pre and micro
-
-
-
... More
8. In-line Mono-block fuel injection pump with governor and fuel feed pump
-
-
-
... More
9. Electronic governor
-
-
-
... More
10. 24V Battery charging alternator
-
-
-
... More
11. 24V Volt electric starter motor
-
-
-
... More
12. Engine test Certificate
-
-
-
... More
13. Residential Mufler
-
-
-
... More
14. Fly wheel with starter ring.
-
-
-
... More
ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator.
-
-
-
... More
SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device
-
-
-
... More
1. Low lubricating oil pressure
-
-
-
... More
2. High Water temperature
-
-
-
... More
3. Vee-belt failure and over speed
-
-
-
... More
4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load
-
-
-
... More
2. ALTERNATOR : Alternator capacity of 250 KVA/ 200 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.)
-
-
-
... More
3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process
-
-
-
... More
of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt
-
-
-
... More
distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank
-
-
-
... More
The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package:
-
-
-
... More
Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be
-
-
-
... More
unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade.
-
-
-
... More
4. FUEL TANK : 350 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance.
-
-
-
... More
5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely
-
-
-
... More
coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges.
-
-
-
... More
Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ ceiling with connection (For AMF to 250KVA Genset) (Data A23)
40
-
-
... More
Supply and installation of exhaust piping of sufficient length with suitable MS clamps so as to extend outside the generator room with necessary thermal insulation, (SOR M 2085)
5
-
-
... More
Construction of RCC foundation of suitable for 250KVA Gen set weight approximately weight 5000 kg with cement concert 1:2:4 with sand cushion all around the foundation for the erection of 250 KVA DG set with proper alignment
1
-
-
... More
Provision for Diesel for testing and first running of 250 KVA DG set
100
-
-
... More
EARTHING
-
-
-
... More
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)
20
-
-
... More
Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection. (SD 76)
70
-
-
... More
Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth Connection (SD 371)
600
-
-
... More
PANEL BOARDS
-
-
-
... More
Supply, erection, testing and commissioning of 630A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following 1 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set
1
-
-
... More
Incoming 1)Supply and fixing of 1 No. 630A 4 pole 50 ka , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout,
-
-
-
... More
features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification.
-
-
-
... More
Outgoing
-
-
-
... More
1) Supply and fixing of 400A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-3Nos
-
-
-
... More
Inter connecting the all LT ACB’s and switches to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to
-
-
-
... More
the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules .Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning ( DATA-A24 ) (L&T,C&S,SIEMENS,ABB)
-
-
-
... More
Supply, erection, testing and commissioning of 630A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following 1 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set
1
-
-
... More
Incoming 1)Supply and fixing of 1 No. 630A 4 pole 50 ka , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout,
-
-
-
... More
features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE/CEA-2023 rules in force with inter connection and terminations as required in specification.
-
-
-
... More
Outgoing
-
-
-
... More
1) Supply and fixing of 400A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-2Nos
-
-
-
... More
2)Supply and fixing of 200A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-3Nos
-
-
-
... More
3)Supply and fixing of 125A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-6Nos
-
-
-
... More
4)Supply and fixing of 63A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-2Nos
-
-
-
... More
5) Multifunction meter - 1 no., 3 nos. Pilot lamp with control switch -1 set.
-
-
-
... More
Inter connecting the all LT ACB’s and switches to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to
-
-
-
... More
the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules .Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning ( DATA-A25 ) (L&T,C&S,SIEMENS,ABB)
-
-
-
... More
Supply, erection, testing and commissioning of 630A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following 1 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE/CEA-2023 rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set
1
-
-
... More
Incoming 1)Supply and fixing of 1 No. 630A 4 pole 50 ka , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout,
-
-
-
... More
features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE/CEA-2023 rules in force with inter connection and terminations as required in specification.
-
-
-
... More
Outgoing
-
-
-
... More
3)Supply and fixing of 125A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-9Nos
-
-
-
... More
4)Supply and fixing of 63A TPN switch disconnector Fuse units inrerior only with HRC fuses double break-7Nos
-
-
-
... More
5) Multifunction meter - 1 no., 3 nos. Pilot lamp with control switch -1 set.
-
-
-
... More
Inter connecting the all LT ACB’s and switches to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to
-
-
-
... More
the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules .Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning ( DATA-A27 ) (L&T,C&S,SIEMENS,ABB)
-
-
-
... More
Automatic Transfer switch
-
-
-
... More
Supply and fixing of Automatic Transfer switch of 630A capacity with the following specification: Mode of operation :selection mode :Auto/maual/(Remote/RS485-Optional ) salient features.
2
-
-
... More
1.Automatic Start/Stop Operation of DG on mains failure.
-
-
-
... More
2.Fire alarm / External fault trip features is provided.
-
-
-
... More
3.Inbuilt control switch for selecting auto/manual mode .
-
-
-
... More
4.High capacity to withstand short circuit.
-
-
-
... More
Mounted on suitable MS panel of size 3'x3.5'x2' with MS channel for mounting with 3mm thick hylem sheet seperation for switch and cable adopter box with selection plate and 1'x1' size view glass arrangements on single door on suitable Angle iron support for floor/wall mounting with necessary connection
-
-
-
... More
(Data A27)
-
-
-
... More
LTCT METER PANEL
-
-
-
... More
Supply ,Erection ,Testing and commissioning of Three compartment LTCT meter box made up of 16 SWG CRCA sheet steel ( Length 1200mm x Height 1200mm x width 600mm) with door and lock & key arrangements on suitable angle iron frame support for floor / wall mounting support with supply and fixing of the following interior mounting arrangements with busbar chamber, meter chamber and Terminal box chamber confirming to IE/CEA-2023 rules.
2
-
-
... More
i.The busbar chamber will consist of 4 nos. 2” x 1/4” tinned copper flat for phase and neutral busbar on epoxy mounted bus insulated at proper and sufficient spacing between the bus bar as per IE/CEA-2023 Rules.
-
-
-
... More
ii. 3 nos. 630/5A CT coil mounted in Three phase busbar.
-
-
-
... More
iii. Interconnection between CT coil to 4 way terminal box and 4 way terminal box to Meter box by 4 sq.mm PVC cu.wire.
-
-
-
... More
iv.630A Din type HRC fuse unit with base -3 nos. For 3 phases and 1 no. 0.5 feet length 2"x1/2"cu.flat for neutrl link
-
-
-
... More
The LTCT meter box should be powder coat paint of approval colour , approved by site officer. (Data A 22)
-
-
-
... More
LIFTS
-
-
-
... More
Design, engineering, supply, erection, testing, commissioning and handling over of the 20 persons capacity (1360 kg) Bed cum passenger lift, gearless with machine room as per the following technical specification:
1
-
-
... More
TECHNICAL SPECIFICATIONS:-
-
-
-
... More
1) Location: Kalyanamandapam (Lift no.5)
-
-
-
... More
2) No. of lifts / Type of Lift: one /Bed cum Passenger lift
-
-
-
... More
3) Capacity of lift: 20 persons capacity (1360 Kgs) Bed cum passenger lift
-
-
-
... More
4) Speed: 1.0 Mtr Per Second.
-
-
-
... More
5) Type of Drive: Microprocessor based Variable Voltage Variable frequency (V3F) drive with enhanced ride comfort and levelling functions.
-
-
-
... More
6) Position of Machinary: Directly above the lift well - GEARLESS
-
-
-
... More
7) No of floors: G+4 (5 landings)
-
-
-
... More
8) Total travel : 18 Mtrs
-
-
-
... More
9) Leveling accuracy:- High level accuracy with smooth and jerk free stopping.
-
-
-
... More
10) Design of car: Stainless Steel hairline finish combination car body with SS finish ceiling (sleek medium circular LED lights, regular circular fans SS Handrail & PVC flooring.
-
-
-
... More
11) No. of landing entrance : 5 nos (G.F+4 F)
-
-
-
... More
12) No. & position of car entrance : one in front only.
-
-
-
... More
13) Size of lift well: 2200 mm x 3000mm (Width x depth)
-
-
-
... More
14) Lift Car inside size: 1300mm x 2400mm x 2200mm (width x depth x height)
-
-
-
... More
15) Lift pit & head room: 1600mm deep, Head room 4800 mm height.
-
-
-
... More
16) Car clear opening: 1000mm x 2000mm (width x height) Lintel - 2200mm
-
-
-
... More
17) Landing entrance door: Power operated V3F door, Centre opening sliding door - stainless steel (1.5 mm) - hairline finish.
-
-
-
... More
18) Landing entrance frame: stainless steel - hairline finish.
-
-
-
... More
19) Control:- Microprocessor based Simplex selective collective control with / without attendant.
-
-
-
... More
20) Indication: Dot Matrix LED Direction & Position Indicators in car & landings. Puch button;_orange LED illumination.(Diabled friendly)
-
-
-
... More
21) Emergency Alarm Bell: Battery operated alarm bell to be provided with automatic charging device.
-
-
-
... More
22) Emergency light: Battery operated light to be provided with automatic charging device.
-
-
-
... More
23) Fireman's switch : To be provided at ground floor.
-
-
-
... More
24) Minor builder works: To be provided by lift contractor.
-
-
-
... More
25) Scaffolding: To be provided by lift contractor.
-
-
-
... More
26) Stainless steel Sill angles and facia plates: To be provided by lift contractor.
-
-
-
... More
27) Steel for lift machinary :- To be provided by the lift contractor.
-
-
-
... More
28) Servicing and maintenance: Lift contractor should provide free comprehensive servicing and maintenance during the guarantee period.
-
-
-
... More
29) Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc. Complete with all accessories.
-
-
-
... More
30) Provision if Intercom with phone:- To be provided by the lift contractor
-
-
-
... More
31) Lift license: Preparation of drawings, lift contractor should do payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act.
-
-
-
... More
32) Floor announciator with music: To be provided in the car.
-
-
-
... More
33) Special features:
-
-
-
... More
(a) Battery Operated Emergency Light and Alarm Bell
-
-
-
... More
(b) Call Register Signal And Vf Door Operator
-
-
-
... More
(c) Automatic Rescue Device.
-
-
-
... More
(d) Stainless Steel Button with S.S. Cover.
-
-
-
... More
(e) Dot Matrix Led D & P Indicators in Car & Landings - Orange Colour.
-
-
-
... More
(f) Floor Annunciator with Music.
-
-
-
... More
(g) Firemans Switch
-
-
-
... More
(h) False Ceiling in Car.
-
-
-
... More
(i) Fire Rating of Landing Doors-One Hour
-
-
-
... More
(j) Infra Red Door Screen
-
-
-
... More
(k) Overload warning Indicator
-
-
-
... More
(l) Laminated Mirror At Rear Side.
-
-
-
... More
(m) Scaffolding
-
-
-
... More
(n) Two way Intercom with press & speak in Cop
-
-
-
... More
(o) Provision for EBABX
-
-
-
... More
(p) Free Service for One Year
-
-
-
... More
(q) Pit Ladder
-
-
-
... More
(r) Ss Handrail
-
-
-
... More
(s) Lift License
-
-
-
... More
(t) Minor Builders Work
-
-
-
... More
(u) Provision for Cctv Camera - Ip (Cat6 Flat Travelling Cable)
-
-
-
... More
34) Over speed governor, phase failure and phase reversal relay, alarm bell, T Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression spring etc.
-
-
-
... More
35) Guarantee: Gurantee for the materials and lift firm should offer workmanship of equipments complete for a period of not less than one year. (SOR) (M-2374) (Rs.2750000 + 150000)
-
-
-
... More
Design, engineering, supply, erection, testing, commissioning and handling over of the 16 persons capacity (1088 kg) passenger lift, gearless with machine room as per the following technical specification:
4
-
-
... More
TECHNICAL SPECIFICATIONS:-
-
-
-
... More
1) Location: Kalyanamandapam (Lift no.1 to Lift no.4)
-
-
-
... More
2) No. of lifts / Type of Lift: Four / Passenger
-
-
-
... More
3) Capacity of lift: 16 persons capacity (1088 Kgs) passenger lift
-
-
-
... More
4) Speed: 1.5 Mtr Per Second.
-
-
-
... More
5) Type of Drive: Microprocessor based Variable Voltage Variable frequency (V3F) drive with enhanced ride comfort and levelling functions.
-
-
-
... More
6) Position of Machinary: Directly above the lift well - GEARLESS
-
-
-
... More
7) No of floors: G+4 (5 landings)
-
-
-
... More
8) Total travel :18 Mtrs
-
-
-
... More
9) Leveling accuracy:- High level accuracy with smooth and jerk free stopping.
-
-
-
... More
10) Design of car: Stainless Steel hairline finish combination car body with SS finish ceiling (sleek medium circular LED lights, regular circular fans SS Handrail & PVC flooring.
-
-
-
... More
11) No. of landing entrance : G+4 (5 landing)
-
-
-
... More
12) No. & position of car entrance : one in front only.
-
-
-
... More
13) Size of lift well: 2650 mm x 2500mm (Width x depth)
-
-
-
... More
14) Lift Car inside size: 2000mm x 1300mm x 2200mm (width x depth x height)
-
-
-
... More
15) Lift pit & head room: 1600mm deep, Head room 4800 mm height.
-
-
-
... More
16) Car clear opening: 900mm x 2000mm (width x height) Lintel - 2200mm
-
-
-
... More
17) Landing entrance door: Power operated V3F door, Centre opening sliding door - stainless steel (1.5 mm) - hairline finish.
-
-
-
... More
18) Landing entrance frame: stainless steel - hairline finish.
-
-
-
... More
19) Control:- Microprocessor based Simplex selective collective control with / without attendant.
-
-
-
... More
20) Indication: Dot Matrix LED Direction & Position Indicators in car & landings. Puch button;_orange LED illumination.
-
-
-
... More
21) Emergency Alarm Bell: Battery operated alarm bell to be provided with automatic charging device.
-
-
-
... More
22) Emergency light: Battery operated light to be provided with automatic charging device.
-
-
-
... More
23) Fireman's switch : To be provided at ground floor.
-
-
-
... More
24) Minor builder works: To be provided by lift contractor.
-
-
-
... More
25) Scaffolding: To be provided by lift contractor.
-
-
-
... More
26) Stainless steel Sill angles and facia plates: To be provided by lift contractor.
-
-
-
... More
27) Steel for lift machinary :- To be provided by the lift contractor.
-
-
-
... More
28) Servicing and maintenance: Lift contractor should provide free comprehensive servicing and maintenance during the guarantee period.
-
-
-
... More
29) Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc. Complete with all accessories.
-
-
-
... More
30) Provision if Intercom with phone:- To be provided by the lift contractor
-
-
-
... More
31) Lift license: Preparation of drawings, lift contractor should do payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act.
-
-
-
... More
32) Floor announciator with music: To be provided in the car.
-
-
-
... More
33) Special features:
-
-
-
... More
(a) Battery Operated Emergency Light and Alarm Bell
-
-
-
... More
(b) Call Register Signal And Vf Door Operator
-
-
-
... More
(c) Automatic Rescue Device.
-
-
-
... More
(d) Stainless Steel Button with S.S. Cover.
-
-
-
... More
(e) Dot Matrix Led D & P Indicators in Car & Landings - Orange Colour.
-
-
-
... More
(f) Floor Annunciator with Music.
-
-
-
... More
(g) Firemans Switch
-
-
-
... More
(h) False Ceiling in Car.
-
-
-
... More
(i) Fire Rating of Landing Doors-One Hour
-
-
-
... More
(j) Infra Red Door Screen
-
-
-
... More
(k) Overload warning Indicator
-
-
-
... More
(l) Laminated Mirror At Rear Side.
-
-
-
... More
(m) Scaffolding
-
-
-
... More
(n) Two way Intercom with press & speak in Cop
-
-
-
... More
(o) Provision for EBABX
-
-
-
... More
(p) Free Service for One Year
-
-
-
... More
(q) Pit Ladder
-
-
-
... More
(r) Ss Handrail
-
-
-
... More
(s) Lift License
-
-
-
... More
(t) Minor Builders Work
-
-
-
... More
(u) Provision for Cctv Camera - Ip (Cat6 Flat Travelling Cable)
-
-
-
... More
34) Over speed governor, phase failure and phase reversal relay, alarm bell, T Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression spring etc.
-
-
-
... More
35) Guarantee: Gurantee for the materials and lift firm should offer workmanship of equipments complete for a period of not less than one year. (SOR) (M-2364) (Rs.2200000+ 10000)
-
-
-
... More
APFC PANEL
-
-
-
... More
Supply and erection of 75 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 6 stage, (at 0.95 lag), made up of powder coated, 16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters.
2
-
-
... More
a. Vr – R phase Line Voltage
-
-
-
... More
b. Vy – Y phase Line Voltage
-
-
-
... More
c. Vb – B phase Line Voltage
-
-
-
... More
d. Ir – R phase Line current
-
-
-
... More
e. Iy – Y phase line current
-
-
-
... More
f. Ib – B phase Line Current
g. KW – Present Kilo Watts
h. RKVA – Present KVAR Demand
i. KVA – Present KVA j. PF – Present Power Factor
k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load m.Provision to indicate the change in phase Sequence n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection. Make. (Matrix /L&T /or equivalent (Data A26)
-
-
-
... More
Supply and run of GI Hot Dip/powder coated 16 SWG cable tray with 150mm width and 50mm height fixed by suitable anchor fasteners with bolts & washers complete (Data A30)
100
-
-
... More
Supply and run of GI Hot Dip/powder coated 16 SWG cable tray with 300mm width and 50mm height fixed by suitable anchor fasteners with bolts & washers complete (Data A31)
100
-
-
... More
supply and fixing of 630A,4 pole 50 KA , Microprocessor based ,EDO Air circuit breaker in sheet steel enclosured with AI frame support on wall/floor with necessary connection complete (Data A31 A)
1
-
-
... More
CCTV arrangments
-
-
-
... More
Supply and installation of 4MP IP Bullet /Dome camera with key features of 2.8/4/6mm fixed lens, resolution 2560 x 1920 @15 fps , 25-30 mts length range IP 67 colour 0.01 Lux , BLC/3D NDR /ROI/HCL , CP PLUS/HONEYWELL/UNV (Higer end) (Data A32)
41
-
-
... More
Supply and installation of 8 Port PoE switch for CCTV IP camera , D-Link/TP link/net gear (Higher end) (Data A33)
12
-
-
... More
Supply and Installation of 32 channel Network Video recorder with 2 sata , (2 Nos. Hard disc) recording minimum 720P resolution in full HD , Hard disc support 4TB, USB, HDMI should be available with all accessories , HONEYWELL/BOSCH/CP PLUS (Higher end ) (Data A34)
2
-
-
... More
Supply and Installation of 8TB built in Hard Disc drive, WD PURPLE/ SEAGATE /TOSHIBA 3year warrenty (Higher end) (Data A35)
2
-
-
... More
supply and installation of 43 inches 24x7 LED/LFD monitor with full HD with following features. Resolution 1920 x 1080, HDMI , audio in, built in speaker operation.including wall bracket/ stand for fixing the LED/LFD monitor (Higher end) (Data A36)
2
-
-
... More
Supply and run of CAT 6 cable in existing concealed PVC pipe including termination work.(Data A37)
1200
-
-
... More
Supply and run of 25mm dia. PVC rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour (Data A38)
600
-
-
... More
supply and installation of 4U rack with accessories including fan in the above rack for mounting 8 port PoE switch (Data A39)
12
-
-
... More
supply and installation of 12U rack with accessories including fan in the above rack for mounting NVRs (Data A40)
1
-
-
... More
Testing and commissioning including Patch cards , termination charges etc.
1
-
-
... More
FIRE FIGHTING SYSTEM
-
-
-
... More
Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 450 LPM at 20metres head to develop 2.0 kg/sq.cm at the heightest and farthest hydrant point to make 10m water jet at the time of fire fighting emergency cicumstances, coupled with 3.75KW / 5HP rated three phase 415 volts, 50 Hz, 2880 rpm electrical motor, the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia, including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 538 or Equivalent)).
1
-
-
... More
Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required.a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete.
Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc.c. 110 litres capacity diesel tank mounted over stand
fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent).
1
-
-
... More
d. Exhaust system having flexible metallic mufler, 100mm
dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling asper site condition.e. Dash board consisting the instruments like temperaturegauge, galvano type DC Ammeter, lubricant oil pressuregauge, ignition switch, emergency stop and all otherprotection equipment as per specification, stop seleneid forauto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180
AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required.g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement.
All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent
-
-
-
... More
Supplying, installation, testing and commissioning of Fire Fighting Electrical Control Panel of cubical construction, floor
mounted type fabricated using CRCA sheet, compartmentalised with hinged lockable door dust and vermin proof, cable alley, inter connection having switch gears and accessories mounting and internal wiring, earth terminals, numberings, necessary
metering protections and indications complete in all respect suitable for operation on 415volt, 3 phase, 50 Hz AC supply with enclosure protection class IP 54 and mounted with the
followings. A. Common Panel in Fire Pump House(i). Incomer a. 1 No. 600A TP & N SDFU with HRC fuses b. 1 set of 600A, 4 bar aluminium bus bar, 415 V, 50 HZ AC
supply c. 1 No. (0-500A) digital ammeter with selector switch & CTs d. 1 No. (0-500V) digital voltmeter with selector switch and control fuses e. 3 Nos. phase indication lamp LED type with toggle switches with control fuses (ii). Outgoing a. Main Fire Pump 400 A TPN SDFU with HRC fuses with sutable HP fully automatic starter / delta starter with over load protection, digital ammeter with built-in selector switch and suitable CTs, current sensing
type single phasing preventer complete with all accessories and
internal wiring required for automatic operation, selector switch
for auto / manual / OFF operation - 1 No
4
-
-
... More
b. Jockey Pump 125 A TPN SDFU with HRC fuses with suitable HP fully automatic starter / delta starter with over load protection,
current sensing type single phasing preventer complete with all accessories and internal wiring required for automatic operation, selector switch for auto / manual operation - 1 No.c. Diesel Engine Control comprising of:
1. Auto / manual selector switch and 3 attempt starting device, timers and relays as required, push buttons, start / stop in manual mode.
2. Indication lamp for high / low lubricant oil pressure, high water temperature and engine ON indication.3. Battery charger suitable for 12V /24V DC with boost and
tickle selector switch, 0-15V / 0-30V DC volt meter, 0-20A DC ammeter.4. All standard relays and accessories for automatic operation
of diesel engine. 5. The above combined panel mounted over MS channel fabricated frame with cement concrete platform, all other
connection works carried out as per standard methods and including conveying, fixing and incidental charges, etc.,complete as per standard specification and as directed by the
Departmental Officers
-
-
-
... More
Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
8
-
-
... More
Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT
10
-
-
... More
Supply, installation of Fire Fighting Application 180degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the
standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
21
-
-
... More
Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point
including conveyance, all incidental charges,neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT
21
-
-
... More
Servicing the First Aid Hose Reel Drum assembly by disconnecting from hydrant line, replacing shut off nozzle, warm clip, lubricating the rotating assembly, replacing 20mm dia, 30 metres long rubber hose, reconnecting with hydrant system as per standard methods and as directed by the Departmental Officers.
2
-
-
... More
Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT
-
-
-
... More
250mm dia
1
-
-
... More
200mm dia
4
-
-
... More
150mm dia
8
-
-
... More
100mm dia
6
-
-
... More
80mm dia
4
-
-
... More
65mm dia
10
-
-
... More
Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT
-
-
-
... More
200mm dia
1
-
-
... More
150mm dia
1
-
-
... More
Supply, erection,testing and commissioning of Gun Metal Non-Return Valve of size 50mm dia including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.
4
-
-
... More
Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers.
1
-
-
... More
Supply, erection,testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.
2
-
-
... More
Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its
original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR /
EQUIVALENT.
4
-
-
... More
Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT
5
-
-
... More
Supply, erection,testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance,all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: HGURU / ISI MAKE / EQUIVALENT
5
-
-
... More
Supply, erection,testing and commissioning of Cast iron body and Gun metal orstainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.
-
-
-
... More
200mm dia
2
-
-
... More
150mm dia
6
-
-
... More
100mm dia
6
-
-
... More
Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.
-
-
-
... More
150mm dia
60
-
-
... More
100mm dia
50
-
-
... More
Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anticorrosive metal primer, one layer of asphalt tar tape
wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers.
-
-
-
... More
200mm dia
150
-
-
... More
150mm dia
50
-
-
... More
Supply, Installing,testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1000mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved
10
-
-
... More
Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure
gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.
4
-
-
... More
Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT
4
-
-
... More
Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT
4
-
-
... More
Supply and kept in position of Trolley Mounted Water CO2 Stored Pressure Type 50 litres capacity Fire Extinguisher as per IS13385, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition
wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.
1
-
-
... More
Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose,
mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard
specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT\
1
-
-
... More
FIRE ALARM SYSTEM
-
-
-
... More
Supply, installation, testing and commissioning of Micro Processor based Conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt, 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.
1
-
-
... More
Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling
with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and
as directed by the Departmental Officers. (Make: Apollo / Equivalent)
100
-
-
... More
Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)
15
-
-
... More
Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)
15
-
-
... More
Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.
1000
-
-
... More
HVAC
-
-
-
... More
A. VRF TYPE AC
-
-
-
... More
Outdoor unit:
-
-
-
... More
Supply and installation of 10HP VRF outdoor units equipped with hightly efficient invertor scroll compressors, special acrylic precoated heat exchanger, low noise condensor fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing gas charging, pressure testing, leak testing, complete including cartage etc. as required. Refrigerant shall be R410A and all compressors shall be of inverter type only for better efficiency. The part load under normal operating conditions. (SOR -M 2034)
6
-
-
... More
Indoor unit: Supply and Installation of 2.5 TR capacity of High wall Split unit with IDU, ODU, Blower, Compressor, etc.(Quotation enclosed)
4
-
-
... More
Indoor unit: Supply and Installation of 1.5 TR capacity of High wall Split unit with IDU, ODU, Blower, Compressor, etc.,(SOR M-2044)
18
-
-
... More
Supply and fixing of Y joint for suitable model ( SOR M-2060)
16
-
-
... More
Supply and fixing of Hard/soft drawn copper refrigerant piping with all fittings for suction line and liquid line
-
-
-
... More
28.6 mm (SOR M-2049)
255
-
-
... More
22.2 mm (SOR M-2050)
238
-
-
... More
19.1 mm (SOR M-2051)
180
-
-
... More
15.9 mm (SOR M-2052)
178
-
-
... More
12.7 mm (SOR M-2053)
89
-
-
... More
9.5 mm (SOR M-2054)
178
-
-
... More
Supply and fixing of Insulation hose for the copper pipe (SOR M-2013)
1190
-
-
... More
Supply and run of 4 core 10 sq.mm PVC armoured copper cable on wall or floor with suitable MS clamps (Data A1)
345
-
-
... More
Supply and charging of R410A Refrigerent gas (SOR M-2046)
120
-
-
... More
Supply and run of PVC Draining piping with fittings etc.(SOR M-2058)
545
-
-
... More
Supply and fixing of suitable MS angle frames for mounting the VRF outdoor units (Quotation enclosed)
6
-
-
... More
Supply and fixing of suitable stand for Indoor unit (SOR M-1991)
22
-
-
... More
Supply and fixing of Outdoor MS box of size (L-300mm, H-600mm, W-300mm) with door arrangements with AI frame (floor mounted) and leg supports and S&F of 1no. 100A 4 Pole MCB ( Higher end) in the MS box with connection complete (Data A2)
6
-
-
... More
Supply and run of 4 core 6 sq.mm PVC armoured copper cable on wall or floor with suitable MS clamps (Data A3)
180
-
-
... More
Supply and fixing of 25A SP switch with indicator (1 module) in suitable module GI box on wall with front plate with connection complete (Data A4)
22
-
-
... More
Supply and Run of 3 core 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour. (Data A5)
900
-
-
... More
Testing & commissioning , Lifting, shifting and positioning of above units with pressure testing the system , vacummizing, leak testing , gas charging and commissioning of the above (6 nos.x 10 HP VRF) (Quotation enclosed)
6
-
-
... More
B. DUCTABLE AC SYSTEM
-
-
-
... More
Design, Supply Installation, testing and commissioning of 17 TR nominal capacity ceiling suspended High Static Ductable Air conditioner with the Following components.
9
-
-
... More
a) 17 TR capacity ceiling suspended Ductable Air Conditioner high tech, low height, low noise level indoor unit with fin and tube type cooling coil, Detachable type drier provided in refrigerant circuit to reduce moisture content multi stage type distributor for feeding equal quantities of the Refrigerant mixture to all the section of the coil, with required valves, directly coupled blower to reduce troubles and wear & tear compared to belt drive Blower. Thermostatic expansion valve arrangement, lift and pull type aluminium framed durable, washable air filter, Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut sensor type to improve Reliability of compressor. Type QTY- Ceiling Suspended, Blower QTY – 1 Nos, Motor Power – 415V /3Ph/50HZ, Air Flow – 6800cfm.
-
-
-
... More
b)17 TR capacity suitable for ceiling suspended Ductable Air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut sensor out to improve reliability of compressor and condenser shall be made of super slit high efficient aluminium fins mechanically bonded to copper tubes condenser ‘L’ type coil to be rigidly fixed to unit frame with fasteners imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and Vibration. The fans are direct driven 3phase motor with protection. Condensing temperature 130’f for the system operations. Refrigerant Compressor – Scroll, No of Compressor – 1No, Refrigerant – R410A, Power supply – 415V/3Ph/50HZ, No of Fan – 1Nos, Types of Mounting – Rubber mounts with sleeve. (SOR M-1961)
-
-
-
... More
Design, Supply Installation, testing and commissioning of 8.5 TR nominal capacity ceiling suspended High Static Ductable Air conditioner with the Following components.
8
-
-
... More
a) 8.5 TR capacity ceiling suspended Ductable Air Conditioner high tech, low height, low noise level indoor unit with fin and tube type cooling coil, Detachable type drier provided in refrigerant circuit to reduce moisture content multi stage type distributor for feeding equal quantities of the Refrigerant mixture to all the section of the coil, with required valves, directly coupled blower to reduce troubles and wear & tear compared to belt drive Blower. Thermostatic expansion valve arrangement, lift and pull type aluminium framed durable, washable air filter, Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut sensor type to improve Reliability of compressor. Type QTY- Ceiling Suspended, Blower QTY – 1 Nos, Motor Power – 415V /3Ph/50HZ, Air Flow – 3400cfm.
-
-
-
... More
B)8.5 TR capacity suitable for ceiling suspended Ductable Air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut sensor out to improve reliability of compressor and condenser shall be made of super slit high efficient aluminium fins mechanically bonded to copper tubes condenser ‘L’ type coil to be rigidly fixed to unit frame with fasteners imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and Vibration. The fans are direct driven 3phase motor with protection. Condensing temperature 130’f for the system operations. Refrigerant Compressor – Scroll, No of Compressor – 1No, Refrigerant – R410A, Power supply – 415V/3Ph/50HZ, No of Fan – 1Nos, Types of Mounting – Rubber mounts with sleeve. (SOR M-1994)
-
-
-
... More
Supply fabrication and erection of Factory fabricated GI made duct with supports,Gasket, etc., for SupplyAir Duct.
-
-
-
... More
24G (SOR M-2006)
1950
-
-
... More
22G (SOR M-2007)
580
-
-
... More
20G (SOR M-2008)
320
-
-
... More
Supply and Providing of Thermal Insulation of 9mm thick vidoflex with Aluminium foil, Adhesive, etc., (SOR M-2016)
3220
-
-
... More
Supply and providing acoustic for initial portion of ducting with 12mm thick Fibre glass rigid board covered with Tissue paper and aluminium Perforated sheet (SOR M-2015)
410
-
-
... More
Supply and fixing of Continous Grills for Supply and Return Air, etc., (Quotation enclosed)
100
-
-
... More
Supply,Installation,Testing & Commissioning of Heavy Duty hard drawn / soft refrigrant piping with refnet joints.
-
-
-
... More
28.6 MM (SOR M-2049)
1130
-
-
... More
22.22 MM (SOR M-2050)
1610
-
-
... More
15.9 MM (SOR M-2052)
480
-
-
... More
Supply,Installation, of copper pipe to be insulated with 19mm thick for suction and 13mm thick for liquid line with class O make. (M -2013)
3210
-
-
... More
Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour. (SD 336)
1100
-
-
... More
Supply and Charging of R410A refrigerent gas. (SOR M-2046)
300
-
-
... More
Providing and fixing in position the 40mm dia PVC drain pipes with necessary Insualtion for drain cut to required length and installed complete with all necessary fititngs like elbows,tees & reducers (SOR M-2056)
810
-
-
... More
Supply and fixing of flexible Fire Retardant canvas connection between indoor unit and ducting (Quotation enclosed)
17
-
-
... More
Supply and fixing of Duct mouth dampers between Indoor unit to ducting, etc.,(SOR M-2014)
17
-
-
... More
Nitrogen Pressure Testing and commissoning of outdoor unit and Indoor unit (Quotation enclosed)
17
-
-
... More
Supply and fixing of suitable MS angle frames for mounting the VRF outdoor units (Quotation enclosed)
26
-
-
... More
Supply and fixing of suitable MS angle frame with supports as necessary for mounting the indoor units.(Quotation enclosed)
22
-
-
... More
Supply and fixing of Outdoor MS box of size (L-300mm, H-600mm, W-300mm) with door arrangements with AI frame (floor mounted) and leg supports and S&F of 1no. 100A 4 Pole MCB ( Higher end) in the MS box with connection complete (Data A2)
26
-
-
... More
Supply and run of 4 core 10 sq.mm PVC armoured copper cable on wall or floor with suitable MS clamps (Data A1)
200
-
-
... More
Testing & commissioning , Lifting, shifting and positioning of above units with pressure testing the system , vacummizing, leak testing , gas charging and commissioning of the above (4 nos.x 17 TR unit, 2 nos. 8.5 TR unit) (Quotation enclosed)
6
-
-
... More
Sub Total
1
-
-
... More
GST @ 18%
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements