Hindu Religious And Charitable Endowments Tender

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain Cement Conceret 1:4:8 (One Cement five sand and Ten aggregate) using 40mm hard broken granite stone jelly for foundation including dewatering and wherever necessary laying in layers of 15cm thick and consolidated and curing complying with standard specification and as directed by the departmental officers etc., complete.-

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). M20 Grade

Below Ground Level

Ground Floor

First Floor

Supplying & Erecting of steel centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc.,

Up to Grade Beam

Column

Beam Slab

Supplying and Fabrication of Steel and placing in position MS / Ribbed tor steel Grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc,. Complete complying with standard specification in force and as directed by department officials.

Brick work in In Cement Mortar 1:5 using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation and basement

Ground floor

Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately).

Plastering walls with cement mortar 1:5 (One cement fivesand) 12mm thick in all floors and all exposed surfaces including cost and conveyance of materials to site and all labour charges,Curing etc complete.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) (Using Marbonite Tiles (Observed Data))

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing of UPVC windows (Un-plasticized poly vinyl choloride) of casement type open form profile size outer frame 60 x 58 mm and shutter profile size 60 x 78mm both profiles reinforced with GI 1mm 125 GSM and 100 % corrosion free multi colored chamber section with wall thick of 2mm. The EPDM rubber (Black color) covered with all the edges frame shutters the shutter will be provided with Espag multi power point lock and also it operates as handle. The corners and joints to be welded and cleaned. Radiation pin headed brown glass 4mm thick should be provided to the should be provided to the shutters and it should not allow leakage of water at most raging stroms and should have key lockable action, security protective hinges, strong locking system and as per size for arresting noise and energy loss. The connecting mechanism between the sash and outer frame that enables opening of window. The Window should be fixed to the wall with 100 % packing with screws silicon packing round the frames. The Window should got approved from the Engineer Incharge.

Supplying and Fixing of Plain Pre laminated ABS door of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) door shutters moulded with different designs, consisting of alround frame made of water proof solid foam PVS bar of size 20 x 32 mm, reinforced by 32 x 32 mm 2 Nos, for verticals and made out of LVL (Laminated vaneer lumber), core material of 32mm thick high density craft paper honey comb board, sandwitched on both sides with pre laminated ABS sheet of thickness 1.5mm. PVC edge banding of size 0.45mm on vertical sides. hardwares made out of steel coated butterfly hinges - 3 Nos, for each shutter and ISI made SS round lock complete for finished item of work., complete complying with standard specification. The Door shutter and frame should got approved from the Engineer Incharge.

Supplying and fixing of Solid PVC door shutters using 19gauge 19mm MS squrare tubes for styles and outer frames. 15mm MS square tubes for top,lock and bottim rails. The steel tubes shall be covered with 5mm thick solid PVC sheets.Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position inculding necessary furniture and fittings.

Painting the new walls two coats over one coat of priming with best Plastic Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Wiring with 2 x1.5 sq mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module Gl switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point/fan point (for electronic regulator) (5 points/ Coil) Higher End (Data A)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module Gl switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point/ fan point (for electronic regulator) (6 points/Coil) Higher End.) (Data B)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module Gl switch box in flush with wall with 6A two way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End (Data C)

Supply and fixing of 4' 20W LED battern on wall or ceiling or existing duct with TW round blocks with copper leads from fittings to Terminals (Data D)

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting (SD 439)

Supply and fixing of 7W/9W LED for BH point (SD 79)

Supply and Fixing WT bulkhead fitting with guard sutiable lamp 15 LED bulb. (SD-23)

Supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp (SD 504)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall (SD 115)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of 48W LED strect light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with I no.32 mm Gl bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD) 448)

Supply and fixing of 3 nos 6A two module 5 pin socket, 3 nos 6A one module switch with module cover plate (plastic) on suitable module concealed Box (Gl) in flush with wall with connections. Higher End (Set plug) (SD 389)

Supply and fixing of 1 no. 6/16A two module socket, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections Higher End (SD 401)

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for Warmer Plug in flush with wall with carth connection (For Warmer Plug) (SD 143)

Supply and Run of 2 of 2.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion (SD 337)

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion (SD 351)

Supply and Run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion (SD 359)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 525)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 573)

Supply and Laying of 3 1/2 * 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 662)

Supply and clamping of 3 1/2 * 70 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 203)

Supply and fixing of brass cable gland for 3 1/2 * 70 sqmm PVC armoured LTUG cable with earth connection. (SD 167)

Supply and providing cable end termination of 3½ x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 216)

Supply and clamping of 3 1/2 * 25 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 200)

Supply and fixing of brass cable gland for 3 1/2 * 25 sqmm PVC armoured LTUG cable with earth connection. (SD 164)

Supply and providing cable end termination of 3 1/2 * 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 213)

Supply, Erection, testing and commissioning of dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole ELCB RCCB with horizontal busbar chamber, cable chambers and provisions for fixing TNEB Meters. 1. 63A 4 P ELCB/RCCB-2 No. 3. Meter view glass- 2 Nos The busbar chamber shall consist of 4 Nos 25mm x 3mm copper flat for three phases and neutral. The 10sqmm copper wire for interconnection between buese to 1 No 3 phase meter and 10 nos single phase meters to 4P ELCBs respectively. The copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for earth bus shall be provided all round the panel and 10 sqmm copper wire for Double earth connection for all outgoing meters. The panel shall have powder coated painting of approved colours. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a masonary pedestal to be constructed with suitable foundation. The lowest metering chamber shall be a height of 0.75m from the ground level. (note: ELCBs / RCCBs shall be of L&T / Siemens make). (Data C)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall/floor/ ground for earth connection (SD 76)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 371)

Sub Total

GST @ 18%