Hindu Religious And Charitable Endowments Joint Commissioner Office Tirupur Arulmigu Avinashi Lingeswarar Temple Avinashi Tender

Brick Work in following cement Mortar using best quality Fly ash bricks of size 23x11x7 cm for foundation and basement including curing etc., complete complying with standard specification

Cement concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid layers of not more than 15 cm thick well rammed, consolidated and curing etc., complete complying with standard specification

Supplying and filling with gravel including cost and conveyance of gravel and all labour charges for filling ramming etc., complete with standard specifications

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg-m3 and maximum water cement ratio of 0.55 including admixture (Plasticiser-super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability with out impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3.cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg.of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, Centering and shuttering and also including laying,vibrating with mechanical vibrartors, finishing, curing, etc, and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary without claiming wxtra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No Separate payment will be made by the Department for the excess usage of materials)

Supplying, Fabricating and placing in position mild steel-Ribbed T or Steel grills for all RCC Works as per design given includiding cost of steel and G.I binding wire in all floors etc., complete complying with standard specification.

Plastering with Cement Mortar 1:5(one cement and five sand)- 12mm thick in all floors including curing etc, Complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of worj such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One cement and Three sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supply and fixing of PUF roof panels made up minimum 0.5mm thick PPGI corrugated Sheet at the top and a plain sheet at the bottom with a layer of rigid CFC free polyurethane foam (PUF) of density 40kg + 2 kg-cum as insulation in between. The polyurethane foam shall confirm to latest IS 12436. The minimum thickness of PU foam layer shall be 29mm for having 30mm (mn) thick PUF panel. The PPGI Sheets shall be of minimum 240 MPA sheet Grade & shall have a Zinc coating of minimum 120 GSM as per IS 277/1992, 5-7 microns of epoxy primer on both sides of the sheet & polyester top cover of 18-20 microns on one side / outer side. The PPGI Sheets/PUF panels shall have a protective guard film of minimum 20-25 microns to avoid scratches to finished panel during transportation. Providing ridges or hips, encasing the ends of Panel with Plain G.S. Sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers etc complete excluding the cost of trussed, purlins and inclusive of cutting to size and shape wherever required

UPVC Window Specification: supplying and fixing UPVC (Un-Plasticized PolyvinyI Chloride) Windows of Casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, Security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connectingmechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work sqm . UPVE Window M-0674

UPVE Door specification : supplying and fixing UPVC (Un- Plasticized PolyvinyI Chloride) Door of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with GI/1mm 125 GSM and 100% corrosion free, the profiles are mult chambered sections with wall thick of 2mm. The EPDM eubbwe (black colour) covered with over all the edges of frame and shuter the shutter will be provided with Espag multi power point locks and also it operates as handle. the cornersand joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging stors and should have key lockable action, Security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should he fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer brfore use on work sqm. UPVC Door M-0673

Supplying and fixing in position best approved of BIS quality PVC rain water down. Fall pipes having a pressure of 4 kg./ sq.cm including cost of nrcessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall e inclusive of cast of removable cast iron grating. the PVC pipe shall be fixed in wall with special type of "U"clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60 mm thic in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc, complete.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing etc., complete in all floors complying with standard specification (The Wall putty shall be approved by the Executive Engineer before use of work)

Painting old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification/ (The make, quality and colour of paint should be get approved by the Executive Engineer before use on works.)

Distempering the old wall and ceiling one coat with best oil bound distember of approved quality including preparation of surface, the rate includes cost of brushes, high scaffolding arrangements, neat finishes, etc., complete complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with water based exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirl, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing to Teak wood frames 127x76mm size as per standard specifications.

Supplying and fixing of teak wood panelled door shutter using including cost and lobour for fixing the hold fasts and furniture fittings etc., complete as directed by the departmentsl officers complying with standard specification.

Paving the floor with Double charged Verfified tiles of size 600x600x8 mm in all floors over abase layer of cement mortar 1:3 (One Cement and three m-Sand) 20mm thick laid in -size and pointed with same colored cement

Dadooing walls with following best approved quality, white/ colour glazed tiles of following sizes set in cement mortar 1:2 (One cement and two crushed stone sand) 10mm thick andn pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg / sqm neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skis tiles (Required shape design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg/sqm., curing. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tile should be got approved by Executive Engineer before use on works)

Providing and fixing GYP board false ceiling and fixing with a new GYP board False ceiling which includes "U" shaped GI channels of size 25x25x0.5mm thick including all labour charges etc.,(PVCPanel)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated unsheathed SC Cu.Conductor of 100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW swith box and 5A F.T. Swith in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed Light Point/Fan point (For electronic regulator) (SD 25)

Supplying and fixing of 1200mm (48*) AC Ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp(SD 549)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires, in flush with wall, with 150mm x 100with TW swith box and 5A F.T. Swith in flush with wall with 3mm thick hylum sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed oortion with suitable colour for concealed PVC plug point.(SD 26)

Supply and fixing of single 20 W 4 Feet LED Tube light Fitting (Higher End Phlips/ Havells/Equivalent) Complete with on ceiling with PVC unsheathed copper leads from terminals to the fitting. (Data A)

Supply and fixing of single 40 W LED light Fitting (Higher End Phlips/ Havells/Equivalent) Complete with on ceiling with PVC unsheathed copper leads from terminals to the fitting. (Data A)

Supplying and Fixing of 48 W LED Street Light Out door fitting complete with 19mm dia GI pipe (Glass "B") with 1 No 19mm GI Bend complete on the existing post wall with 16A aerial fuse unit on MS Plate with PVC unsheathed copper leads MS clamps and aluminium painting. (SD 535)

Supply and fixing of 48W LED Street Light Out Door Fitting complete with 19mm dia GI Pipe (class :B:) wigh 1 No 19mm GI Bend complete on the existing post wall with 16A aerial fuse unit on MS Plate with PVC unsheathed copper leads MS clamps and aluminium painting (SD 535)

Supply and fixing of horizontal type 4 way triple pole neutral MCB dirtribution board in sheet steel enclosure double door (metal) with 40A 4 pipe MCB isolater as incoming and 12 Nos. 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (like standard make) (SD 179)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection(For AC Plug) (SD 140)

Sub Total

GST @ 18%