Highways Department Tender

Quarry Dust Filling in between body wall including cost and conveyance to the site including labour charges for filling in layers, watering, tamping under optimum moisture content to get the maximum density and all incidental charges etc complete as per MORTH Rev.V Clause No. 304

Providing Colour Designed Concrete Paver Block floor finish with TAMIN Paver Block of size 80 mm thick which has a compressive strength of 16.00 Mt/Sqm. The rate including the cost concrete block loading and conveyance to site and cost of labour for fixing in position the joints should be filled with sand including compacting by using power roller compactor., complete complying with standard specification and also the rate including the labour charges for clearing the heavy and scrub, jungle, levelling the sites, diversion of water and sanitary pipe lines, dismantling the esixting masonry structure etc., complete complying as directed by the departmental officers.

Vibrated Cement Concrete M 20 Grade (Nominal Mix 1:2:4) using 40 mm ISS HBG metal including cost and conveyance of all materials to site, including cost and labour charges for form work and centering, labour charges for laying, compacting, curing and all incidental charges etc., complete for Kerb Wall

Painting two coats of best quality of Synthetic enamal paint of approved colour and quality over the new works including cost of paint , Brush, labour , cleaing the surface free from dust, dirt and other in matters scaffolding etc. complete as per standard specifications.

Providing and fixing reflective Road studs of category “A” raised pavement markers made out of poly carbonate / methyl methecrylate / ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity calues conforming to ASTM D 4280. The reflective raised pavement markers shall also confirm to the MORTH circular No.RW/NH.33023/10/97-DO. III dt 11.06.97. The heifth width and length shall not be less than 15mm, 980mm, and 100mm and with minimum reflective area of 13sqm each side and the slope to the basse shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in double 2 of said MORTH circular. The strength of detachment of the integrated cylindrical shanks,(Of diameter not less than 19+/- 2mm and height not less than 30+/-2mm) from the body is to be minimum value of 500kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturers recommendation and complete as directed by the engineer. The marker shall support a load of 13635kg tested in accordance with ASTM D 4280 and confirming to IRC 35-2015 guidelines and MORTH specification 804 etc..,

Providing and erecting of Retro Reflectorised cautionay Mandatory and Informatory signs (Without definition board) made out of high intensity prismatic grade sheeting confirming to Type - IV standards of IRC 67:2012 and ASTM D 4956-09 specification and fixed over 2 mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25 mm x 3 mm Mild steel angle and supported on a mild steel angle post 75x75x6 mm with a clear height of hot less than 2.10 m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundaion with M 15 grade cement concrete 45cm x 45cm x 60 cm size including cost and conveyancce of all materials, equipment, machinery and labour with all leads and lifts, loading charges necessary for satisfactory, completion of the work as directed by the engineer in charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - reflection as per Table 6.6 of ITC 67-2012. The retro - reflective sheeting shall be covered under 7 warranty issued for field performance and a certified copy of three years outdooe exposure report shall be obtained as per IRC 67:2012 (as per MORT&H Specification No. 801) (90 cm Equilateral triangle)

Cautionary Boards - 90 cm equilateral triangle

Speed limit board - 600 mm dia

Information Boards of Size - 800 x 600 mm

Octogon Board

Providing and erecting of Retro Reflectorised Hazard Marker Trafficc sing made out of high intensity prismatic grade sheeting confirming to Type - IV standards of IRC 67:2012 and ASTM D 4956-09 specification and fixed over 2 mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25 mm x 3 mm Mild steel angle and supported on a mild steel angle post 75x75x6 mm and 0.60 m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground be means of properly designed foundation with M 15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts loading charges necessary for satisfactory completion of the work as directed by the engineer, in charge. High intensity Retro - Reflectro sheet, shall consist of minimum coefficient of Retro - reflection as per Table 6.6 of IRC 67-2012. The retro reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 (as per MORT&H Specification No. 801) (30 cm x 90 cm Rectangular)

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 12%

Total Value put to Tender

Excucess or Less Percentage

Final Value

Add GST at 12% of Final Value

Total Value of Contract Including 12% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 12% of GST )