Highways Department Tender

Road D

Road Markers / Road Stud with Lens Reflector Providing and fixing reflective road studs of 'category A' Raised pavement markers made out of poly carbonate / methyl methercrylate/ ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular No RW / NH. 33023/ 10/ 97-DO.III dt 11.06.97. The height, width and length shall not be less than 15 mm, 90 mm and 100 mm and with minimum reflective area of 13 Sq.cm on each side and the slope to the base shall be 35 + /- 5 degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 + / - 2mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC 35 - 2015 guidelines and MORT&H specification 804 etc., complete

Road A

Road B

Road C

Road D

Direction and Place Identification Signs - Type - XI (For Location of Black sopt, curve, sharp bend, Junction , ghat road and critical zone applications) Providing and erecting of Direction and Place Identification Retro-reflectorised Signs made out of Cube Corner Micro Prismatic Grade Sheeting confirming to Type-XI standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. Micro Prismatic grade Retro Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.9 of IRC 67-2012. The retro-reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specification No.801) (For location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications.

Road E

Road F

Retro - Reflectorised Traffic Signs (without definition board) Type - IV Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge_ High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67- 2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 . (asper MORT&H Specification No.801)

Road A (90cm Equilaterial Triangle )

Road B (90cm Equilaterial Triangle )

Road C (90cm Equilaterial Triangle )

Road D (90cm Equilaterial Triangle )

Retro - Reflectorised Traffic Signs (without definition board) Type - IV Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge_ High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67- 2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 . (asper MORT&H Specification No.801)

Road C (60cm Circular)

Providing and Erecting of Retro - Reflectorised Hazard Marker Traffic Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type - IV. Standards of IRC-67 : 2012 and ASTM D 4956 - 09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild Steel angle and supported on a mild steel angle post 75 X 75 X 6mm and 0.60m below ground level. the sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm X 45cm X 60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directec by the engineer in charge. High intensity Retro - Reflector sheet shall consist of minimum coefficient of Retro - reflection as per Table 6.6 of IRC 67-2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and the certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specificatin No 801) (30cm X 90cm rectangular)

Road A

Road C

Road E

Road F

Retro - Reflectorised Traffic Signs (without definition board) Type - IV Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge_ High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67- 2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 . (asper MORT&H Specification No.801)

Road A (60 x 45cm Rectangle Board)

Road B (60 x 45cm Rectangle Board)

Road C (60 x 45cm Rectangle Board)

Road D (60 x 45cm Rectangle Board)

Rigid Median Marker Providing fixing of Median Marker double sided made of polycarbonate for impact resistance and good weather ability. Polycarbonate used for molding the median marker shall have a minimum Izod impact strength value of 600 J/m at room temperature. The impact strength of the poly carbonate should not decrease to less than 70% of its initial value on being subjected to UV weathering as per ASTM G 155 for 1000 hours or exposure to 2 years of natural weathering. The body of the median marker shall be in the form of an isosceles trapezoidal structure of length 15 cm height and width of 10 x 10 cm. The median marker shall have fluorescent yellow retro - reflective sheeting confirming to Type XI specifications as per ASTM D 4956.Area of reflective sheeting should not be less than 70 cm2. Edge of retro reflective shall be concealed using a grill mesh/ similar mechanism to prevent vandalism and sheeting pilferage. The logo of the manufacturer shall be embossed and painted in contrasting colour on both side of median marker for distinct identification.

Road E

Road F

Road Delineators Supplying and installation of delineators (road way indicators, hazard markers and object markers), 80-100 cm high above ground level, painted at alternatively black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 etc., complete (as per MORT&H specification No. 806)

Road A

Road D

Road E

Road F

Supplying of Solar Raised Pavement Markers made of polycarbonate molded body, solar powered, LED self-illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The product shall support a load of 13635 kg tested in accordance to MORTH and ASTM D 4280 Type H. The product should be resistant to water ingress according to IP 65 standards with IS 12063:1987 Category 2 and should withstand emperatures in the range of -7 C to 70 C. Flashing rate and color of lighting is to be provided as per requirement. There should be minimum current losses of less than 20 micro-amperes in sleep-charging mode to enhance product life and single charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm x 100 mm x 100 mm. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. Warranty Certificate and test reports confirming to compressive strength as per MORTH circular shall be obtained from the manufacturer and submitted to the engineer-in-charge. Two Years Warranty Certificate for Solar RPM for the quantity installed and a certified copy of test reports from an independent test laboratory conforming to water ingress shall be obtained from the Manufacturer by the contractor and submitted to the engineer-in charge

Road B

Providing and Fixing of LED Sloar blinker Res 300mm,24 hours operation,12Ah battery (amaron quanta),75WP module,pole height 4.5mtrs (15feet)MS pole with auto coat paint with Godrej cam lock 2nos for Anti theft protection led ultra hi bright,single concept type,pipe 75mm od with ccu 5amswith installaion 24hrs blinking model, wether proof hosing with luvers" for air vent purpose.LEDS are German Company. Foundation with 15 grade cement 60cmx60cmx100cm, 100cm below ground level as per approved drawing

Road B

Road C

Providing and fixing of Retro Reflectorized Sign Board made out of cube corner micro prismatic grade sheeting of Type - XI standards of IRC 67-2012 and ASTM D 4956-09 specification,Digitally Printed using UV Inkjet Printer (UVIJ) for traffic colour,images / logos / text and laminated with clear electro-cuttable film and applied to properly prepared sign substrates, fixed over 2mm aluminium sheet with back supporting frames of 50x50x6mm Mild Steel 'L' angle and supported on a 150NB (Nominal Bore) pioe with 4.50mm thick with an overall height from top of the board to foundation. The sign board should be of 2.1m clear height from top ground level to the bottom of the sign board 1.10m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete of size 450x450x1100mm including cost and conveyance of all materials, equipment,machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and neccessary for statisfactory completion of the work as directed bt the engineer-in-charge etc., complete. The Micro prismatic sheeting should have minimum 70% cp-efficient of Retro-reflection valus as per table 6.90 of IRC 67-2012. The Retro-Reflective sheeting shall be covered under 10 Years warranty issued for the field performance and a certified copy of 3 Ywars outdoor exposure report shall be obtained as per IRc 67-2012.The warranty shall be inclusive of digitally printed images/ logos/ legends and their bonding to the retro-reflective sheeting (as per MorT&H specification no.801)

Road D

Providing and fixing of Retro Reflectorized Sign Board made out of cube corner micro prismatic grade sheeting of Type - XI standards of IRC 67-2012 and ASTM D 4956-09 specification,Digitally Printed using UV Inkjet Printer (UVIJ) for traffic colour,images / logos / text and laminated with clear electro-cuttable film and applied to properly prepared sign substrates, fixed over 2mm aluminium sheet with back supporting frames of 50x50x6mm Mild Steel 'L' angle and supported on a 150NB (Nominal Bore) pioe with 4.50mm thick with an overall height from top of the board to foundation. The sign board should be of 2.1m clear height from top ground level to the bottom of the sign board 1.10m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete of size 450x450x1100mm including cost and conveyance of all materials, equipment,machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and neccessary for statisfactory completion of the work as directed bt the engineer-in-charge etc., complete. The Micro prismatic sheeting should have minimum 70% cp-efficient of Retro-reflection valus as per table 6.90 of IRC 67-2012. The Retro-Reflective sheeting shall be covered under 10 Years warranty issued for the field performance and a certified copy of 3 Ywars outdoor exposure report shall be obtained as per IRc 67-2012.The warranty shall be inclusive of digitally printed images/ logos/ legends and their bonding to the retro-reflective sheeting (as per MorT&H specification no.801) of Size - 3.64m x 2.42m

Road A

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 18%

Total Value put to Tender

Quoted value

Final Quoted Value

Add GST at 18% of Final Quoted Value

Total Value of Contract Including 18% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 18% of GST )