Highways Department Tender

Providing and erecting of retro-reflectorised Hazard marker traffic sign made out of high intensity Prismatic grade sheeting confirming to Type IV standards of IRC: 67-2012 and ASTMD 4956-09,specification and fixed over 2.00mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75mm x 75mm x 6mm and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials,equipment,machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge.High intensity Retro reflectro sheet shall consist of minimum coefficient of Retro reflection as per Table 6.6 of IRC 67-2012.The retro refective sheeting shall be covered under seven year warrenty issued for field perfomance and a certified copy of three years out door exposer report shall be obtained as per IRC 67-2012 (as per MoRT&H Specification No:801) 30cmx90 cm rectangular

Providing and erecting of retro-reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic grade sheeting confirming Type IV standards of IRC: 67-2012 and ASTMD 4956-09,specification and fixed over 2.00mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75mm x 75mm x 6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials,equipment,machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge.High Intensity retro reflectro sheet shall consist of minimum coefficient of Retro reflection as per Table 6.6 of IRC 67-2012.The retro refective sheeting shall be covered under seven year warrenty issued for field perfomance and a certified copy of three years out door exposer report shall be obtained as per IRC 67-2012 (as per MoRT&H Specification No:801)

(90 cm high octogan)

(60 cm glister traingle)

Providing and erecting of Direction and Place Identification Retro-reflectorised Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost & conveyance of all materials, equipment, machinery &labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro Reflectro sheet shall consist of minimumcoefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro- reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specification No.801) (for sign having area more than 0.9 sqm) Type-IV.

Providing fixing of Rigid median marker double sided made of polycarbonate for impact resistance and good weather ability. Polucarbonate used for molding the median marker shall have a minimum Izod impact strength value of 600 J/m at room temperature. The impact strength of the poly carbonate should not decrease to less than 70% of its initial value on being subjected to UV weathering as per ASTM G 155 for 1000 hours or exposure to 2 years of natural weathering. The body of the median marker shall be in the form of an isosceles trapezoidal structure of length 15cm height and width of 10 x 10cm. The median marker shall have fluorescent yellow retro - reflective sheeting confirming to type XI specifications as per ASTM D 4956. Area of reflective sheeting should not less than 70 cm2. Edge of retro - reflective shall be concealed using a grill/mesh/similar mechanism to prevent vandalism and sheeting pilferage. The logo of the manufacturer shall be embossed and painted in contrasting colour on both side of median marker for distinct identification.

Providing and laying of Hot applied Thermoplastic compound 2.5mm thick including reflectoring glass beds @ 250 grms per Sqm. area thickness of 2.50mm is exclusive of surface applied glass beds as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc., complete (as per MORTH specification No. 803)

Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate/methyl methecrylate/ABS moulded body conforming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No RW / NH. 33023/10/ 97-DO.III dt 11.06.97 the height, width and length shall not be less than 15 mm, 90mm and 100 mm and with minimum reflective area of 13 sq.cm. on each side and the slope to the base shall be 35+/-5 degree. Each reflector shall have a CIL not less than values specified in table 2 of said MoRT&H circular.The strength of detachment of the integrated cylinderical shanks,(of diameter not less than 19 +/- 2mm and height not less than 30 +/- 2mm ) from the body is to be a minimum value of 500kgf.Fixing will be by drilling holes on the road for the shanks to go inside,without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The marker shall support a load of 13635kg tested in accordance with ASTM D4280 and confirming to IRC 35 -2015 guide lines and MoRT&H Specification 804 etc., complete.

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 18%

Total Value put to Tender

Difference in Value

Bidder quoted value

Add GST at 18% of Final quoted Value

Total Value of Contract Including 18% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 18% of GST )